Merge git://www.denx.de/git/u-boot-ppc4xx

4 files changed, 0 insertions, 868 deletions

diff --git a/include/configs/ebony.h b/include/configs/ebony.h
deleted file mode 100644
index 3f0ad69738..0000000000
--- a/include/configs/ebony.h
+++ /dev/null
@@ -1,174 +0,0 @@
-/*
- * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/************************************************************************
- * board/config_EBONY.h - configuration for AMCC 440GP Ref (Ebony)
- ***********************************************************************/
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*-----------------------------------------------------------------------
- * High Level Configuration Options
- *----------------------------------------------------------------------*/
-#define CONFIG_EBONY		1	    /* Board is ebony		*/
-#define CONFIG_440GP		1	    /* Specifc GP support	*/
-#define CONFIG_440		1	    /* ... PPC440 family	*/
-#define CONFIG_BOARD_EARLY_INIT_F 1	    /* Call board_early_init_f	*/
-#define CONFIG_SYS_CLK_FREQ	33333333    /* external freq to pll	*/
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFFC0000
-
-/*
- * Include common defines/options for all AMCC eval boards
- */
-#define CONFIG_HOSTNAME		ebony
-#include "amcc-common.h"
-
-/*
- * Define here the location of the environment variables (FLASH or NVRAM).
- * Note: DENX encourages to use redundant environment in FLASH. NVRAM is only
- *       supported for backward compatibility.
- */
-#if 1
-#define CONFIG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
-#else
-#define CONFIG_ENV_IS_IN_NVRAM	1	/* use NVRAM for environment vars	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_SDRAM_BASE	    0x00000000	    /* _must_ be 0		*/
-#define CONFIG_SYS_FLASH_BASE	    0xff800000	    /* start of FLASH		*/
-#define CONFIG_SYS_PCI_MEMBASE	    0x80000000	    /* mapped pci memory	*/
-#define CONFIG_SYS_ISRAM_BASE	    0xc0000000	    /* internal SRAM		*/
-#define CONFIG_SYS_PCI_BASE	    0xd0000000	    /* internal PCI regs	*/
-
-#define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000)
-#define CONFIG_SYS_FPGA_BASE	    (CONFIG_SYS_PERIPHERAL_BASE + 0x08300000)
-
-/*-----------------------------------------------------------------------
- * Initial RAM & stack pointer (placed in internal SRAM)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_INIT_RAM_ADDR   CONFIG_SYS_ISRAM_BASE  /* Initial RAM address	*/
-#define CONFIG_SYS_INIT_RAM_SIZE    0x2000	    /* Size of used area in RAM	*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Serial Port
- *----------------------------------------------------------------------*/
-#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
-#define CONFIG_SYS_EXT_SERIAL_CLOCK	(1843200 * 6)	/* Ext clk @ 11.059 MHz */
-
-/*-----------------------------------------------------------------------
- * NVRAM/RTC
- *
- * NOTE: Upper 8 bytes of NVRAM is where the RTC registers are located.
