diff options
| -rw-r--r-- | Documentation/devicetree/bindings/phy/phy-mapphone-mdm6600.txt | 29 | ||||
| -rw-r--r-- | drivers/phy/motorola/Kconfig | 8 | ||||
| -rw-r--r-- | drivers/phy/motorola/Makefile | 1 | ||||
| -rw-r--r-- | drivers/phy/motorola/phy-mapphone-mdm6600.c | 542 |
4 files changed, 580 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/phy/phy-mapphone-mdm6600.txt b/Documentation/devicetree/bindings/phy/phy-mapphone-mdm6600.txt new file mode 100644 index 000000000000..29427d4f047a --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-mapphone-mdm6600.txt @@ -0,0 +1,29 @@ +Device tree binding documentation for Motorola Mapphone MDM6600 USB PHY + +Required properties: +- compatible Must be "motorola,mapphone-mdm6600" +- enable-gpios GPIO to enable the USB PHY +- power-gpios GPIO to power on the device +- reset-gpios GPIO to reset the device +- motorola,mode-gpios Two GPIOs to configure MDM6600 USB start-up mode for + normal mode versus USB flashing mode +- motorola,cmd-gpios Three GPIOs to control the power state of the MDM6600 +- motorola,status-gpios Three GPIOs to read the power state of the MDM6600 + +Example: + +usb-phy { + compatible = "motorola,mapphone-mdm6600"; + enable-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>; + power-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>; + motorola,mode-gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>, + <&gpio5 21 GPIO_ACTIVE_HIGH>; + motorola,cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>, + <&gpio4 8 GPIO_ACTIVE_HIGH>, + <&gpio5 14 GPIO_ACTIVE_HIGH>; + motorola,status-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>, + <&gpio2 21 GPIO_ACTIVE_HIGH>, + <&gpio2 23 GPIO_ACTIVE_HIGH>; + #phy-cells = <0>; +}; diff --git a/drivers/phy/motorola/Kconfig b/drivers/phy/motorola/Kconfig index 6bb7d6bdf1bf..82651524ffb9 100644 --- a/drivers/phy/motorola/Kconfig +++ b/drivers/phy/motorola/Kconfig @@ -10,3 +10,11 @@ config PHY_CPCAP_USB help Enable this for USB to work on Motorola phones and tablets such as Droid 4. + +config PHY_MAPPHONE_MDM6600 + tristate "Motorola Mapphone MDM6600 modem USB PHY driver" + depends on OF && USB_SUPPORT + select GENERIC_PHY + help + Enable this for MDM6600 USB modem to work on Motorola phones + and tablets such as Droid 4. diff --git a/drivers/phy/motorola/Makefile b/drivers/phy/motorola/Makefile index b6cd618d671a..3514f985b355 100644 --- a/drivers/phy/motorola/Makefile +++ b/drivers/phy/motorola/Makefile @@ -3,3 +3,4 @@ # obj-$(CONFIG_PHY_CPCAP_USB) += phy-cpcap-usb.o +obj-$(CONFIG_PHY_MAPPHONE_MDM6600) += phy-mapphone-mdm6600.o diff --git a/drivers/phy/motorola/phy-mapphone-mdm6600.c b/drivers/phy/motorola/phy-mapphone-mdm6600.c new file mode 100644 index 000000000000..5439dd90d0dd --- /dev/null +++ b/drivers/phy/motorola/phy-mapphone-mdm6600.c @@ -0,0 +1,542 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Motorola Mapphone MDM6600 modem GPIO controlled USB PHY driver + * Copyright (C) 2018 Tony Lindgren <tony@atomide.com> + */ + +#include <linux/delay.