| Commit message (Expand) | Author | Age | Files | Lines | |
|---|---|---|---|---|---|
| * | Add initial S2RAM power plane support to Blackbird FPGAHEADv1.02master | Raptor Engineering Development Team | 2021-10-29 | 1 | -4/+59 |
| * | Re-enable pg_reg accessv1.01 | Raptor Engineering Development Team | 2019-06-13 | 1 | -9/+7 |
| * | Fix mode set jumpers not being reported to host | Raptor Engineering Development Team | 2019-06-13 | 1 | -1/+1 |
| * | Fix a few wire declarations that should have been registers | Raptor Engineering Development Team | 2019-06-13 | 1 | -7/+7 |
| * | Mark boot phase pin as pullupv1.00 | Raptor Engineering Development Team | 2019-05-10 | 2 | -3/+14 |
| * | Fix U-boot phase LED blink order | Raptor Engineering Development Team | 2019-05-03 | 1 | -3/+3 |
| * | Disable HDD LED if chassis power is off | Raptor Engineering Development Team | 2019-05-03 | 1 | -3/+8 |
| * | Add option to invert HDD LED signalling | Raptor Engineering Development Team | 2019-05-03 | 1 | -4/+16 |
| * | Switch audio powerdown signal to input and expose to host via manufacturing d... | Raptor Engineering Development Team | 2018-10-09 | 2 | -8/+3 |
| * | Enable power and SATA LEDs | Raptor Engineering Development Team | 2018-09-30 | 2 | -15/+60 |
| * | Initial Remus variant | Raptor Engineering Development Team | 2018-09-30 | 3 | -248/+93 |
| * | Fix regulator test mode | Raptor Engineering Development Team | 2018-06-14 | 1 | -6/+8 |
| * | Add regulator test mode for manufacturing | Raptor Engineering Development Team | 2018-06-11 | 1 | -7/+9 |
| * | Enable pullup on secondary CPU presence detect pin | Raptor Engineering Development Team | 2018-06-06 | 2 | -3/+13 |
| * | Fix LICENSE text | Raptor Engineering Development Team | 2018-05-17 | 1 | -1/+1 |
| * | Remove ATX power good filtering logic | Raptor Engineering Development Team | 2018-05-13 | 1 | -23/+1 |
| * | Move ATX force enable to I2C register 0x33 | Raptor Engineering Development Team | 2018-05-13 | 2 | -13/+22 |
| * | Extend ATX power enable signal | Raptor Engineering Development Team | 2018-05-02 | 1 | -34/+36 |
| * | Update BMC reset logic | Raptor Engineering Development Team | 2018-04-26 | 1 | -3/+3 |
| * | Fix BMC watchdog | Raptor Engineering Development Team | 2018-04-23 | 2 | -60/+83 |
| * | Wire second debug jumper as VGA disable, and expose value to host | Raptor Engineering Development Team | 2018-04-14 | 2 | -5/+4 |
| * | Fix BMC-initiated error clear | Raptor Engineering Development Team | 2018-04-11 | 1 | -2/+2 |
| * | Add BMC startup watchdog | Raptor Engineering Development Team | 2018-03-07 | 1 | -1/+23 |
| * | Add LED override readback | Raptor Engineering Development Team | 2018-02-19 | 1 | -0/+3 |
| * | Add manufacturing fault trace logic for power sequencing | Raptor Engineering Development Team | 2018-02-13 | 1 | -6/+22 |
| * | Enhance front panel LED compatibility with SuperMicro chassis options | Raptor Engineering Development Team | 2018-01-28 | 1 | -6/+21 |
| * | Add pullup on FlexVer™ reset line | Raptor Engineering Development Team | 2018-01-23 | 1 | -2/+12 |
| * | Separate BMC status and chassis reset request lines | Raptor Engineering Development Team | 2018-01-22 | 2 | -16/+8 |
| * | Remove DD1 VCS overcurrent bug hack | Raptor Engineering Development Team | 2018-01-22 | 2 | -11/+1 |
| * | Add I2C write capability | Raptor Engineering Development Team | 2018-01-19 | 3 | -7/+63 |
| * | Switch U-Boot phase indicators to staggered fader | Raptor Engineering Development Team | 2018-01-17 | 1 | -6/+37 |
| * | Indicate BMC boot phase as follows: | Raptor Engineering Development Team | 2018-01-17 | 1 | -6/+48 |
| * | Correct polarity of BMC boot complete signal | Raptor Engineering Development Team | 2018-01-17 | 2 | -9/+39 |
| * | Fix power rails not going offline on system shutdown | Raptor Engineering Development Team | 2018-01-17 | 1 | -2/+2 |
| * | Speed BMC boot pattern up somewhat | Raptor Engineering Development Team | 2018-01-17 | 1 | -2/+2 |
| * | Enable network link and activity LEDs on front and rear panel | Raptor Engineering Development Team | 2018-01-17 | 1 | -12/+77 |
| * | Expose power good/enable busses to I2C for debugging and diagnostic purposes | Raptor Engineering Development Team | 2018-01-16 | 1 | -0/+16 |
| * | Use open drain output on CPU standby reset line | Raptor Engineering Development Team | 2018-01-16 | 1 | -2/+15 |
| * | Take fan controller out of reset when BMC power good is established | Raptor Engineering Development Team | 2018-01-13 | 1 | -2/+2 |
| * | Convert combinatorial logic to registered logic to work around apparent Yosys... | Raptor Engineering Development Team | 2018-01-12 | 3 | -113/+201 |
| * | Fix license template in Makefile | Raptor Engineering Development Team | 2018-01-07 | 1 | -3/+20 |
| * | Add vendor ID registers | Raptor Engineering Development Team | 2017-12-31 | 1 | -3/+22 |
| * | Properly generate programming file | Raptor Engineering Development Team | 2017-12-30 | 1 | -2/+2 |
| * | Add initial Talos™ II front panel control logic | Raptor Engineering Development Team | 2017-12-30 | 3 | -15/+128 |
| * | Remove spurious power_sequencer.v file | Raptor Engineering Development Team | 2017-12-30 | 2 | -224/+2 |
| * | Initial buildable variant for Talos™ II | Raptor Engineering Development Team | 2017-12-30 | 6 | -621/+847 |
| * | Initial conversion pass VHDL to Verilog | Raptor Engineering Development Team | 2017-12-29 | 9 | -1603/+1038 |
| * | Prepare files for Talos™ II modifications | Raptor Engineering Development Team | 2017-12-29 | 3 | -130/+130 |
| * | Initial import of Romulus support files | IBM | 2017-12-29 | 4 | -0/+1603 |
 |
index : blackbird-system-fpga | |
| Blackbird™ FPGA sources | Raptor Computing Systems |
| summaryrefslogtreecommitdiffstats |
|