summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
...
| * dm: pci: Mark legacy files as suchSimon Glass2016-01-122-4/+10
| | | | | | | | | | | | | | | | We don't want people changing the legacy PCI files while migration is in progress. Update the file headers to indicate that. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* | ARM: uniphier: fix recommended board setting in documentMasahiro Yamada2016-01-131-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | The mem_is_flash() in arch/arm/mach-uniphier/micro-support_card.c writes/reads the tail of each NOR flash bank to check if the device really resides there. If CS1_SPLIT were enabled, the support card would always require two NOR flash devices to be inserted for the correct NOR detection. This is not probably what we want. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | ARM: uniphier: add dump command for DDR Multi PHY registersMasahiro Yamada2016-01-133-0/+339
| | | | | | | | | | | | | | | | The ProXstream2/PH1-LD6b is integrated with a new IP for DDR PHY which is not register-compatible with the former SoCs. Add a new command to support the register dump of this IP. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | ARM: uniphier: add DRAM init code for ProXstream2/PH1-LD6bMasahiro Yamada2016-01-135-0/+826
| | | | | | | | | | | | | | | | As mentioned in the log of commit 019df879a93e2 (ARM: uniphier: add ProXstream2 and PH1-LD6b support), the DRAM init code was missing for a long time. Finally, here it is. SPL works now. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | ARM: uniphier: move headers out of include/mach directoryMasahiro Yamada2016-01-1377-129/+188
| | | | | | | | | | | | | | These headers are only included locally in arch/arm/mach-uniphier/. There is no reason to export them by putting in the mach/ directory. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | ARM: uniphier: move cmd_pinmon.c to boot-mode subdirectoryMasahiro Yamada2016-01-133-1/+2
| | | | | | | | | | | | | | This command shows the boot mode pins, so it would be more at home in the boot-mode subdirectory. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | ARM: uniphier: move cmd_ddrphy.c to dram subdirectoryMasahiro Yamada2016-01-133-1/+2
| | | | | | | | | | | | | | This command shows the register dump of the DDR PHY, so it would be more at home in the dram subdirectory. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | ARM: uniphier: kill bogus header includesMasahiro Yamada2016-01-1313-15/+0
|/ | | | | | These includes are not necessary. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* Prepare v2016.01Tom Rini2016-01-121-1/+1
| | | | Signed-off-by: Tom Rini <trini@konsulko.com>
* dm: test: usb: Update the USB tests so that they all passSimon Glass2016-01-111-7/+16
| | | | | | | Due to a limitation removed in an earlier patch, USB tests were not seeing all the devices. Update the tests to pass now that all devices are visible. Signed-off-by: Simon Glass <sjg@chromium.org>
* MAINTAINERS/mailmap: Update my email addressFabio Estevam2016-01-1112-12/+12
| | | | | | Update my email address to the NXP account. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2016-01-102-6/+7
|\
| * cgtqmx6eval: README: Fix parameter of 'sf write' commandOtavio Salvador2016-01-101-1/+5
| | | | | | | | | | | | | | | | | | | | | | 'sf command' should receive the length in sector boundaries, so fix it accordingly. Also, show the steps to set the server and board IP addresses for making the steps clearer. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
| * mx6cuboxi: Remove obsolete commentFabio Estevam2016-01-101-4/+0
| | | | | | | | | | | | | | | | | | We currently support various versions of Solidrun mx6 boards, so remove the obsolete comment. Reported-by: Jon Nettleton <jon.nettleton@gmail.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
| * mx6cuboxi: Fix the reset delay for the AR8035 PHYFabio Estevam2016-01-101-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit 59370f3fcd1350 ("net: phy: delay only if reset handler is registered") Ethernet is no longer functional: Booting from net ... FEC Waiting for PHY auto negotiation to complete......... TIMEOUT ! BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 This commit does not have an issue in itself, but it revelead a problem with the Ethernet initialization. As per the AR8035 datasheet: "For a reliable power on reset, suggest to keep asserting the reset low long enough (10ms) to ensure the clock is stable and clock-to-reset 1ms requirement is satisfied." So do as suggested and keep the reset low for 10ms. Also add a 100us delay after deasserting the reset line to guarantee that the PHY ID can be read correctly and the Atheros PHY can be loaded as per Troy Kisky's suggestion. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Tested-by: Tom Rini <trini@konsulko.com>