- * The DS1743 code assumes this condition (i.e. -- it assumes the base
- * address for the RTC registers is:
- *
- *	CONFIG_SYS_NVRAM_BASE_ADDR + CONFIG_SYS_NVRAM_SIZE
- *
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_NVRAM_SIZE	    (0x2000 - 8)    /* NVRAM size(8k)- RTC regs */
-#define CONFIG_RTC_DS174x	1		    /* DS1743 RTC		*/
-
-#ifdef CONFIG_ENV_IS_IN_NVRAM
-#define CONFIG_ENV_SIZE		0x1000	    /* Size of Environment vars */
-#define CONFIG_ENV_ADDR		\
-	(CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE)
-#endif /* CONFIG_ENV_IS_IN_NVRAM */
-
-/*-----------------------------------------------------------------------
- * FLASH related
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MAX_FLASH_BANKS	3		    /* number of banks	    */
-#define CONFIG_SYS_MAX_FLASH_SECT	32		    /* sectors per device   */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
-
-#define CONFIG_SYS_FLASH_ADDR0         0x5555
-#define CONFIG_SYS_FLASH_ADDR1         0x2aaa
-#define CONFIG_SYS_FLASH_WORD_SIZE     unsigned char
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SECT_SIZE	0x10000	/* size of one complete sector		*/
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
-#define	CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-#endif /* CONFIG_ENV_IS_IN_FLASH */
-
-/*-----------------------------------------------------------------------
- * DDR SDRAM
- *----------------------------------------------------------------------*/
-#define CONFIG_SPD_EEPROM	1	/* Use SPD EEPROM for setup	*/
-#define SPD_EEPROM_ADDRESS {0x53,0x52}	/* SPD i2c spd addresses	*/
-#define CONFIG_PROG_SDRAM_TLB	1	/* setup SDRAM TLB's dynamically*/
-
-/*-----------------------------------------------------------------------
- * I2C
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
-
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
-#define CONFIG_SYS_I2C_EEPROM_ADDR	(0xa8>>1)
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-
-/*
- * Default environment variables
- */
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	CONFIG_AMCC_DEF_ENV						\
-	CONFIG_AMCC_DEF_ENV_POWERPC					\
-	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
-	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
-	"kernel_addr=ff800000\0"					\
-	"ramdisk_addr=ff810000\0"					\
-	""
-
-#define CONFIG_PHY_ADDR		8	/* PHY address			*/
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_PHY1_ADDR	9	/* EMAC1 PHY address		*/
-
-/*
- * Commands additional to the ones defined in amcc-common.h
- */
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_SNTP
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-/* General PCI */
-#define CONFIG_PCI			            /* include pci support	        */
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_PCI_PNP			        /* do pci plug-and-play         */
-#define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup  */
-#define CONFIG_SYS_PCI_TARGBASE    0x80000000  /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */
-
-/* Board-specific PCI */
-#define CONFIG_SYS_PCI_TARGET_INIT	            /* let board init pci target    */
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe  /* Whatever */
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/ocotea.h b/include/configs/ocotea.h
deleted file mode 100644
index 4ff2f05c88..0000000000
--- a/include/configs/ocotea.h
+++ /dev/null
@@ -1,194 +0,0 @@
-/*
- * (C) Copyright 2004 Paul Reynolds <PaulReynolds@lhsolutions.com>
- *
- * (C) Copyright 2005
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/************************************************************************
- * 1 March 2004	 Travis B. Sawyer <tsawyer@sandburst.com>
- * Adapted to current Das U-Boot source
- ***********************************************************************/
-
-
-/************************************************************************
- * OCOTEA.h - configuration for AMCC 440GX Ref (Ocotea)
- ***********************************************************************/
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*-----------------------------------------------------------------------
- * High Level Configuration Options
- *----------------------------------------------------------------------*/
-#define CONFIG_OCOTEA		1	    /* Board is ebony		*/
-#define CONFIG_440GX		1	    /* Specifc GX support	*/
-#define CONFIG_440		1	    /* ... PPC440 family	*/
-#define CONFIG_BOARD_EARLY_INIT_F 1	    /* Call board_pre_init	*/
-#define CONFIG_SYS_CLK_FREQ	33333333    /* external freq to pll	*/
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFFC0000
-
-/*
- * Include common defines/options for all AMCC eval boards
- */
-#define CONFIG_HOSTNAME		ocotea
-#include "amcc-common.h"
-
-/*-----------------------------------------------------------------------
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH_BASE	    0xff800000	    /* start of FLASH		*/
-#define CONFIG_SYS_PCI_MEMBASE	    0x80000000	    /* mapped pci memory	*/
-#define CONFIG_SYS_ISRAM_BASE	    0xc0000000	    /* internal SRAM		*/
-#define CONFIG_SYS_PCI_BASE	    0xd0000000	    /* internal PCI regs	*/
-
-#define CONFIG_SYS_FPGA_BASE	    (CONFIG_SYS_PERIPHERAL_BASE + 0x08300000)
-#define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000)
-
-/*-----------------------------------------------------------------------
- * Initial RAM & stack pointer (placed in internal SRAM)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_TEMP_STACK_OCM  1
-#define CONFIG_SYS_OCM_DATA_ADDR   CONFIG_SYS_ISRAM_BASE
-#define CONFIG_SYS_INIT_RAM_ADDR   CONFIG_SYS_ISRAM_BASE  /* Initial RAM address	*/
-#define CONFIG_SYS_INIT_RAM_SIZE    0x2000	    /* Size of used area in RAM	*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
-
-/*-----------------------------------------------------------------------
- * Serial Port
- *----------------------------------------------------------------------*/
-#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
-#define CONFIG_SYS_EXT_SERIAL_CLOCK	(1843200 * 6)	/* Ext clk @ 11.059 MHz */
-
-/*-----------------------------------------------------------------------
- * Environment
- *----------------------------------------------------------------------*/
-/*
- * Define here the location of the environment variables (FLASH or NVRAM).
