summaryrefslogtreecommitdiffstats
path: root/meta-openbmc-machines/meta-openpower
Commit message (Expand)AuthorAgeFilesLines
* Move RCS specific layers to correct location for latest OpenBMCTimothy Pearson2019-04-253-65/+0
* Update Talos layer configuration for latest OpenBMC versionRaptor Engineering Development Team2019-04-251-1/+5
* Update RCS layer configuration for latest OpenBMC versionTimothy Pearson2019-04-251-0/+2
* [Subtree] Bring openbmc machines to top levelRaptor Engineering Development Team2019-04-2584-8517/+0
* Don't attempt to control AVSBus regulators on CPU socket 1 when CPU 1 is not ...Raptor Engineering Development Team2019-04-254-18/+89
* Add initial tie-ins for CPU frequency monitoring on BMC via DBUSRaptor Engineering Development Team2019-04-252-0/+112
* Tune CPU fan PID loops for faster attackRaptor Engineering Development Team2019-04-251-2/+2
* Update Talos II fan config for latest phosphor-hwmonRaptor Engineering Development Team2019-04-251-0/+3
* Update OCC monitoring services for new pathsRaptor Engineering Development Team2019-04-254-3/+6
* Raise kernel tick rate and forcibly enable hrtimersRaptor Engineering Development Team2019-04-251-0/+10
* Lower chassis ambient set point due to addition of averaged intake sensorsRaptor Engineering Development Team2019-04-251-1/+1
* Add CPU1 ambient sensor and PCIe ambient sensor to fan control ambient temper...Raptor Engineering Development Team2019-04-251-0/+2
* Add CPU1 ambient sensor to IPMI SDR on Talos IIRaptor Engineering Development Team2019-04-252-0/+23
* Remove unneccessary fan speed maps for chassis fansRaptor Engineering Development Team2019-04-251-16/+2
* Fix ambient temperature sensor mappings on Talos IIRaptor Engineering Development Team2019-04-251-2/+3
* Tweak chassis fan PID controls again to mitigate integrator wind-upRaptor Engineering Development Team2019-04-251-2/+2
* Load final manufacturer ID and device ID data into IPMI data fieldsRaptor Engineering Development Team2019-04-251-1/+1
* Add support for secondary PCIe region ambient temperature sensor on Talos II ...Raptor Engineering Development Team2019-04-253-0/+26
* Add initial IPMI sensor mappings for Talos IIRaptor Engineering Development Team2019-04-256-0/+1865
* Add missing mutability attributes to IPMI inventory YAMLRaptor Engineering Development Team2019-04-251-0/+71
* Update IPMI YAML from Romulus sourceRaptor Engineering Development Team2019-04-251-437/+499
* Bring boot VDN in line with values in datasheetRaptor Engineering Development Team2019-04-251-1/+1
* Fix power sequencing on Talos II.Brandon Bergren2019-04-252-0/+4
* Tweak chassis fan PID tuningRaptor Engineering Development Team2019-04-251-2/+2
* Remove broken ASpeed PWM fan and tach driver tie-inRaptor Engineering Development Team2019-04-252-2/+0
* Back off chassis fan proportional constantRaptor Engineering Development Team2019-04-251-1/+1
* Lower chassis fan floor maps slightly to reduce unneccessary fan noise under ...Raptor Engineering Development Team2019-04-251-7/+7
* Switch to PID control of main fansRaptor Engineering Development Team2019-04-251-62/+65
* Wait 5 seconds for fans to reach full speed after fan controller initRaptor Engineering Development Team2019-04-251-1/+1
* Update fan monitor YAML to new syntaxRaptor Engineering Development Team2019-04-251-1/+7
* Update fan event YAML to new syntaxRaptor Engineering Development Team2019-04-251-193/+225
* Make decrease symmetric with increaseRaptor Engineering Development Team2019-04-252-12/+12
* Don't set zone 2 to high speed when fewer than 4 chassis fans are installed, ...Raptor Engineering Development Team2019-04-251-76/+0
* Tighten up fan response againRaptor Engineering Development Team2019-04-252-15/+15
* Raise CPU core temp setpointsRaptor Engineering Development Team2019-04-252-71/+71
* Allow the on-board VGA device to be enabled or disabled based on FPGA jumper ...Raptor Engineering Development Team2019-04-253-0/+59
* Minimize chassis fan hunting with additional fan speed floor mappings in comm...Raptor Engineering Development Team2019-04-251-7/+13
* Adjust floor threshold map to avoid chassis fan hunting at typical ambient te...Raptor Engineering Development Team2019-04-251-7/+7
* Loosen ambient temperature fan controls somewhatRaptor Engineering Development Team2019-04-251-3/+3
* Set chassis fan speeds based on on-board ambient temperature sensorRaptor Engineering Development Team2019-04-251-60/+11
* Use hardbeep instead of softbeep on Talos systemsRaptor Engineering Development Team2019-04-251-1/+1
* Split fan control zones for CPU0 and CPU1Raptor Engineering Development Team2019-04-253-22/+93
* Add softbeep packaging filesRaptor Engineering Development Team2019-04-251-1/+1
* Remove DD1 VCS workaround hackRaptor Engineering Development Team2019-04-256-76/+0
* Fix incorrect Talos fan control settingsRaptor Engineering Development Team2019-04-253-21/+21
* Enable ambient temperature sensorRaptor Engineering Development Team2019-04-252-0/+2
* Enable the W83773G driver on Talos systemsRaptor Engineering Development Team2019-04-251-0/+1
* Enable Talos IPL monitor LED serviceRaptor Engineering Development Team2019-04-251-1/+1
* Signal BMC ready when BMC has finished booting on Talos systemsRaptor Engineering Development Team2019-04-251-0/+3
* Initial port of Witherspoon fan control to TalosRaptor Engineering Development Team2019-04-2543-7/+2931
OpenPOWER on IntegriCloud