diff options
| -rw-r--r-- | drivers/ide/pci/hpt366.c | 404 |
1 files changed, 174 insertions, 230 deletions
diff --git a/drivers/ide/pci/hpt366.c b/drivers/ide/pci/hpt366.c index 51f40f2db772..787efd35db2b 100644 --- a/drivers/ide/pci/hpt366.c +++ b/drivers/ide/pci/hpt366.c @@ -67,10 +67,9 @@ * - add support for HPT302N and HPT371N clocking (the same as for HPT372N) * - HPT371/N are single channel chips, so avoid touching the primary channel * which exists only virtually (there's no pins for it) - * - fix/remove bad/unused timing tables: HPT370/A 66 MHz tables weren't really - * needed and had many modes over- and underclocked, HPT372 33 MHz table was - * for 66 MHz and 50 MHz table missed UltraDMA mode 6, HPT374 33 MHz table was - * really for 50 MHz; switch to using HPT372 tables for HPT374... + * - fix/remove bad/unused timing tables and use one set of tables for the whole + * HPT37x chip family; save space by introducing the separate transfer mode + * table in which the mode lookup is done * <source@mvista.com> * */ @@ -162,214 +161,168 @@ static const char *bad_ata33[] = { NULL }; -struct chipset_bus_clock_list_entry { - u8 xfer_speed; - unsigned int chipset_settings; +static u8 xfer_speeds[] = { + XFER_UDMA_6, + XFER_UDMA_5, + XFER_UDMA_4, + XFER_UDMA_3, + XFER_UDMA_2, + XFER_UDMA_1, + XFER_UDMA_0, + + XFER_MW_DMA_2, + XFER_MW_DMA_1, + XFER_MW_DMA_0, + + XFER_PIO_4, + XFER_PIO_3, + XFER_PIO_2, + XFER_PIO_1, + XFER_PIO_0 }; -/* key for bus clock timings - * bit - * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW - * DMA. cycles = value + 1 - * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW - * DMA. cycles = value + 1 - * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file - * register access. - * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file - * register access. - * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer. - * during task file register access. - * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA - * xfer. - * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task - * register access. - * 28 UDMA enable - * 29 DMA enable - * 30 PIO_MST enable. if set, the chip is in bus master mode during - * PIO. - * 31 FIFO enable. +/* Key for bus clock timings + * 36x 37x + * bits bits + * 0:3 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA. + * cycles = value + 1 + * 4:7 4:8 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA. + * cycles = value + 1 + * 8:11 9:12 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file + * register access. + * 12:15 13:17 cmd_low_time. Active time of DIOW_/DIOR_ during task file + * register access. + * 16:18 18:20 udma_cycle_time. Clock cycles for UDMA xfer. + * - 21 CLK frequency: 0=ATA clock, 1=dual ATA clock. + * 19:21 22:24 pre_high_time. Time to initialize the 1st cycle for PIO and + * MW DMA xfer. + * 22:24 25:27 cmd_pre_high_time. Time