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/slab.h> + +#include <linux/gpio/consumer.h> +#include <linux/of_platform.h> +#include <linux/phy/phy.h> + +#define PHY_MDM6600_PHY_DELAY_MS 4000 /* PHY enable 2.2s to 3.5s */ +#define PHY_MDM6600_ENABLED_DELAY_MS 8000 /* 8s more total for MDM6600 */ + +enum phy_mdm6600_ctrl_lines { + PHY_MDM6600_ENABLE, /* USB PHY enable */ + PHY_MDM6600_POWER, /* Device power */ + PHY_MDM6600_RESET, /* Device reset */ + PHY_MDM6600_NR_CTRL_LINES, +}; + +enum phy_mdm6600_bootmode_lines { + PHY_MDM6600_MODE0, /* out USB mode0 and OOB wake */ + PHY_MDM6600_MODE1, /* out USB mode1, in OOB wake */ + PHY_MDM6600_NR_MODE_LINES, +}; + +enum phy_mdm6600_cmd_lines { + PHY_MDM6600_CMD0, + PHY_MDM6600_CMD1, + PHY_MDM6600_CMD2, + PHY_MDM6600_NR_CMD_LINES, +}; + +enum phy_mdm6600_status_lines { + PHY_MDM6600_STATUS0, + PHY_MDM6600_STATUS1, + PHY_MDM6600_STATUS2, + PHY_MDM6600_NR_STATUS_LINES, +}; + +/* + * MDM6600 command codes. These are based on Motorola Mapphone Linux + * kernel tree. + */ +enum phy_mdm6600_cmd { + PHY_MDM6600_CMD_BP_PANIC_ACK, + PHY_MDM6600_CMD_DATA_ONLY_BYPASS, /* Reroute USB to CPCAP PHY */ + PHY_MDM6600_CMD_FULL_BYPASS, /* Reroute USB to CPCAP PHY */ + PHY_MDM6600_CMD_NO_BYPASS, /* Request normal USB mode */ + PHY_MDM6600_CMD_BP_SHUTDOWN_REQ, /* Request device power off */ + PHY_MDM6600_CMD_BP_UNKNOWN_5, + PHY_MDM6600_CMD_BP_UNKNOWN_6, + PHY_MDM6600_CMD_UNDEFINED, +}; + +/* + * MDM6600 status codes. These are based on Motorola Mapphone Linux + * kernel tree. + */ +enum phy_mdm6600_status { + PHY_MDM6600_STATUS_PANIC, /* Seems to be really off */ + PHY_MDM6600_STATUS_PANIC_BUSY_WAIT, + PHY_MDM6600_STATUS_QC_DLOAD, + PHY_MDM6600_STATUS_RAM_DOWNLOADER, /* MDM6600 USB flashing mode */ + PHY_MDM6600_STATUS_PHONE_CODE_AWAKE, /* MDM6600 normal USB mode */ + PHY_MDM6600_STATUS_PHONE_CODE_ASLEEP, + PHY_MDM6600_STATUS_SHUTDOWN_ACK, + PHY_MDM6600_STATUS_UNDEFINED, +}; + +static const char * const +phy_mdm6600_status_name[] = { + "off", "busy", "qc_dl", "ram_dl", "awake", + "asleep", "shutdown", "undefined", +}; + +struct phy_mdm6600 { + struct device *dev; + struct phy *generic_phy; + struct phy_provider *phy_provider; + struct gpio_desc *ctrl_gpios[PHY_MDM6600_NR_CTRL_LINES]; + struct gpio_descs *mode_gpios; + struct gpio_descs *status_gpios; + struct gpio_descs *cmd_gpios; + struct delayed_work bootup_work; + struct delayed_work status_work; + struct completion ack; + bool enabled; /* mdm6600 phy enabled */ + bool running; /* mdm6600 boot done */ + int status; +}; + +static int phy_mdm6600_init(struct phy *x) +{ + struct phy_mdm6600 *ddata = phy_get_drvdata(x); + struct gpio_desc *enable_gpio = ddata->ctrl_gpios[PHY_MDM6600_ENABLE]; + + if (!ddata->enabled) + return -EPROBE_DEFER; + + gpiod_set_value_cansleep(enable_gpio, 