- * Note: DENX encourages to use redundant environment in FLASH. NVRAM is only
- *       supported for backward compatibility.
- */
-#if 1
-#define CONFIG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
-#else
-#define CONFIG_ENV_IS_IN_NVRAM	1	/* use NVRAM for environment vars	*/
-#endif
-
-
-/*-----------------------------------------------------------------------
- * NVRAM/RTC
- *
- * NOTE: Upper 8 bytes of NVRAM is where the RTC registers are located.
- * The DS1743 code assumes this condition (i.e. -- it assumes the base
- * address for the RTC registers is:
- *
- *	CONFIG_SYS_NVRAM_BASE_ADDR + CONFIG_SYS_NVRAM_SIZE
- *
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_NVRAM_SIZE	    (0x2000 - 8)    /* NVRAM size(8k)- RTC regs */
-#define CONFIG_RTC_DS174x	1		    /* DS1743 RTC		*/
-
-#ifdef CONFIG_ENV_IS_IN_NVRAM
-#define CONFIG_ENV_SIZE		0x1000	    /* Size of Environment vars */
-#define CONFIG_ENV_ADDR		\
-	(CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE)
-#endif /* CONFIG_ENV_IS_IN_NVRAM */
-
-/*-----------------------------------------------------------------------
- * FLASH related
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MAX_FLASH_BANKS	3		    /* number of banks	    */
-#define CONFIG_SYS_MAX_FLASH_SECT	64		    /* sectors per device   */
-
-#undef	CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define CONFIG_SYS_FLASH_ADDR0         0x5555
-#define CONFIG_SYS_FLASH_ADDR1         0x2aaa
-#define CONFIG_SYS_FLASH_WORD_SIZE     unsigned char
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SECT_SIZE	0x10000		/* size of one complete sector	*/
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
-#define	CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-#endif /* CONFIG_ENV_IS_IN_FLASH */
-
-/*-----------------------------------------------------------------------
- * DDR SDRAM
- *----------------------------------------------------------------------*/
-#define CONFIG_SPD_EEPROM	1	/* Use SPD EEPROM for setup	*/
-#define SPD_EEPROM_ADDRESS {0x53,0x52}	/* SPD i2c spd addresses	*/
-#define CONFIG_PROG_SDRAM_TLB	1	/* setup SDRAM TLB's dynamically*/
-
-/*-----------------------------------------------------------------------
- * I2C
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
-
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
-#define CONFIG_SYS_I2C_EEPROM_ADDR	(0xa8>>1)
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-
-/*
- * Default environment variables
- */
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	CONFIG_AMCC_DEF_ENV						\
-	CONFIG_AMCC_DEF_ENV_PPC						\
-	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
-	"kernel_addr=fff00000\0"					\
-	"ramdisk_addr=fff10000\0"					\
-	""
-
-#define CONFIG_PHY_ADDR		1	/* PHY address, See schematics	*/
-#define CONFIG_PHY1_ADDR	2
-#define CONFIG_PHY2_ADDR	0x10
-#define CONFIG_PHY3_ADDR	0x18
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#define CONFIG_HAS_ETH3
-#define CONFIG_CIS8201_PHY	1	/* Enable 'special' RGMII mode for Cicada phy */
-#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
-#define CONFIG_PHY_RESET        1       /* reset phy upon startup         */
-#define CONFIG_PHY_RESET_DELAY	1000
-
-/*
- * Commands additional to the ones defined in amcc-common.h
- */
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_SNTP
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-/* General PCI */
-#define CONFIG_PCI			/* include pci support		*/
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
-#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup	*/
-#define CONFIG_SYS_PCI_TARGBASE    0x80000000	/* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */
-
-/* Board-specific PCI */
-#define CONFIG_SYS_PCI_TARGET_INIT		/* let board init pci target    */
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe	/* Whatever */
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/taihu.h b/include/configs/taihu.h
deleted file mode 100644
index 5c0ce7a2e4..0000000000
--- a/include/configs/taihu.h
+++ /dev/null
@@ -1,307 +0,0 @@
-/*
- * (C) Copyright 2000-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2005-2007
- * Beijing UD Technology Co., Ltd., taihusupport@amcc.com
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-
-#define CONFIG_405EP		1	/* this is a PPC405 CPU */
-#define CONFIG_TAIHU	        1	/*  on a taihu board */
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFFC0000
-
-/*
- * Include common defines/options for all AMCC eval boards
- */
-#define CONFIG_HOSTNAME		taihu
-#include "amcc-common.h"
-
-#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f */
-
-#define CONFIG_SYS_CLK_FREQ     33000000 /* external frequency to pll   */
-
-#define CONFIG_NO_SERIAL_EEPROM
-
-/*----------------------------------------------------------------------------*/
-#ifdef CONFIG_NO_SERIAL_EEPROM
-
-/*
-!-------------------------------------------------------------------------------
-! PLL settings for 333MHz CPU, 111MHz PLB/SDRAM, 55MHz EBC, 33MHz PCI,
-! assuming a 33MHz input clock to the 405EP from the C9531.
-!-------------------------------------------------------------------------------
-*/
-#define PLLMR0_333_111_55_37 (PLL_CPUDIV_1 | PLL_PLBDIV_3 |  \
-			      PLL_OPBDIV_2 | PLL_EXTBUSDIV_2 |  \
-			      PLL_MALDIV_1 | PLL_PCIDIV_3)
-#define PLLMR1_333_111_55_37 (PLL_FBKDIV_10  |  \
-			      PLL_FWDDIVA_3 | PLL_FWDDIVB_3 |  \
-			      PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI)
-#define PLLMR0_333_111_55_111 (PLL_CPUDIV_1 | PLL_PLBDIV_3 |  \
-			       PLL_OPBDIV_2 | PLL_EXTBUSDIV_2 |  \
-			       PLL_MALDIV_1 | PLL_PCIDIV_1)
-#define PLLMR1_333_111_55_111 (PLL_FBKDIV_10  |  \
-			       PLL_FWDDIVA_3 | PLL_FWDDIVB_3 |  \
-			       PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI)
-
-#define PLLMR0_DEFAULT		PLLMR0_333_111_55_37
-#define PLLMR1_DEFAULT		PLLMR1_333_111_55_37
-#define PLLMR0_DEFAULT_PCI66	PLLMR0_333_111_55_111
-#define PLLMR1_DEFAULT_PCI66	PLLMR1_333_111_55_111
-
-#endif
-/*----------------------------------------------------------------------------*/
-
-#define CONFIG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars */
-
-/*
- * Default environment variables
- */
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	CONFIG_AMCC_DEF_ENV						\
-	CONFIG_AMCC_DEF_ENV_PPC						\
-	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
-	"kernel_addr=FC000000\0"					\
-	"ramdisk_addr=FC180000\0"					\
-	""
-
-#define CONFIG_PHY_ADDR		0x14	/* PHY address			*/
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_PHY1_ADDR	0x10	/* EMAC1 PHY address		*/
-#define CONFIG_PHY_RESET	1
-
-/*
- * Commands additional to the ones defined in amcc-common.h
- */
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_SPI
-
-#undef CONFIG_SPD_EEPROM		/* use SPD EEPROM for setup */
-#define CONFIG_SYS_SDRAM_SIZE_PER_BANK 0x04000000 /* 64MB */
-#define CONFIG_SYS_SDRAM_BANKS	        2
-
-/*
- * SDRAM configuration (please see cpu/ppc/sdram.[ch])
- */
-#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0 */
-#define CONFIG_SDRAM_BANK1	1	/* init onboard SDRAM bank 1 */
-
-/* SDRAM timings used in datasheet */
-#define CONFIG_SYS_SDRAM_CL            3	/* CAS latency */
-#define CONFIG_SYS_SDRAM_tRP           20	/* PRECHARGE command period */
-#define CONFIG_SYS_SDRAM_tRC           66	/* ACTIVE-to-ACTIVE command period */