to initialize the 1st PIO cycle for + * task file register access. + * 28 28 UDMA enable. + * 29 29 DMA enable. + * 30 30 PIO MST enable. If set, the chip is in bus master mode during + * PIO xfer. + * 31 31 FIFO enable. */ -static struct chipset_bus_clock_list_entry forty_base_hpt366[] = { - { XFER_UDMA_4, 0x900fd943 }, - { XFER_UDMA_3, 0x900ad943 }, - { XFER_UDMA_2, 0x900bd943 }, - { XFER_UDMA_1, 0x9008d943 }, - { XFER_UDMA_0, 0x9008d943 }, - - { XFER_MW_DMA_2, 0xa008d943 }, - { XFER_MW_DMA_1, 0xa010d955 }, - { XFER_MW_DMA_0, 0xa010d9fc }, - - { XFER_PIO_4, 0xc008d963 }, - { XFER_PIO_3, 0xc010d974 }, - { XFER_PIO_2, 0xc010d997 }, - { XFER_PIO_1, 0xc010d9c7 }, - { XFER_PIO_0, 0xc018d9d9 }, - { 0, 0x0120d9d9 } -}; - -static struct chipset_bus_clock_list_entry thirty_three_base_hpt366[] = { - { XFER_UDMA_4, 0x90c9a731 }, - { XFER_UDMA_3, 0x90cfa731 }, - { XFER_UDMA_2, 0x90caa731 }, - { XFER_UDMA_1, 0x90cba731 }, - { XFER_UDMA_0, 0x90c8a731 }, - - { XFER_MW_DMA_2, 0xa0c8a731 }, - { XFER_MW_DMA_1, 0xa0c8a732 }, /* 0xa0c8a733 */ - { XFER_MW_DMA_0, 0xa0c8a797 }, - - { XFER_PIO_4, 0xc0c8a731 }, - { XFER_PIO_3, 0xc0c8a742 }, - { XFER_PIO_2, 0xc0d0a753 }, - { XFER_PIO_1, 0xc0d0a7a3 }, /* 0xc0d0a793 */ - { XFER_PIO_0, 0xc0d0a7aa }, /* 0xc0d0a7a7 */ - { 0, 0x0120a7a7 } -}; -static struct chipset_bus_clock_list_entry twenty_five_base_hpt366[] = { - { XFER_UDMA_4, 0x90c98521 }, - { XFER_UDMA_3, 0x90cf8521 }, - { XFER_UDMA_2, 0x90cf8521 }, - { XFER_UDMA_1, 0x90cb8521 }, - { XFER_UDMA_0, 0x90cb8521 }, - - { XFER_MW_DMA_2, 0xa0ca8521 }, - { XFER_MW_DMA_1, 0xa0ca8532 }, - { XFER_MW_DMA_0, 0xa0ca8575 }, - - { XFER_PIO_4, 0xc0ca8521 }, - { XFER_PIO_3, 0xc0ca8532 }, - { XFER_PIO_2, 0xc0ca8542 }, - { XFER_PIO_1, 0xc0d08572 }, - { XFER_PIO_0, 0xc0d08585 }, - { 0, 0x01208585 } +static u32 forty_base_hpt36x[] = { + /* XFER_UDMA_6 */ 0x900fd943, + /* XFER_UDMA_5 */ 0x900fd943, + /* XFER_UDMA_4 */ 0x900fd943, + /* XFER_UDMA_3 */ 0x900ad943, + /* XFER_UDMA_2 */ 0x900bd943, + /* XFER_UDMA_1 */ 0x9008d943, + /* XFER_UDMA_0 */ 0x9008d943, + + /* XFER_MW_DMA_2 */ 0xa008d943, + /* XFER_MW_DMA_1 */ 0xa010d955, + /* XFER_MW_DMA_0 */ 0xa010d9fc, + + /* XFER_PIO_4 */ 0xc008d963, + /* XFER_PIO_3 */ 0xc010d974, + /* XFER_PIO_2 */ 0xc010d997, + /* XFER_PIO_1 */ 0xc010d9c7, + /* XFER_PIO_0 */ 0xc018d9d9 }; -/* from highpoint documentation. these are old values */ -static struct chipset_bus_clock_list_entry thirty_three_base_hpt370[] = { -/* { XFER_UDMA_5, 0x1A85F442, 0x16454e31 }, */ - { XFER_UDMA_5, 0x16454e31 }, - { XFER_UDMA_4, 0x16454e31 }, - { XFER_UDMA_3, 0x166d4e31 }, - { XFER_UDMA_2, 0x16494e31 }, - { XFER_UDMA_1, 0x164d4e31 }, - { XFER_UDMA_0, 0x16514e31 }, - - { XFER_MW_DMA_2, 0x26514e21 }, - { XFER_MW_DMA_1, 0x26514e33 }, - { XFER_MW_DMA_0, 0x26514e97 }, - - { XFER_PIO_4, 0x06514e21 }, - { XFER_PIO_3, 0x06514e22 }, - { XFER_PIO_2, 0x06514e33 }, - { XFER_PIO_1, 0x06914e43 }, - { XFER_PIO_0, 0x06914e57 }, - { 0, 0x06514e57 } +static u32 thirty_three_base_hpt36x[] = { + /* XFER_UDMA_6 */ 0x90c9a731, + /* XFER_UDMA_5 */ 0x90c9a731, + /* XFER_UDMA_4 */ 0x90c9a731, + /* XFER_UDMA_3 */ 0x90cfa731, + /* XFER_UDMA_2 */ 0x90caa731, + /* XFER_UDMA_1 */ 0x90cba731, + /* XFER_UDMA_0 */ 0x90c8a731, + + /* XFER_MW_DMA_2 */ 0xa0c8a731, + /* XFER_MW_DMA_1 */ 0xa0c8a732, /* 0xa0c8a733 */ + /* XFER_MW_DMA_0 */ 0xa0c8a797, + + /* XFER_PIO_4 */ 0xc0c8a731, + /* XFER_PIO_3 */ 0xc0c8a742, + /* XFER_PIO_2 */ 0xc0d0a753, + /* XFER_PIO_1 */ 0xc0d0a7a3, /* 0xc0d0a793 */ + /* XFER_PIO_0 */ 0xc0d0a7aa /* 0xc0d0a7a7 */ }; -/* these are the current (4 sep 2001) timings from highpoint */ -static struct chipset_bus_clock_list_entry thirty_three_base_hpt370a[] = { - { XFER_UDMA_5, 0x12446231 }, - { XFER_UDMA_4, 0x12446231 }, - { XFER_UDMA_3, 0x126c6231 }, - { XFER_UDMA_2, 0x12486231 }, - { XFER_UDMA_1, 0x124c6233 }, - { XFER_UDMA_0, 0x12506297 }, - - { XFER_MW_DMA_2, 0x22406c31 }, - { XFER_MW_DMA_1, 0x22406c33 }, - { XFER_MW_DMA_0, 0x22406c97 }, - - { XFER_PIO_4, 0x06414e31 }, - { XFER_PIO_3, 0x06414e42 }, - { XFER_PIO_2, 0x06414e53 }, - { XFER_PIO_1, 0x06814e93 }, - { XFER_PIO_0, 0x06814ea7 }, - { 0, 0x06814ea7 } +static u32 twenty_five_base_hpt36x[] = { + /* XFER_UDMA_6 */ 0x90c98521, + /* XFER_UDMA_5 */ 0x90c98521, + /* XFER_UDMA_4 */ 0x90c98521, + /* XFER_UDMA_3 */ 0x90cf8521, + /* XFER_UDMA_2 */ 0x90cf8521, + /* XFER_UDMA_1 */ 0x90cb8521, + /* XFER_UDMA_0 */ 0x90cb8521, + + /* XFER_MW_DMA_2 */ 0xa0ca8521, + /* XFER_MW_DMA_1 */ 0xa0ca8532, + /* XFER_MW_DMA_0 */ 0xa0ca8575, + + /* XFER_PIO_4 */ 0xc0ca8521, + /* XFER_PIO_3 */ 0xc0ca8532, + /* XFER_PIO_2 */ 0xc0ca8542, + /* XFER_PIO_1 */ 0xc0d08572, + /* XFER_PIO_0 */ 0xc0d08585 }; -static struct chipset_bus_clock_list_entry fifty_base_hpt370a[] = { - { XFER_UDMA_5, 0x12848242 }, - { XFER_UDMA_4, 0x12ac8242 }, - { XFER_UDMA_3, 0x128c8242 }, - { XFER_UDMA_2, 0x120c8242 }, - { XFER_UDMA_1, 0x12148254 }, - { XFER_UDMA_0, 0x121882ea }, - - { XFER_MW_DMA_2, 0x22808242 }, - { XFER_MW_DMA_1, 0x22808254 }, - { XFER_MW_DMA_0, 0x228082ea }, - - { XFER_PIO_4, 0x0a81f442 }, - { XFER_PIO_3, 0x0a81f443 }, - { XFER_PIO_2, 0x0a81f454 }, - { XFER_PIO_1, 0x0ac1f465 }, - { XFER_PIO_0, 0x0ac1f48a }, - { 0, 0x0ac1f48a } +static u32 thirty_three_base_hpt37x[] = { + /* XFER_UDMA_6 */ 0x12446231, /* 0x12646231 ?? */ + /* XFER_UDMA_5 */ 0x12446231, + /* XFER_UDMA_4 */ 0x12446231, + /* XFER_UDMA_3 */ 0x126c6231, + /* XFER_UDMA_2 */ 0x12486231, + /* XFER_UDMA_1 */ 0x124c6233, + /* XFER_UDMA_0 */ 0x12506297, + + /* XFER_MW_DMA_2 */ 0x22406c31, + /* XFER_MW_DMA_1 */ 0x22406c33, + /* XFER_MW_DMA_0 */ 0x22406c97, + + /* XFER_PIO_4 */ 0x06414e31, + /* XFER_PIO_3 */ 0x06414e42, + /* XFER_PIO_2 */ 0x06414e53, + /* XFER_PIO_1 */ 0x06814e93, + /* XFER_PIO_0 */ 0x06814ea7 }; -static struct