0); + + return 0; +} + +static int phy_mdm6600_power_on(struct phy *x) +{ + struct phy_mdm6600 *ddata = phy_get_drvdata(x); + struct gpio_desc *enable_gpio = ddata->ctrl_gpios[PHY_MDM6600_ENABLE]; + + if (!ddata->enabled) + return -ENODEV; + + gpiod_set_value_cansleep(enable_gpio, 1); + + return 0; +} + +static int phy_mdm6600_power_off(struct phy *x) +{ + struct phy_mdm6600 *ddata = phy_get_drvdata(x); + struct gpio_desc *enable_gpio = ddata->ctrl_gpios[PHY_MDM6600_ENABLE]; + + if (!ddata->enabled) + return -ENODEV; + + gpiod_set_value_cansleep(enable_gpio, 0); + + return 0; +} + +static const struct phy_ops gpio_usb_ops = { + .init = phy_mdm6600_init, + .power_on = phy_mdm6600_power_on, + .power_off = phy_mdm6600_power_off, + .owner = THIS_MODULE, +}; + +/** + * phy_mdm6600_cmd() - send a command request to mdm6600 + * @ddata: device driver data + * + * Configures the three command request GPIOs to the specified value. + */ +static void phy_mdm6600_cmd(struct phy_mdm6600 *ddata, int val) +{ + int values[PHY_MDM6600_NR_CMD_LINES]; + int i; + + val &= (1 << PHY_MDM6600_NR_CMD_LINES) - 1; + for (i = 0; i < PHY_MDM6600_NR_CMD_LINES; i++) + values[i] = (val & BIT(i)) >> i; + + gpiod_set_array_value_cansleep(PHY_MDM6600_NR_CMD_LINES, + ddata->cmd_gpios->desc, values); +} + +/** + * phy_mdm6600_status() - read mdm6600 status lines + * @ddata: device driver data + */ +static void phy_mdm6600_status(struct work_struct *work) +{ + struct phy_mdm6600 *ddata; + struct device *dev; + int values[PHY_MDM6600_NR_STATUS_LINES]; + int error, i, val = 0; + + ddata = container_of(work, struct phy_mdm6600, status_work.work); + dev = ddata->dev; + + error = gpiod_get_array_value_cansleep(PHY_MDM6600_NR_CMD_LINES, + ddata->status_gpios->desc, + values); + if (error) + return; + + for (i = 0; i < PHY_MDM6600_NR_CMD_LINES; i++) { + val |= values[i] << i; + dev_dbg(ddata->dev, "XXX %s: i: %i values[i]: %i val: %i\n", + __func__, i, values[i], val); + } + ddata->status = val; + + dev_info(dev, "modem status: %i %s\n", + ddata->status, + phy_mdm6600_status_name[ddata->status & 7]); + complete(&ddata->ack); +} + +static irqreturn_t phy_mdm6600_irq_thread(int irq, void *data) +{ + struct phy_mdm6600 *ddata = data; + + schedule_delayed_work(&ddata->status_work, msecs_to_jiffies(10)); + + return IRQ_HANDLED; +} + +/** + * phy_mdm6600_wakeirq_thread - handle mode1 line OOB wake after booting + * @irq: interrupt + * @data: interrupt handler data + * + * GPIO mode1 is used initially as output to configure the USB boot + * mode for mdm6600. After booting it is used as input for OOB wake + * signal from mdm6600 to the SoC. Just use it for debug info only + * for now. + */ +static irqreturn_t phy_mdm6600_wakeirq_thread(int irq, void *data) +{ + struct phy_mdm6600 *ddata = data; + struct gpio_desc *mode_gpio1; + + mode_gpio1 = ddata->mode_gpios->desc[PHY_MDM6600_MODE1]; + dev_dbg(ddata->dev, "OOB