-#define CONFIG_SYS_SDRAM_tRCD          20	/* ACTIVE-to-READ delay */
-#define CONFIG_SYS_SDRAM_tRFC		66	/* Auto refresh period */
-
-/*
- * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
- * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
- * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
- * The Linux BASE_BAUD define should match this configuration.
- *    baseBaud = cpuClock/(uartDivisor*16)
- * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
- * set Linux BASE_BAUD to 403200.
- */
-#define CONFIG_CONS_INDEX	2	/* Use UART1			*/
-#undef  CONFIG_SYS_EXT_SERIAL_CLOCK           /* external serial clock */
-#undef  CONFIG_SYS_405_UART_ERRATA_59         /* 405GP/CR Rev. D silicon */
-#define CONFIG_SYS_BASE_BAUD		691200
-
-/*-----------------------------------------------------------------------
- * I2C stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
-
-#define CONFIG_SYS_I2C_NOPROBES	{ {0, 0x69} } /* avoid i2c probe hangup (?) */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	6 /* 24C02 requires 5ms delay */
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* I2C boot EEPROM (24C02W)	*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
-
-#define CONFIG_SOFT_SPI
-#define SPI_SCL  spi_scl
-#define SPI_SDA  spi_sda
-#define SPI_READ spi_read()
-#define SPI_DELAY udelay(2)
-#ifndef __ASSEMBLY__
-void spi_scl(int);
-void spi_sda(int);
-unsigned char spi_read(void);
-#endif
-
-/* standard dtt sensor configuration */
-#define CONFIG_DTT_DS1775	1
-#define CONFIG_DTT_SENSORS	{ 0 }
-#define CONFIG_SYS_I2C_DTT_ADDR	0x49
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define PCI_HOST_ADAPTER 0		/* configure ar pci adapter    */
-#define PCI_HOST_FORCE   1		/* configure as pci host       */
-#define PCI_HOST_AUTO    2		/* detected via arbiter enable */
-
-#define CONFIG_PCI			/* include pci support	       */
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_PCI_HOST	PCI_HOST_FORCE  /* select pci host function    */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play        */
-					/* resource configuration      */
-#define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe	/* Whatever */
-#define CONFIG_SYS_PCI_CLASSCODE       0x0600  /* PCI Class Code: bridge/host */
-#define CONFIG_SYS_PCI_PTM1LA	    0x00000000	/* point to sdram              */
-#define CONFIG_SYS_PCI_PTM1MS      0x80000001	/* 2GB, enable hard-wired to 1 */
-#define CONFIG_SYS_PCI_PTM1PCI     0x00000000	/* Host: use this pci address  */
-#define CONFIG_SYS_PCI_PTM2LA      0x00000000	/* disabled                    */
-#define CONFIG_SYS_PCI_PTM2MS	    0x00000000	/* disabled                    */
-#define CONFIG_SYS_PCI_PTM2PCI     0x04000000	/* Host: use this pci address  */
-#define CONFIG_EEPRO100		1
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- */
-#define CONFIG_SYS_FLASH_BASE		0xFFE00000
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define CONFIG_SYS_FLASH_ADDR0         0x555
-#define CONFIG_SYS_FLASH_ADDR1         0x2aa
-#define CONFIG_SYS_FLASH_WORD_SIZE     unsigned short
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SECT_SIZE	0x10000	/* size of one complete sector	*/
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-#endif /* CONFIG_ENV_IS_IN_FLASH */
-
-/*-----------------------------------------------------------------------
- * NVRAM organization
- */
-#define CONFIG_SYS_NVRAM_BASE_ADDR	0xf0000000	/* NVRAM base address */
-#define CONFIG_SYS_NVRAM_SIZE		0x1ff8		/* NVRAM size */
-
-#ifdef CONFIG_ENV_IS_IN_NVRAM
-#define CONFIG_ENV_SIZE		0x0ff8		/* Size of Environment vars */
-#define CONFIG_ENV_ADDR		\