* | Merge git://git.denx.de/u-boot-rockchipTom Rini2016-01-085-5/+11
|\ \
| * | rockchip: Fix the configuration for chromebook_jerrySimon Glass2016-01-083-3/+9
| | | | | | | | | | | | | | | | | | | | | | | | Various updates did not make it through to this board. Also the instructions for building a SPI image are no-longer correct. Fix these so that Jerry can boot to a prompt again. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | rockchip: Drop a debug message when outputing SPI imagesSimon Glass2016-01-081-1/+1
| | | | | | | | | | | | | | | | | | There is an unnecessary sector count displayed. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | rockchip: Enable generation of SPI imagesSimon Glass2016-01-081-1/+1
| | | | | | | | | | | | | | | | | | This feature was dropped at some point. Restore it. Signed-off-by: Simon Glass <sjg@chromium.org>
* | | Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2016-01-089-79/+41
|\ \ \ | | |/ | |/|
| * | imx_watchdog: always set minimal timeout in reset_cpuAndrey Skvortsov2016-01-072-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | The problem is that timeout bits in WCR register were leaved unchanged. So previously set timeout value was applied and therefore 'reset' command takes any value up to two minutes, depending on previous watchdog settings, instead of minimal 0.5 seconds. Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
| * | gpio: mxs: add name_to_gpio() functionMåns Rullgård2016-01-071-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Override the default name_to_gpio() function with one that accepts strings of the form bank:pin. If a colon is present in the provided name, it behaves like the default version. This lets the "gpio" command work with sane names rather than requiring the user to enter the bank/pin composite in decimal. Signed-off-by: Mans Rullgard <mans@mansr.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
| * | imx: mx7: fix the temperature checking for Rev1.1Peng Fan2016-01-071-8/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To TO1.0, we can not rely on finish bit to read temperature. But to TO1.1, the issue was fixed by IC, we can rely on finish bit for temperature reading for TO1.1. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Adrian Alonso <aalonso@freescale.com>
| * | imx: mx6ul: disable VIDEO for SPLPeng Fan2016-01-071-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With DEBUG macro enabled, SPL build failure: " arch/arm/cpu/armv7/built-in.o: In function `reset_misc': ~/uboot/arch/arm/cpu/armv7/mx6/soc.c:406: undefined reference to `lcdif_power_down' scripts/Makefile.spl:244: recipe for target 'spl/u-boot-spl' failed " Wrap VIDEO settings with ifndef CONFIG_SPL_BUILD Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Stefano Babic <sbabic@denx.de>
| * | pfuze: Fix unsigned variable for less-than-zero comparisonYe.Li2016-01-071-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | According to the Coverity result, a unsigned int variable is used fo less- than-zero comparison, the result is never true. Need to fix the variable type to signed int. Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Stefano Babic <sbabic@denx.de>
| * | wandboard: Simplify the Ethernet PHY configurationFabio Estevam2016-01-071-34/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As per the AR8031 datasheet: "For a reliable power on reset, suggest to keep asserting the reset low long enough (10ms) to ensure the clock is stable and clock-to-reset 1ms requirement is satisfied." So do as suggested and also add a 100us delay after deasserting the reset line to guarantee that the PHY ID can be read correctly and the Atheros 8031 PHY driver can be loaded automatically. This results in a simpler code. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | mx6sabresd: Simplify the Ethernet PHY configurationFabio Estevam2016-01-071-34/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As per the AR8031 datasheet: "For a reliable power on reset, suggest to keep asserting the reset low long enough (10ms) to ensure the clock is stable and clock-to-reset 1ms requirement is satisfied." So do as suggested and also add a 100us delay after deasserting the reset line to guarantee that the PHY ID can be read correctly and the Atheros 8031 PHY driver can be loaded automatically. This results in a simpler code. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | phy: atheros: Use ar8035_config for AR8031Fabio Estevam2016-01-071-1/+1