chipset_bus_clock_list_entry thirty_three_base_hpt372[] = { - { XFER_UDMA_6, 0x12446231 }, /* 0x12646231 ?? */ - { XFER_UDMA_5, 0x12446231 }, - { XFER_UDMA_4, 0x12446231 }, - { XFER_UDMA_3, 0x126c6231 }, - { XFER_UDMA_2, 0x12486231 }, - { XFER_UDMA_1, 0x124c6233 }, - { XFER_UDMA_0, 0x12506297 }, - - { XFER_MW_DMA_2, 0x22406c31 }, - { XFER_MW_DMA_1, 0x22406c33 }, - { XFER_MW_DMA_0, 0x22406c97 }, - - { XFER_PIO_4, 0x06414e31 }, - { XFER_PIO_3, 0x06414e42 }, - { XFER_PIO_2, 0x06414e53 }, - { XFER_PIO_1, 0x06814e93 }, - { XFER_PIO_0, 0x06814ea7 }, - { 0, 0x06814ea7 } +static u32 fifty_base_hpt37x[] = { + /* XFER_UDMA_6 */ 0x12848242, + /* XFER_UDMA_5 */ 0x12848242, + /* XFER_UDMA_4 */ 0x12ac8242, + /* XFER_UDMA_3 */ 0x128c8242, + /* XFER_UDMA_2 */ 0x120c8242, + /* XFER_UDMA_1 */ 0x12148254, + /* XFER_UDMA_0 */ 0x121882ea, + + /* XFER_MW_DMA_2 */ 0x22808242, + /* XFER_MW_DMA_1 */ 0x22808254, + /* XFER_MW_DMA_0 */ 0x228082ea, + + /* XFER_PIO_4 */ 0x0a81f442, + /* XFER_PIO_3 */ 0x0a81f443, + /* XFER_PIO_2 */ 0x0a81f454, + /* XFER_PIO_1 */ 0x0ac1f465, + /* XFER_PIO_0 */ 0x0ac1f48a }; -static struct chipset_bus_clock_list_entry fifty_base_hpt372[] = { - { XFER_UDMA_6, 0x12848242 }, - { XFER_UDMA_5, 0x12848242 }, - { XFER_UDMA_4, 0x12ac8242 }, - { XFER_UDMA_3, 0x128c8242 }, - { XFER_UDMA_2, 0x120c8242 }, - { XFER_UDMA_1, 0x12148254 }, - { XFER_UDMA_0, 0x121882ea }, - - { XFER_MW_DMA_2, 0x22808242 }, - { XFER_MW_DMA_1, 0x22808254 }, - { XFER_MW_DMA_0, 0x228082ea }, - - { XFER_PIO_4, 0x0a81f442 }, - { XFER_PIO_3, 0x0a81f443 }, - { XFER_PIO_2, 0x0a81f454 }, - { XFER_PIO_1, 0x0ac1f465 }, - { XFER_PIO_0, 0x0ac1f48a }, - { 0, 0x0a81f443 } -}; - -static struct chipset_bus_clock_list_entry sixty_six_base_hpt372[] = { - { XFER_UDMA_6, 0x1c869c62 }, - { XFER_UDMA_5, 0x1cae9c62 }, /* 0x1c8a9c62 */ - { XFER_UDMA_4, 0x1c8a9c62 }, - { XFER_UDMA_3, 0x1c8e9c62 }, - { XFER_UDMA_2, 0x1c929c62 }, - { XFER_UDMA_1, 0x1c9a9c62 }, - { XFER_UDMA_0, 0x1c829c62 }, - - { XFER_MW_DMA_2, 0x2c829c62 }, - { XFER_MW_DMA_1, 0x2c829c66 }, - { XFER_MW_DMA_0, 0x2c829d2e }, - - { XFER_PIO_4, 0x0c829c62 }, - { XFER_PIO_3, 0x0c829c84 }, - { XFER_PIO_2, 0x0c829ca6 }, - { XFER_PIO_1, 0x0d029d26 }, - { XFER_PIO_0, 0x0d029d5e }, - { 0, 0x0d029d26 } +static u32 sixty_six_base_hpt37x[] = { + /* XFER_UDMA_6 */ 0x1c869c62, + /* XFER_UDMA_5 */ 0x1cae9c62, /* 0x1c8a9c62 */ + /* XFER_UDMA_4 */ 0x1c8a9c62, + /* XFER_UDMA_3 */ 0x1c8e9c62, + /* XFER_UDMA_2 */ 0x1c929c62, + /* XFER_UDMA_1 */ 0x1c9a9c62, + /* XFER_UDMA_0 */ 0x1c829c62, + + /* XFER_MW_DMA_2 */ 0x2c829c62, + /* XFER_MW_DMA_1 */ 0x2c829c66, + /* XFER_MW_DMA_0 */ 0x2c829d2e, + + /* XFER_PIO_4 */ 0x0c829c62, + /* XFER_PIO_3 */ 0x0c829c84, + /* XFER_PIO_2 */ 0x0c829ca6, + /* XFER_PIO_1 */ 0x0d029d26, + /* XFER_PIO_0 */ 0x0d029d5e }; #define HPT366_DEBUG_DRIVE_INFO 0 @@ -401,7 +354,7 @@ struct hpt_info #define IS_3xxN 2 #define