-	(CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE)	/* Env*/
-#endif
-
-/*-----------------------------------------------------------------------
- * PPC405 GPIO Configuration
- */
-#define CONFIG_SYS_4xx_GPIO_TABLE { /*				GPIO	Alternate1		*/	\
-{												\
-/* GPIO Core 0 */										\
-{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO0	PerBLast    SPI CS	*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO1	TS1E			*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO2	TS2E			*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO3	TS1O			*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO4	TS2O			*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO5	TS3			*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO6	TS4			*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO7	TS5			*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO8	TS6			*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO9	TrcClk			*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO10	PerCS1			*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO11	PerCS2			*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO12	PerCS3			*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO13	PerCS4			*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO14	PerAddr03   SPI SCLK	*/	\
-{ GPIO_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO15	PerAddr04   SPI DI	*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO16	PerAddr05   SPI DO	*/	\
-{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO17	IRQ0	    PCI INTA	*/	\
-{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO18	IRQ1	    PCI INTB	*/	\
-{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO19	IRQ2	    PCI INTC	*/	\
-{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO20	IRQ3	    PCI INTD	*/	\
-{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO21	IRQ4	    USB		*/	\
-{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO22	IRQ5	    EBC		*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO23	IRQ6	    unused	*/	\
-{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO24	UART0_DCD   UART1	*/	\
-{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO25	UART0_DSR		*/	\
-{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO26	UART0_RI		*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO27	UART0_DTR		*/	\
-{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO28	UART1_Rx    UART0	*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO29	UART1_Tx		*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO30	RejectPkt0  User LED1	*/	\
-{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO31	RejectPkt1  User LED2	*/	\
-}												\
-}
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM  0xFC000000	/* FLASH bank #1 */
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in data cache)
- */
-/* use on chip memory (OCM) for temperary stack until sdram is tested */
-#define CONFIG_SYS_TEMP_STACK_OCM        1
-
-/* On Chip Memory location */
-#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
-#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM		*/
-#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM	*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
- */
-
-/* Memory Bank 0 (Flash/SRAM) initialization */
-#define CONFIG_SYS_EBC_PB0AP           0x03815600
-#define CONFIG_SYS_EBC_PB0CR           0xFFE3A000  /* BAS=0xFFE,BS=2MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 1 (NVRAM/RTC) initialization */
-#define CONFIG_SYS_EBC_PB1AP           0x05815600
-#define CONFIG_SYS_EBC_PB1CR           0xFC0BA000  /* BAS=0xFc0,BS=32MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 2 (USB device) initialization */
