Drop support for GTH board

The board maintainer states:

    The GTH board is obsolete and has not been manufactured for
    several years.
    To my knowledge, no recent U-Boot build has been tested on that
    card.

So drop support for this board.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Thomas Lange <thomas@corelatus.se>
Acked-by: Thomas Lange<thomas@corelatus.se>

2 files changed, 0 insertions, 421 deletions

diff --git a/include/commproc.h b/include/commproc.h
index 9d28abce86..762238ebec 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -828,38 +828,6 @@ typedef struct scc_enet {
 
 #endif	/* CONFIG_GENIETV */
 
-/*** GTH ******************************************************/
-
-#ifdef CONFIG_GTH
-#ifdef CONFIG_FEC_ENET
-#define	FEC_ENET	/* use FEC for EThernet */
-#endif	/* CONFIG_FEC_ETHERNET */
-
-/* This ENET stuff is for GTH 10 Mbit ( SCC ) */
-#define	PROFF_ENET	PROFF_SCC1
-#define	CPM_CR_ENET	CPM_CR_CH_SCC1
-#define	SCC_ENET	0
-
-#define PA_ENET_RXD	((ushort)0x0001) /* PA15 */
-#define PA_ENET_TXD	((ushort)0x0002) /* PA14 */
-#define PA_ENET_TCLK	((ushort)0x0800) /* PA4 */
-#define PA_ENET_RCLK	((ushort)0x0400) /* PA5 */
-
-#define PB_ENET_TENA	((uint)0x00001000) /* PB19 */
-
-#define PC_ENET_CLSN	((ushort)0x0010) /* PC11 */
-#define PC_ENET_RENA	((ushort)0x0020) /* PC10 */
-
-/* NOTE. This is reset for 10Mbit port only */
-#define PC_ENET_RESET	((ushort)0x0100)	/* PC 7 */
-
-#define SICR_ENET_MASK	((uint)0x000000ff)
-
-/* TCLK PA4 -->CLK4, RCLK PA5 -->CLK3 */
-#define SICR_ENET_CLKRT	((uint)0x00000037)
-
-#endif	/* CONFIG_GTH */
-
 /*** HERMES-PRO ******************************************************/
 