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 08ad9b068afb88 (" ar8031: modify the config func of ar8031 to ar8021_config") selected 'ar8021_config' as the configuration function for AR8031. The correct would be to use 'ar8035_config' instead as AR8031/AR8035 have the same programming model and even share the same phy driver in the linux kernel: drivers/net/phy/at803x.c. Tested on a mx6qsabresd and wandboard, which now can work without any PHY setup code in the board files. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* | pci: layerscape: Adjust the return value when ls_pcie_addr_valid() failsBin Meng2016-01-081-1/+1
| | | | | | | | | | | | | | | | | | When trying to access non-existent/unsupported PCI devices in ls_pcie_read_config(), when ls_pcie_addr_valid() fails it returns error code and fills in the result with 0xffffffff manually. But it really should return zero to upper layer codes. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
* | pci: imx: Adjust the return value when imx_pcie_addr_valid() failsBin Meng2016-01-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | When trying to access non-existent/unsupported PCI devices in imx_pcie_read_config(), when imx_pcie_addr_valid() fails it returns error code and fills in the result with 0xffffffff manually. But it really should return zero to upper layer codes. Reported-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
* | fs: handle the fileaddr variable in the same way as in the network caseDavid Müller (ELSOFT AG)2016-01-081-0/+1
| | | | | | | | Signed-off-by: David Müller <d.mueller@elsoft.ch>
* | get_maintainer: fix perl 5.22/5.24 deprecated/incompatible "\C" useHeiko Schocher2016-01-081-11/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | from linux commit ce8155f7a3d5: Perl 5.22 emits a deprecated message when "\C" is used in a regex. Perl 5.24 will disallow it altogether. Fix it by using [A-Z] instead of \C. >From linux adapted to U-Boot by: Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
* | fix always succesful memory testRasmus Villemoes2016-01-081-2/+2
| | | | | | | | | | | | | | | | | | Since 51209b1f42cb ("Use common mtest iteration counting"), do_mem_mtest has always reported 0 errors and hence returned 0, even if errors were detected. Fix the helpers mem_test_alt() and mem_test_quick() to return the number of errors found. Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
* | cyrus: Enable STDIO deregisterAndy Fleming2016-01-081-0/+1
| | | | | | | | | | | | | | | | If CONFIG_SYS_STDIO_DEREGISTER is not enabled, usb reset will fail every time. Enabling it allows usb reset to work. Signed-off-by: Andy Fleming <afleming@gmail.com>
* | MAINTAINERS, .mailmap: Update my email addressYork Sun2016-01-084-5/+6
| | | | | | | | | | | | Change from yorksun@freescale.com to york.sun@nxp.com. Signed-off-by: York Sun <york.sun@nxp.com>
* | am33xx/am43xx: Add platform data for GPIOsTom Rini2016-01-081-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | On these platforms we have many cases of boards that enable device model and GPIO support but do not enable OF_CONTROL and pass in a device tree with the binary. We need to bring in the platform data here as well. Tested on Beaglebone Black. Reported-by: Robert Nelson <robertcnelson@gmail.com> Reported-by: Francisco Aguerre <franciscoaguerre@gmail.com> Reported-by: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Tom Rini <trini@konsulko.com>
* | serial: zynq: Use static inline for _debug_uart_init()Michal Simek2016-01-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Mark _debug_uart_init() as static to avoid sparse warning and inline it to debug_uart_init(). Reported-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Thomas Chou <thomas@wytron.com.tw> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
* | net: remove scary warning about EEPROM provided MAC addressAndre Przywara2016-01-081-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In many parts of the computing world having a unique MAC address sitting in some on-NIC storage is considered the normal case. Remove the warning to not scare the user unnecessarily. This applies to Highbank/Midway and ARM's Juno, for instance. Besides that this fixes the formatting on Midway, for instance, which currently looks like: ... Net: xgmac0 Warning: xgmac0 using MAC address from net device , xgmac1 Warning: xgmac1 using MAC address from net device ... Signed-off-by: Andre Przywara <andre.przywara@arm.com>
* | arm64: Juno/FVP: adjust kernel load addressAndre Przywara2016-01-081-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The default kernel load offset for an arm64 kernel is 0x80000, so U-Boot takes cares of moving the loaded kernel to a matching memory location just before booting it. Since we run with caches off, this takes a while for any decently sized kernel - with no output explaining the reason for the delay (unless one uses a DEBUG build). By adjusting the default load offset for Juno and VFP to be 512K aligned in the first place we can skip this copying and boot much faster. Tested on Juno. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