-#define CONFIG_SYS_EBC_PB2AP           0x03016600
-#define CONFIG_SYS_EBC_PB2CR           0x50018000 /* BAS=0x500,BS=1MB,BU=R/W,BW=8bit */
-
-/* Memory Bank 3 (LCM and D-flip-flop) initialization */
-#define CONFIG_SYS_EBC_PB3AP           0x158FF600
-#define CONFIG_SYS_EBC_PB3CR           0x50118000 /* BAS=0x501,BS=1MB,BU=R/W,BW=8bit */
-
-/* Memory Bank 4 (not install) initialization */
-#define CONFIG_SYS_EBC_PB4AP           0x158FF600
-#define CONFIG_SYS_EBC_PB4CR           0x5021A000
-
-#define CPLD_REG0_ADDR	0x50100000
-#define CPLD_REG1_ADDR	0x50100001
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/taishan.h b/include/configs/taishan.h
deleted file mode 100644
index 3d5c351b1a..0000000000
--- a/include/configs/taishan.h
+++ /dev/null
@@ -1,193 +0,0 @@
-/*
- * (C) Copyright 2007
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/************************************************************************
- * TAISHAN.h - configuration for AMCC 440GX Ref
- ***********************************************************************/
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*-----------------------------------------------------------------------
- * High Level Configuration Options
- *----------------------------------------------------------------------*/
-#define CONFIG_TAISHAN		1	/* Board is taishan		*/
-#define CONFIG_440GX		1	/* Specifc GX support		*/
-#define CONFIG_440		1	/* ... PPC440 family		*/
-#define CONFIG_SYS_CLK_FREQ	33333333 /* external freq to pll	*/
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFFC0000
-
-/*
- * Include common defines/options for all AMCC eval boards
- */
-#define CONFIG_HOSTNAME		taishan
-#define CONFIG_USE_TTY		ttyS1
-#include "amcc-common.h"
-
-#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_pre_init		*/
-#define CONFIG_MISC_INIT_R	1	/* Call misc_init_r		*/
-
-/*-----------------------------------------------------------------------
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH_BASE		0xfc000000	/* start of FLASH	*/
-#define CONFIG_SYS_PCI_MEMBASE		0x80000000	/* mapped pci memory	*/
-#define CONFIG_SYS_ISRAM_BASE		0xc0000000	/* internal SRAM	*/
-#define CONFIG_SYS_PCI_BASE		0xd0000000	/* internal PCI regs	*/
-
-#define CONFIG_SYS_EBC0_FLASH_BASE	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_EBC1_FPGA_BASE	(CONFIG_SYS_PERIPHERAL_BASE + 0x01000000)
-#define CONFIG_SYS_EBC2_LCM_BASE	(CONFIG_SYS_PERIPHERAL_BASE + 0x02000000)
-#define CONFIG_SYS_EBC3_CONN_BASE	(CONFIG_SYS_PERIPHERAL_BASE + 0x08000000)
-
-#define CONFIG_SYS_GPIO_BASE		(CONFIG_SYS_PERIPHERAL_BASE + 0x00000700)
-
-/*-----------------------------------------------------------------------
- * Initial RAM & stack pointer (placed in internal SRAM)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_TEMP_STACK_OCM	1
-#define CONFIG_SYS_OCM_DATA_ADDR	CONFIG_SYS_ISRAM_BASE
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_ISRAM_BASE  /* Initial RAM address	*/
-#define CONFIG_SYS_INIT_RAM_SIZE	0x2000		/* Size of used area in RAM*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
-
-/*-----------------------------------------------------------------------
- * Serial Port
- *----------------------------------------------------------------------*/
-#define CONFIG_CONS_INDEX	2	/* Use UART1			*/
-#define CONFIG_SYS_EXT_SERIAL_CLOCK	(1843200 * 6)	/* Ext clk @ 11.059 MHz */
-
-/*-----------------------------------------------------------------------
- * Environment
- *----------------------------------------------------------------------*/
-#define CONFIG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
-
-/*-----------------------------------------------------------------------