 /* The HERMES-PRO uses the FEC on a MPC860T for Ethernet */
diff --git a/include/configs/GTH.h b/include/configs/GTH.h
deleted file mode 100644
index c2cf852d15..0000000000
--- a/include/configs/GTH.h
+++ /dev/null
@@ -1,389 +0,0 @@
-/*
-  * Parameters for GTH board
-  * Based on FADS860T
-  * by thomas.lange@corelatus.com
-
-  * A collection of structures, addresses, and values associated with
-  * the Motorola 860T FADS board.  Copied from the MBX stuff.
-  * Magnus Damm added defines for 8xxrom and extended bd_info.
-  * Helmut Buchsbaum added bitvalues for BCSRx
-  *
-  * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
-  */
-
-/*
- * ff000000 -> ff00ffff : IMAP       internal in the cpu
- * e0000000 -> ennnnnnn : pcmcia
- * 98000000 -> 983nnnnn : FPGA 4MB
- * 90000000 -> 903nnnnn : FPGA 4MB
- * 80000000 -> 80nnnnnn : flash      connected to CS0, final ( real ) location
- * 00000000 -> nnnnnnnn : sdram
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#include <mpc8xx_irq.h>
-
-#define CONFIG_MPC860		1
-#define CONFIG_MPC860T		1
-#define CONFIG_GTH		1
-
-#define CONFIG_MISC_INIT_R      1
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		9600
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-
-#define MPC8XX_FACT		3		/* Multiply by 3 */
-#define MPC8XX_XIN		16384000	/* 16.384 MHz */
-#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))
-
-#define CONFIG_BOOTDELAY	1	/* autoboot after 0 seconds	*/
-
-#define CONFIG_ENV_OVERWRITE 1 /* Allow change of ethernet address */
-
-#define CONFIG_BOOT_RETRY_TIME 5 /* Retry boot in 5 secs */
-
-#define CONFIG_RESET_TO_RETRY 1 /* If timeout waiting for command, perform a reset */
-
-/* Only interrupt boot if space is pressed */
-/* If a long serial cable is connected but */
-/* other end is dead, garbage will be read */
-#define CONFIG_AUTOBOOT_KEYED	1
-#define CONFIG_AUTOBOOT_PROMPT	\
-	"Press space to abort autoboot in %d second\n", bootdelay
-#define CONFIG_AUTOBOOT_DELAY_STR "d"
-#define CONFIG_AUTOBOOT_STOP_STR " "
-
-#if 0
-/* Net boot */
-/* Loads a tftp image and starts it */
-#define CONFIG_BOOTCOMMAND	"bootp;bootm 100000"	/* autoboot command */
-#define CONFIG_BOOTARGS		"panic=1"
-#else
-/* Compact flash boot */
-#define CONFIG_BOOTARGS "panic=1 root=/dev/hda7"
-#define CONFIG_BOOTCOMMAND "disk 100000 0:5;bootm 100000"
-#endif
-
-/* Enable watchdog */
-#define CONFIG_WATCHDOG 1
-
-/* choose SCC1 ethernet (10BASET on motherboard)
- * or FEC ethernet (10/100 on daughterboard)
- */
-#if 1
-#define	CONFIG_SCC1_ENET	1	/* use SCC1 ethernet */
-#undef	CONFIG_FEC_ENET			/* disable FEC ethernet  */
-#define CONFIG_SYS_DISCOVER_PHY
-#else
-#undef	CONFIG_SCC1_ENET		/* disable SCC1 ethernet */
-#define	CONFIG_FEC_ENET		1	/* use FEC ethernet  */
-#define CONFIG_SYS_DISCOVER_PHY
-#endif
-#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET)
-#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured
-#endif
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_IDE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_PROMPT		"=>"	/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0100000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0400000	/* 1 ... 4 MB in DRAM	*/
-
-/* Default location to load data from net */
-#define CONFIG_SYS_LOAD_ADDR		0x100000
-
-#define	CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks	*/
-
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400 }
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR			0xFF000000
-#define CONFIG_SYS_IMMR_SIZE		((uint)(64 * 1024))
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
-#define	CONFIG_SYS_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-
-#define CONFIG_SYS_FLASH_BASE		0x80000000
-
-#define CONFIG_SYS_FLASH_SIZE		((uint)(8 * 1024 * 1024))	/* max 8Mbyte */
-
-#define	CONFIG_SYS_MONITOR_LEN		(384 << 10)	/* Reserve 384 kB for Monitor	*/
-
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
-
-#define	CONFIG_SYS_MALLOC_LEN		(384 << 10)	/* Reserve 384 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	8	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Timeout for Flash Write (in ms)	*/
-
-#define	CONFIG_ENV_IS_IN_FLASH 1
-#undef CONFIG_ENV_IS_IN_EEPROM
-#define CONFIG_ENV_OFFSET		0x000E0000
-#define	CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
-
-#define CONFIG_ENV_SECT_SIZE	0x50000	/* see README - env sector total size	*/
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control					11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration					11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control					11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-
-/*FIXME dont use for now */
-/*#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */
-/*#define CONFIG_SYS_RTCSC	(RTCSC_RTF) */
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-/* PITE */
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register	15-30
- *-----------------------------------------------------------------------
- * set the PLL, the low-power modes and the reset control (15-29)
- */
-#define CONFIG_SYS_PLPRCR	(((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) |	\
-				PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-
-/* FIXME check values */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR	(SCCR_TBS|SCCR_RTSEL|SCCR_COM00|SCCR_DFSYNC00|SCCR_DFBRG00|SCCR_DFNL000|SCCR_DFNH000|SCCR_DFLCD000|SCCR_DFALCD00)
-
- /*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER		0
-
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently.  Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register.  For CS0, you must write the base register
-* first, followed by the option register.
-*/
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-#define FLASH_BASE0_PRELIM	CONFIG_SYS_FLASH_BASE	/* FLASH bank #0	*/
-
-#define CONFIG_SYS_REMAP_OR_AM		0xFF800000	/* 4 MB OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xFF800000	/* OR addr mask */
-
-#define FPGA_2_BASE 0x90000000
-#define FPGA_3_BASE 0x98000000
-
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0	*/
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-
-
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)   /* 1 Mbyte until detected and only 1 Mbyte is needed*/
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_16 )
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-#define CONFIG_ETHADDR          DE:AD:BE:EF:00:01    /* Ethernet address */
-
-#ifdef CONFIG_MPC860T
-
-/* Interrupt level assignments.
-*/
-#define FEC_INTERRUPT	SIU_LEVEL1	/* FEC interrupt */
-
-#endif /* CONFIG_MPC860T */
-
-/* We don't use the 8259.
-*/
-#define NR_8259_INTS	0
-
-/* Machine type
-*/
-#define _MACH_8xx (_MACH_gth)
-
-#ifdef CONFIG_MPC860
-#define PCMCIA_SLOT_A 1
-#define CONFIG_PCMCIA_SLOT_A 1
-#endif
-
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-#define CONFIG_IDE_8xx_PCCARD       1       /* Use IDE with PC Card Adapter */
-#undef  CONFIG_IDE_8xx_DIRECT               /* Direct IDE    not supported  */
-#undef  CONFIG_IDE_LED                  /* LED   for ide not supported  */
-#undef  CONFIG_IDE_RESET                /* reset for ide not supported  */
-
-#define CONFIG_SYS_IDE_MAXBUS          1       /* max. 1 IDE bus               */
-#define CONFIG_SYS_IDE_MAXDEVICE       1       /* max. 1 drive per IDE bus     */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET     0x0000
-#define CONFIG_SYS_ATA_BASE_ADDR       CONFIG_SYS_PCMCIA_MEM_ADDR
-/* Offset for data I/O                  */
-#define CONFIG_SYS_ATA_DATA_OFFSET     (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-/* Offset for normal register accesses  */
-#define CONFIG_SYS_ATA_REG_OFFSET      (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-/* Offset for alternate registers       */
-#define CONFIG_SYS_ATA_ALT_OFFSET      0x0100
-
-#define CONFIG_8xx_GCLK_FREQ   MPC8XX_HZ       /* Force it - dont measure it */
-
-#define PA_FRONT_LED ((u16)0x4) /* PA 13 */
-#define PA_FL_CONFIG ((u16)0x20) /* PA 10 */
-#define PA_FL_CE     ((u16)0x1000) /* PA 3 */
-
-#define PB_ID_GND    ((u32)1) /* PB 31 */
-#define PB_REV_1     ((u32)2) /* PB 30 */
-#define PB_REV_0     ((u32)4) /* PB 29 */
-#define PB_BLUE_LED  ((u32)0x400) /* PB 21 */
-#define PB_EEPROM    ((u32)0x800) /* PB 20 */
-#define PB_ID_3      ((u32)0x2000) /* PB 18 */
-#define PB_ID_2      ((u32)0x4000) /* PB 17 */
-#define PB_ID_1      ((u32)0x8000) /* PB 16 */
-#define PB_ID_0      ((u32)0x10000) /* PB 15 */
-
-/* NOTE. This is reset for 100Mbit port only */
-#define PC_ENET100_RESET	((ushort)0x0080) /* PC 8 */
-
-#endif	/* __CONFIG_H */