PCI_66MHZ 4 /* Speed table */ - struct chipset_bus_clock_list_entry *speed; + u32 *speed; }; /* @@ -538,12 +491,20 @@ static int check_in_drive_lists (ide_drive_t *drive, const char **list) return 0; } -static unsigned int pci_bus_clock_list (u8 speed, struct chipset_bus_clock_list_entry * chipset_table) +static u32 pci_bus_clock_list(u8 speed, u32 *chipset_table) { - for ( ; chipset_table->xfer_speed ; chipset_table++) - if (chipset_table->xfer_speed == speed) - return chipset_table->chipset_settings; - return chipset_table->chipset_settings; + int i; + + /* + * Lookup the transfer mode table to get the index into + * the timing table. + * + * NOTE: For XFER_PIO_SLOW, PIO mode 0 timings will be used. + */ + for (i = 0; i < ARRAY_SIZE(xfer_speeds) - 1; i++) + if (xfer_speeds[i] == speed) + break; + return chipset_table[i]; } static int hpt36x_tune_chipset(ide_drive_t *drive, u8 xferspeed) @@ -1061,14 +1022,14 @@ static void __devinit hpt366_clocking(ide_hwif_t *hwif) /* detect bus speed by looking at control reg timing: */ switch((reg1 >> 8) & 7) { case 5: - info->speed = forty_base_hpt366; + info->speed = forty_base_hpt36x; break; case 9: - info->speed = twenty_five_base_hpt366; + info->speed = twenty_five_base_hpt36x; break; case 7: default: - info->speed = thirty_three_base_hpt366; + info->speed = thirty_three_base_hpt36x; break; } } @@ -1131,27 +1092,16 @@ static void __devinit hpt37x_clocking(ide_hwif_t *hwif) pll = F_LOW_PCI_66; if (pll == F_LOW_PCI_33) { - if (info->revision >= 5) - info->speed = thirty_three_base_hpt372; - else if (info->revision >= 4) - info->speed = thirty_three_base_hpt370a; - else - info->speed = thirty_three_base_hpt370; + info->speed = thirty_three_base_hpt37x; printk(KERN_DEBUG "HPT37X: using 33MHz PCI clock\n"); } else if (pll == F_LOW_PCI_40) { /* Unsupported */ } else if (pll == F_LOW_PCI_50) { - if (info->revision >= 5) - info->speed = fifty_base_hpt372; - else - info->speed = fifty_base_hpt370a; + info->speed = fifty_base_hpt37x; printk(KERN_DEBUG "HPT37X: using 50MHz PCI clock\n"); } else { - if (info->revision >= 5) { - info->speed = sixty_six_base_hpt372; - printk(KERN_DEBUG "HPT37X: using 66MHz PCI clock\n"); - } else - printk(KERN_ERR "HPT37x: 66MHz timings not supported.\n"); + info->speed = sixty_six_base_hpt37x; + printk(KERN_DEBUG "HPT37X: using 66MHz PCI clock\n"); } } @@ -1201,14 +1151,8 @@ static void __devinit hpt37x_clocking(ide_hwif_t *hwif) pci_write_config_dword(dev, 0x5c, pll & ~0x100); pci_write_config_byte(dev, 0x5b, 0x21); - if (info->revision >= 8) - info->speed = fifty_base_hpt370a; - else if (info->revision >= 5) - info->speed = fifty_base_hpt372; - else if (info->revision >= 4) - info->speed = fifty_base_hpt370a; - else - info->speed = fifty_base_hpt370a; + + info->speed = fifty_base_hpt37x; printk("HPT37X: using 50MHz internal PLL\n"); goto init_hpt37X_done; } |