- * FLASH related
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
-
-#define CONFIG_SYS_FLASH_BANKS_LIST    {CONFIG_SYS_FLASH_BASE}
-#define CONFIG_SYS_MAX_FLASH_BANKS     1		    /* number of banks	    */
-#define CONFIG_SYS_MAX_FLASH_SECT	1024		    /* sectors per device   */
-
-#undef	CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define CONFIG_ENV_SECT_SIZE	0x40000 /* size of one complete sector	*/
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
-#define	CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-/*-----------------------------------------------------------------------
- * E2PROM bootstrap configure value
- *----------------------------------------------------------------------*/
-
-/*
- * 800/133/66
- * IIC 0~15: 86 78 11 6a 61 A7 04 62 00 00 00 00 00 00 00 00
- */
-
-/*
- * 800/160/80
- * IIC 0~15: 86 78 c1 a6 09 67 04 63 00 00 00 00 00 00 00 00
- */
-
-/*-----------------------------------------------------------------------
- * DDR SDRAM
- *----------------------------------------------------------------------*/
-#undef CONFIG_SPD_EEPROM		/* Don't use SPD EEPROM for setup	*/
-#define CONFIG_SDRAM_BANK0	1	/* init onboard DDR SDRAM bank 0	*/
-#define	CONFIG_SYS_SDRAM0_TR0		0xC10A401A
-#undef CONFIG_SDRAM_ECC			/* enable ECC support			*/
-
-/*-----------------------------------------------------------------------
- * I2C
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
-
-#undef CONFIG_SYS_I2C_MULTI_EEPROMS
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-
-#define CONFIG_SYS_BOOTSTRAP_IIC_ADDR	0x50
-
-/* I2C SYSMON (LM75, AD7414 is almost compatible)			*/
-#define CONFIG_DTT_LM75		1		/* ON Semi's LM75	*/
-#define CONFIG_DTT_SENSORS	{0}		/* Sensor addresses	*/
-#define CONFIG_SYS_DTT_MAX_TEMP	70
-#define CONFIG_SYS_DTT_LOW_TEMP	-30
-#define CONFIG_SYS_DTT_HYSTERESIS	3
-
-/*
- * Default environment variables
- */
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	CONFIG_AMCC_DEF_ENV						\
-	CONFIG_AMCC_DEF_ENV_POWERPC					\
-	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
-	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
-	"kernel_addr=fc000000\0"					\
-	"ramdisk_addr=fc180000\0"					\
-	"kozio=bootm 0xffe00000\0"					\
-	""
-
-/*-----------------------------------------------------------------------
- * Networking
- *----------------------------------------------------------------------*/
-#define CONFIG_EMAC_NR_START	2	/* start with EMAC 2 (skip 0&1)	*/
-#define CONFIG_PHY_ADDR		0xff	     /* no phy on EMAC0		*/
-#define CONFIG_PHY1_ADDR	0xff	     /* no phy on EMAC1		*/
-#define CONFIG_PHY2_ADDR	0x1
-#define CONFIG_PHY3_ADDR	0x3
-#define CONFIG_ET1011C_PHY	1
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#define CONFIG_HAS_ETH3
-#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
-#define CONFIG_PHY_RESET        1       /* reset phy upon startup         */
-#define CONFIG_PHY_RESET_DELAY	1000
-
-/*
- * Commands additional to the ones defined in amcc-common.h
- */
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_PCI
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-/* General PCI */
-#define CONFIG_PCI			/* include pci support		*/
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
-#define CONFIG_EEPRO100       1		/* include PCI EEPRO100		*/
-#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup	*/
-#define CONFIG_SYS_PCI_TARGBASE    0x80000000	/* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */
-
-/* Board-specific PCI */
-#define CONFIG_SYS_PCI_TARGET_INIT		/* let board init pci target    */
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe	/* Whatever */
-
-#endif	/* __CONFIG_H */