wake on mode_gpio1: %i\n", + gpiod_get_value(mode_gpio1)); + + return IRQ_HANDLED; +} + +/** + * phy_mdm6600_init_irq() - initialize mdm6600 status IRQ lines + * @ddata: device driver data + */ +static void phy_mdm6600_init_irq(struct phy_mdm6600 *ddata) +{ + struct device *dev = ddata->dev; + int i, error, irq; + + for (i = PHY_MDM6600_STATUS0; + i <= PHY_MDM6600_STATUS2; i++) { + struct gpio_desc *gpio = ddata->status_gpios->desc[i]; + + irq = gpiod_to_irq(gpio); + if (irq <= 0) + continue; + + error = devm_request_threaded_irq(dev, irq, NULL, + phy_mdm6600_irq_thread, + IRQF_TRIGGER_RISING | + IRQF_TRIGGER_FALLING | + IRQF_ONESHOT, + "mdm6600", + ddata); + if (error) + dev_warn(dev, "no modem status irq%i: %i\n", + irq, error); + } +} + +struct phy_mdm6600_map { + const char *name; + int direction; +}; + +static const struct phy_mdm6600_map +phy_mdm6600_ctrl_gpio_map[PHY_MDM6600_NR_CTRL_LINES] = { + { "enable", GPIOD_OUT_LOW, }, /* low = phy disabled */ + { "power", GPIOD_OUT_LOW, }, /* low = off */ + { "reset", GPIOD_OUT_HIGH, }, /* high = reset */ +}; + +/** + * phy_mdm6600_init_lines() - initialize mdm6600 GPIO lines + * @ddata: device driver data + */ +static int phy_mdm6600_init_lines(struct phy_mdm6600 *ddata) +{ + struct device *dev = ddata->dev; + int i; + + /* MDM6600 control lines */ + for (i = 0; i < ARRAY_SIZE(phy_mdm6600_ctrl_gpio_map); i++) { + const struct phy_mdm6600_map *map = + &phy_mdm6600_ctrl_gpio_map[i]; + struct gpio_desc **gpio = &ddata->ctrl_gpios[i]; + + *gpio = devm_gpiod_get(dev, map->name, map->direction); + if (IS_ERR(*gpio)) { + dev_info(dev, "gpio %s error %li\n", + map->name, PTR_ERR(*gpio)); + return PTR_ERR(*gpio); + } + } + + /* MDM6600 USB start-up mode output lines */ + ddata->mode_gpios = devm_gpiod_get_array(dev, "motorola,mode", + GPIOD_OUT_LOW); + if (IS_ERR(ddata->mode_gpios)) + return PTR_ERR(ddata->mode_gpios); + + if (ddata->mode_gpios->ndescs != PHY_MDM6600_NR_MODE_LINES) + return -EINVAL; + + /* MDM6600 status input lines */ + ddata->status_gpios = devm_gpiod_get_array(dev, "motorola,status", + GPIOD_IN); + if (IS_ERR(ddata->status_gpios)) + return PTR_ERR(ddata->status_gpios); + + if (ddata->status_gpios->ndescs != PHY_MDM6600_NR_STATUS_LINES) + return -EINVAL; + + /* MDM6600 cmd output lines */ + ddata->cmd_gpios = devm_gpiod_get_array(dev, "motorola,cmd", + GPIOD_OUT_LOW); + if (IS_ERR(ddata->cmd_gpios)) + return PTR_ERR(ddata->cmd_gpios); + + if (ddata->cmd_gpios->ndescs != PHY_MDM6600_NR_CMD_LINES) + return -EINVAL; + + return 0; +} + +/** + * phy_mdm6600_device_power_on() - power on mdm6600 device + * @ddata: device driver data + * + * To get the integrated USB phy in MDM6600 takes some hoops. We must ensure + * the shared USB bootmode GPIOs are configured, then request modem start-up, + * reset and power-up.. And then we need to recycle the shared USB bootmode + * GPIOs as they are also