summaryrefslogtreecommitdiffstats
path: root/arch/arm/include/asm/arch-am33xx/clocks_am33xx.h
Commit message (Collapse)AuthorAgeFilesLines
* ARM: AM43xx: EPOS_EVM: Add support for LPDDR2Lokesh Vutla2013-12-181-0/+3
| | | | | | | | | | | | | | | AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A) Adding LPDDR2 init sequence and register details for the same. Below is the brief description of LPDDR2 init sequence: -> Configure VTP -> Configure DDR IO settings -> Disable initialization and refreshes until EMIF registers are programmed. -> Program Timing registers -> Program PHY control and Temp alert and ZQ config registers. -> Enable initialization and refreshes and configure SDRAM CONFIG register -> Wait till initialization is complete and the configure MR registers. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* am335x:Handle worst case scenario for Errata 1.0.24Steve Kipisz2013-09-201-0/+2
| | | | | | | | | | | | | In Errata 1.0.24, if the board is running at OPP50 and has a warm reset, the boot ROM sets the frequencies for OPP100. This patch attempts to drop the frequencies back to OPP50 as soon as possible in the SPL. Then later the voltages and frequencies up set higher. Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Cc: Lars Poeschel <poeschel@lemonage.de> Signed-off-by: Steve Kipisz <s-kipisz2@ti.com> [trini: Adapt to current framework] Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm: am33xx_spl_board_init function and scale core frequencyTom Rini2013-09-201-1/+9
| | | | | | | | | | | | | | | Add a am33xx_spl_board_init (and enable the PMICs) that we may see, depending on the board we are running on. In all cases, we see if we can rely on the efuse_sma register to tell us the maximum speed. In the case of Beaglebone White, we need to make sure we are on AC power, and are on later than rev A1, and then we can ramp up to the PG1.0 maximum of 720Mhz. In the case of Beaglebone Black, we are either on PG2.0 that supports 1GHz or PG2.1. As PG2.0 may or may not have efuse_sma set, we cannot rely on this probe. In the case of the GP EVM, EVM SK and IDK we need to rely on the efuse_sma if we are on PG2.1, and the defaults for PG1.0/2.0. Signed-off-by: Tom Rini <trini@ti.com>
* ARM: AM33xx: Move s_init to a common placeHeiko Schocher2013-08-151-2/+4
| | | | | | | | | | | | s_init has the same outline for all the AM33xx based board. So making it generic. This also helps in addition of new Soc with minimal changes. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Tested-by: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-241-9/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: refactor am33xx clocks and add ti814x supportMatt Porter2013-03-241-29/+2
| | | | | | | Split clock.c for am335x and ti814x and add ti814x specific clock support. Signed-off-by: Matt Porter <mporter@ti.com>
* Allow AM335x MPU core clock speed to be specified in the board config fileMark Jackson2013-03-221-2/+5
| | | | | | | | | | Allow AM335x MPU core clock speed to be specified in the board config file. To use, add the following to the board's config file:- #define CONFIG_SYS_MPUCLK <desired clock freq in MHz> Signed-off-by: Mark Jackson <mpfj@newflow.co.uk> Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
* omap: am33xx: accomodate input clocks other than 24 MhzSteve Sakoman2012-07-071-5/+5
| | | | | | | | | The PLL setup values currently assume a 24 Mhz input clock. This patch uses V_OSCK from the board config file to support boards with different input clock rates. Signed-off-by: Steve Sakoman <steve@sakoman.com>
* ARM:AM33XX: Add clock definitionsChandan Nath2011-10-271-0/+55
This patch adds basic clock definition of am33xx SoC. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OpenPOWER on IntegriCloud