| Commit message (Expand) | Author | Age | Files | Lines | |
|---|---|---|---|---|---|
| * | [Subtree] Bring openbmc machines to top level | Raptor Engineering Development Team | 2019-04-25 | 29 | -2748/+0 |
| * | Tune CPU fan PID loops for faster attack | Raptor Engineering Development Team | 2019-04-25 | 1 | -2/+2 |
| * | Lower chassis ambient set point due to addition of averaged intake sensors | Raptor Engineering Development Team | 2019-04-25 | 1 | -1/+1 |
| * | Add CPU1 ambient sensor and PCIe ambient sensor to fan control ambient temper... | Raptor Engineering Development Team | 2019-04-25 | 1 | -0/+2 |
| * | Remove unneccessary fan speed maps for chassis fans | Raptor Engineering Development Team | 2019-04-25 | 1 | -16/+2 |
| * | Tweak chassis fan PID controls again to mitigate integrator wind-up | Raptor Engineering Development Team | 2019-04-25 | 1 | -2/+2 |
| * | Tweak chassis fan PID tuning | Raptor Engineering Development Team | 2019-04-25 | 1 | -2/+2 |
| * | Back off chassis fan proportional constant | Raptor Engineering Development Team | 2019-04-25 | 1 | -1/+1 |
| * | Lower chassis fan floor maps slightly to reduce unneccessary fan noise under ... | Raptor Engineering Development Team | 2019-04-25 | 1 | -7/+7 |
| * | Switch to PID control of main fans | Raptor Engineering Development Team | 2019-04-25 | 1 | -62/+65 |
| * | Wait 5 seconds for fans to reach full speed after fan controller init | Raptor Engineering Development Team | 2019-04-25 | 1 | -1/+1 |
| * | Update fan monitor YAML to new syntax | Raptor Engineering Development Team | 2019-04-25 | 1 | -1/+7 |
| * | Update fan event YAML to new syntax | Raptor Engineering Development Team | 2019-04-25 | 1 | -193/+225 |
| * | Make decrease symmetric with increase | Raptor Engineering Development Team | 2019-04-25 | 2 | -12/+12 |
| * | Don't set zone 2 to high speed when fewer than 4 chassis fans are installed, ... | Raptor Engineering Development Team | 2019-04-25 | 1 | -76/+0 |
| * | Tighten up fan response again | Raptor Engineering Development Team | 2019-04-25 | 2 | -15/+15 |
| * | Raise CPU core temp setpoints | Raptor Engineering Development Team | 2019-04-25 | 2 | -71/+71 |
| * | Minimize chassis fan hunting with additional fan speed floor mappings in comm... | Raptor Engineering Development Team | 2019-04-25 | 1 | -7/+13 |
| * | Adjust floor threshold map to avoid chassis fan hunting at typical ambient te... | Raptor Engineering Development Team | 2019-04-25 | 1 | -7/+7 |
| * | Loosen ambient temperature fan controls somewhat | Raptor Engineering Development Team | 2019-04-25 | 1 | -3/+3 |
| * | Set chassis fan speeds based on on-board ambient temperature sensor | Raptor Engineering Development Team | 2019-04-25 | 1 | -60/+11 |
| * | Split fan control zones for CPU0 and CPU1 | Raptor Engineering Development Team | 2019-04-25 | 3 | -22/+93 |
| * | Fix incorrect Talos fan control settings | Raptor Engineering Development Team | 2019-04-25 | 3 | -21/+21 |
| * | Initial port of Witherspoon fan control to Talos | Raptor Engineering Development Team | 2019-04-25 | 29 | -0/+2767 |
 |
index : talos-openbmc | |
| Talos™ II OpenBMC sources | Raptor Computing Systems |
| summaryrefslogtreecommitdiffstats |
|