used for Out of Band (OOB) wake for the USB and + * TS 27.010 serial mux. + */ +static int phy_mdm6600_device_power_on(struct phy_mdm6600 *ddata) +{ + struct gpio_desc *mode_gpio0, *mode_gpio1, *reset_gpio, *power_gpio; + int error = 0, wakeirq; + + mode_gpio0 = ddata->mode_gpios->desc[PHY_MDM6600_MODE0]; + mode_gpio1 = ddata->mode_gpios->desc[PHY_MDM6600_MODE1]; + reset_gpio = ddata->ctrl_gpios[PHY_MDM6600_RESET]; + power_gpio = ddata->ctrl_gpios[PHY_MDM6600_POWER]; + + /* + * Shared GPIOs must be low for normal USB mode. After booting + * they are used for OOB wake signaling. These can be also used + * to configure USB flashing mode later on based on a module + * parameter. + */ + gpiod_set_value_cansleep(mode_gpio0, 0); + gpiod_set_value_cansleep(mode_gpio1, 0); + + /* Request start-up mode */ + phy_mdm6600_cmd(ddata, PHY_MDM6600_CMD_NO_BYPASS); + + /* Request a reset first */ + gpiod_set_value_cansleep(reset_gpio, 0); + msleep(100); + + /* Toggle power GPIO to request mdm6600 to start */ + gpiod_set_value_cansleep(power_gpio, 1); + msleep(100); + gpiod_set_value_cansleep(power_gpio, 0); + + /* + * Looks like the USB PHY needs between 2.2 to 4 seconds. + * If we try to use it before that, we will get L3 errors + * from omap-usb-host trying to access the PHY. See also + * phy_mdm6600_init() for -EPROBE_DEFER. + */ + msleep(PHY_MDM6600_PHY_DELAY_MS); + ddata->enabled = true; + + /* Booting up the rest of MDM6600 will take total about 8 seconds */ + dev_info(ddata->dev, "Waiting for power up request to complete..\n"); + if (wait_for_completion_timeout(&ddata->ack, + msecs_to_jiffies(PHY_MDM6600_ENABLED_DELAY_MS))) { + if (ddata->status > PHY_MDM6600_STATUS_PANIC && + ddata->status < PHY_MDM6600_STATUS_SHUTDOWN_ACK) + dev_info(ddata->dev, "Powered up OK\n"); + } else { + ddata->enabled = false; + error = -ETIMEDOUT; + dev_err(ddata->dev, "Timed out powering up\n"); + } + + /* Reconfigure mode1 GPIO as input for OOB wake */ + gpiod_direction_input(mode_gpio1); + + wakeirq = gpiod_to_irq(mode_gpio1); + if (wakeirq <= 0) + return wakeirq; + + error = devm_request_threaded_irq(ddata->dev, wakeirq, NULL, + phy_mdm6600_wakeirq_thread, + IRQF_TRIGGER_RISING | + IRQF_TRIGGER_FALLING | + IRQF_ONESHOT, + "mdm6600-wake", + ddata); + if (error) + dev_warn(ddata->dev, "no modem wakeirq irq%i: %i\n", + wakeirq, error); + + ddata->running = true; + + return error; +} + +/** + * phy_mdm6600_device_power_off() - power off mdm6600 device + * @ddata: device driver data + */ +static void phy_mdm6600_device_power_off(struct phy_mdm6600 *ddata) +{ + struct gpio_desc *reset_gpio = + ddata->ctrl_gpios[PHY_MDM6600_RESET]; + + ddata->enabled = false; + phy_mdm6600_cmd(ddata, PHY_MDM6600_CMD_BP_SHUTDOWN_REQ); + msleep(100); + + gpiod_set_value_cansleep(reset_gpio, 1); + + dev_info(ddata->dev, "Waiting for power down request to complete.. "); + if (wait_for_completion_timeout(&ddata->ack, + msecs_to_jiffies(5000))) { + if (ddata->status == PHY_MDM6600_STATUS_PANIC) + dev_info(ddata->dev, "Powered down OK\n"); + } else { + dev_err(ddata->dev, "Timed out powering down\n"); + } +} + +static void phy_mdm6600_deferred_power_on(struct work_struct *work) +{ + struct phy_mdm6600 *ddata; + int error; + + ddata = container_of(work, struct phy_mdm6600, bootup_work.work); + + error = phy_mdm6600_device_power_on(ddata); + if (error) + dev_err(ddata->dev, "Device not functional\n"); +} + +static const struct of_device_id phy_mdm6600_id_table[] = { + { .compatible = "motorola,mapphone-mdm6600", }, + {}, +}; +MODULE_DEVICE_TABLE(of, phy_mdm6600_id_table); + +static int phy_mdm6600_probe(struct platform_device *pdev) +{ + struct phy_mdm6600 *ddata; + int error; + + ddata = devm_kzalloc(&pdev->dev, sizeof(*ddata), GFP_KERNEL); + if (!ddata) + return -ENOMEM; + + INIT_DELAYED_WORK(&ddata->bootup_work, + phy_mdm6600_deferred_power_on); + INIT_DELAYED_WORK(&ddata->status_work, phy_mdm6600_status); + init_completion(&ddata->ack); + + ddata->dev = &pdev->dev; + platform_set_drvdata(pdev, ddata); + + error = phy_mdm6600_init_lines(ddata); + if (error) + return error; + + phy_mdm6600_init_irq(ddata); + + ddata->generic_phy = devm_phy_create(ddata->dev, NULL, &gpio_usb_ops); + if (IS_ERR(ddata->generic_phy)) { + error = PTR_ERR(ddata->generic_phy); + goto cleanup; + } + + phy_set_drvdata(ddata->generic_phy, ddata); + + ddata->phy_provider = + devm_of_phy_provider_register(ddata->dev, + of_phy_simple_xlate); + if (IS_ERR(ddata->phy_provider)) { + error = PTR_ERR(ddata->phy_provider); + goto cleanup; + } + + schedule_delayed_work(&ddata->bootup_work, 0); + + /* + * See phy_mdm6600_device_power_on(). We should be able + * to remove this eventually when ohci-platform can deal + * with -EPROBE_DEFER. + */ + msleep(PHY_MDM6600_PHY_DELAY_MS + 500); + + return 0; + +cleanup: + phy_mdm6600_device_power_off(ddata); + return error; +} + +static int phy_mdm6600_remove(struct platform_device *pdev) +{ + struct phy_mdm6600 *ddata = platform_get_drvdata(pdev); + struct gpio_desc *reset_gpio = ddata->ctrl_gpios[PHY_MDM6600_RESET]; + + if (!ddata->running) + wait_for_completion_timeout(&ddata->ack, + msecs_to_jiffies(PHY_MDM6600_ENABLED_DELAY_MS)); + + gpiod_set_value_cansleep(reset_gpio, 1); + phy_mdm6600_device_power_off(ddata); + + cancel_delayed_work_sync(&ddata->bootup_work); + cancel_delayed_work_sync(&ddata->status_work); + + return 0; +} + +static struct platform_driver phy_mdm6600_driver = { + .probe = phy_mdm6600_probe, + .remove = phy_mdm6600_remove, + .driver = { + .name = "phy-mapphone-mdm6600", + .of_match_table = of_match_ptr(phy_mdm6600_id_table), + }, +}; + +module_platform_driver(phy_mdm6600_driver); + +MODULE_ALIAS("platform:gpio_usb"); +MODULE_AUTHOR("Tony Lindgren <tony@atomide.com>"); +MODULE_DESCRIPTION("mdm6600 gpio usb phy driver"); +MODULE_LICENSE("GPL v2"); |