* | arm, Makefile: correct compilation flag for u-boot-dtbAneesh Bansal2016-01-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | The compilation of u-boot-dtb.img should be controlled by CONFIG_OF_CONTROL and not CONFIG_DM. CONFIG_DM may be defined even without Device Tree requirement. This was added in commit 947cee1127c5fa97529c8cda4f0b48d141f92560. Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> CC: Alison Wang <alison.wang@freescale.com>
* | bootcount: Correct #endif comment to match, other aestheticsRobert P. J. Day2016-01-081-6/+4
| | | | | | | | | | | | | | | | | | Correct mismatched comment on #endif to agree with its #if defined(). Also add some missing #endif comments for consistency, take out extraneous blank lines for readability. rday
* | doc: Tidy up first part of top-level README fileRobert P. J. Day2016-01-081-85/+43
| | | | | | | | | | | | | | | | | | | | | | | | First (small) pass at tidying up the README file, including: * remove references to obsolete CREDITS file * remove (some) references to obsolete boards.cfg file * remove at least one reference to a "scrapped" board * cut down unnecessarily detailed directory hierarchy * bunch of grammar and spelling tweaks Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
* | powerpc: Various typo fixes under arch/powerpc/cpu/mpc83xxRobert P. J. Day2016-01-086-20/+20
| | | | | | | | Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
* | include: Correct "requset" typoes in misc.hRobert P. J. Day2016-01-081-2/+2
| | | | | | | | | | Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Acked-by: Thomas Chou <thomas@wytron.com.tw>
* | Merge git://git.denx.de/u-boot-dmTom Rini2016-01-089-17/+83
|\ \
| * | net: Fix delay in net_retry testJoe Hershberger2016-01-072-5/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Introduced in 45b4773 (net/arp: account for ARP delay, avoid duplicate packets on timeout) Check the arp timeout and adjust the timeout start time before the call to eth_recv() so that the sandbox driver has the opportunity to adjust the sandbox timer after the new start time has been recorded. Also, change the adjustment amount by 11 seconds instead of exactly the 10 seconds that the ping timout is expecting since the timeout check is looking for the time elapsed to be greater than but not equal to the specified delay. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Acked-by: Simon Glass <sjg@chromium.org>
| * | fdt: fix address cell count checking in fdt_translate_address()Przemyslaw Marczak2016-01-071-4/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit: dm: core: Enable optional use of fdt_translate_address() Enables use of this function as default, but after this it's not possible to get dev address for the case in which: '#size-cells == 0' This causes errors when getting address for some GPIOs, for which the '#size-cells' is set to 0. Example error: '__of_translate_address: Bad cell count for gpx0' Allowing for that case by modifying the macro 'OF_CHECK_COUNTS', (called from )__of_translate_address(), fixes the issue. Now, this macro doesn't check, that '#size-cells' is greater than 0. This is possible from the specification point of view, but I'm not sure that it doesn't introduce a regression for other configs. Please test and share the results. Tested-on: Odroid U3, Odroid X2, Odroid XU3, Sandbox. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Marek Vasut <marex@denx.de> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com>
| * | dm: usb: Add a remove() method for USB keyboardsSimon Glass2016-01-071-0/+36
| | | | | | | | | | | | | | | | | | | | | | | | At present USB keyboards are not properly removed with driver model. Add the code to handle this. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Marek Vasut <marex@denx.de>
| * | usb: Allow up to 7 storage devicesSimon Glass2016-01-072-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The current limit of 5 is not enough for the driver model USB tests. Really we should not have a limit but the driver model code still uses the usb_dev_desc[] array, which has a limit. Increasing the limit by 2 should not bother anyone. Adjust it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Marek Vasut <marex@denx.de>
| * | dm: Disable all SPI and SPI flash testsSimon Glass2016-01-071-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This subsystem has been broken since commit: 4efad20a sf: Update status reg check in spi_flash_cmd_wait_ready There has so far been no response from the maintainer, and a release is imminent. For now, let's just disable the tests. Signed-off-by: Simon Glass <sjg@chromium.org>
OpenPOWER on IntegriCloud