diff options
| -rw-r--r-- | Documentation/ABI/testing/sysfs-driver-hid-picolcd | 17 | ||||
| -rw-r--r-- | drivers/hid/Kconfig | 18 | ||||
| -rw-r--r-- | drivers/hid/Makefile | 1 | ||||
| -rw-r--r-- | drivers/hid/hid-core.c | 2 | ||||
| -rw-r--r-- | drivers/hid/hid-ids.h | 2 | ||||
| -rw-r--r-- | drivers/hid/hid-picolcd.c | 1183 |
6 files changed, 1223 insertions, 0 deletions
diff --git a/Documentation/ABI/testing/sysfs-driver-hid-picolcd b/Documentation/ABI/testing/sysfs-driver-hid-picolcd new file mode 100644 index 000000000000..6fb4f21469f7 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-driver-hid-picolcd @@ -0,0 +1,17 @@ +What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/operation_mode +Date: March 2010 +Contact: Bruno Prémont <bonbons@linux-vserver.org> +Description: Make it possible to switch the PicoLCD device between LCD + (firmware) and bootloader (flasher) operation modes. + + Reading: returns list of available modes, the active mode being + enclosed in brackets ('[' and ']') + + Writing: causes operation mode switch. Permitted values are + the non-active mode names listed when read, optionally followed + by a delay value expressed in ms. + + Note: when switching mode the current PicoLCD HID device gets + disconnected and reconnects after above delay (default value + is 5 seconds though this default should not be relied on). + diff --git a/drivers/hid/Kconfig b/drivers/hid/Kconfig index 71d4c0703629..138ba6a277ee 100644 --- a/drivers/hid/Kconfig +++ b/drivers/hid/Kconfig @@ -262,6 +262,24 @@ config HID_PETALYNX ---help--- Support for Petalynx Maxter remote control. +config HID_PICOLCD + tristate "PicoLCD (graphic version)" + depends on USB_HID + ---help--- + This provides support for Minibox PicoLCD devices, currently + only the graphical ones are supported. + + This includes support for the following device features: + - Keypad + - Switching between Firmware and Flash mode + Features that are not (yet) supported: + - Framebuffer for monochrome 256x64 display + - Backlight control + - Contrast control + - IR + - General purpose outputs + - EEProm / Flash access + config HID_QUANTA tristate "Quanta Optical Touch" depends on USB_HID diff --git a/drivers/hid/Makefile b/drivers/hid/Makefile index 0b2618f092ca..7fd1614e7e2c 100644 --- a/drivers/hid/Makefile +++ b/drivers/hid/Makefile @@ -44,6 +44,7 @@ obj-$(CONFIG_HID_ORTEK) += hid-ortek.o obj-$(CONFIG_HID_QUANTA) += hid-quanta.o obj-$(CONFIG_HID_PANTHERLORD) += hid-pl.o obj-$(CONFIG_HID_PETALYNX) += hid-petalynx.o +obj-$(CONFIG_HID_PICOLCD) += hid-picolcd.o obj-$(CONFIG_HID_SAMSUNG) += hid-samsung.o obj-$(CONFIG_HID_SMARTJOYPLUS) += hid-sjoy.o obj-$(CONFIG_HID_SONY) += hid-sony.o diff --git a/drivers/hid/hid-core.c b/drivers/hid/hid-core.c index 2e2aa759d230..bb11fb460d55 100644 --- a/drivers/hid/hid-core.c +++ b/drivers/hid/hid-core.c @@ -1335,6 +1335,8 @@ static const struct hid_device_id hid_blacklist[] = { { HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_LOGITECH_RUMBLEPAD2) }, { HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_SPACETRAVELLER) }, { HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_SPACENAVIGATOR) }, + { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD) }, + { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD_BOOTLOADER) }, { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_SIDEWINDER_GV) }, { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_NE4K) }, { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_LK6K) }, diff --git a/drivers/hid/hid-ids.h b/drivers/hid/hid-ids.h index 797e06470356..783b41d8592e 100644 --- a/drivers/hid/hid-ids.h +++ b/drivers/hid/hid-ids.h @@ -341,6 +341,8 @@ #define USB_VENDOR_ID_MICROCHIP 0x04d8 #define USB_DEVICE_ID_PICKIT1 0x0032 #define USB_DEVICE_ID_PICKIT2 0x0033 +#define USB_DEVICE_ID_PICOLCD 0xc002 +#define USB_DEVICE_ID_PICOLCD_BOOTLOADER 0xf002 #define USB_VENDOR_ID_MICROSOFT 0x045e #define USB_DEVICE_ID_SIDEWINDER_GV 0x003b diff --git a/drivers/hid/hid-picolcd.c b/drivers/hid/hid-picolcd.c new file mode 100644 index 000000000000..c7855f388898 --- /dev/null +++ b/drivers/hid/hid-picolcd.c @@ -0,0 +1,1183 @@ +/*************************************************************************** + * Copyright (C) 2010 by Bruno Prémont <bonbons@linux-vserver.org> * + * * + * Based on Logitech G13 driver (v0.4) * + * Copyright (C) 2009 by Rick L. Vinyard, Jr. <rvinyard@cs.nmsu.edu> * + * * + * This program is free software: you can redistribute it and/or modify * + * it under the terms of the GNU General Public License as published by * + * the Free Software Foundation, version 2 of the License. * + * * + * This driver is distributed in the hope that it will be useful, but * + * WITHOUT ANY WARRANTY; without even the implied warranty of * + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU * + * General Public License for more details. * + * * + * You should have received a copy of the GNU General Public License * + * along with this software. If not see <http://www.gnu.org/licenses/>. * + ***************************************************************************/ + +#include <linux/hid.h> +#include <linux/hid-debug.h> +#include <linux/input.h> +#include "hid-ids.h" +#include "usbhid/usbhid.h" +#include <linux/usb.h> + +#include <linux/seq_file.h> +#include <linux/debugfs.h> + +#include <linux/completion.h> + +#define PICOLCD_NAME "PicoLCD (graphic)" + +/* Report numbers */ +#define REPORT_ERROR_CODE 0x10 /* LCD: IN[16] */ +#define ERR_SUCCESS 0x00 +#define ERR_PARAMETER_MISSING 0x01 +#define ERR_DATA_MISSING 0x02 +#define ERR_BLOCK_READ_ONLY 0x03 +#define ERR_BLOCK_NOT_ERASABLE 0x04 +#define ERR_BLOCK_TOO_BIG 0x05 +#define ERR_SECTION_OVERFLOW 0x06 +#define ERR_INVALID_CMD_LEN 0x07 +#define ERR_INVALID_DATA_LEN 0x08 +#define REPORT_KEY_STATE 0x11 /* LCD: IN[2] */ +#define REPORT_IR_DATA 0x21 /* LCD: IN[63] */ +#define REPORT_EE_DATA 0x32 /* LCD: IN[63] */ +#define REPORT_MEMORY 0x41 /* LCD: IN[63] */ +#define REPORT_LED_STATE 0x81 /* LCD: OUT[1] */ +#define REPORT_BRIGHTNESS 0x91 /* LCD: OUT[1] */ +#define REPORT_CONTRAST 0x92 /* LCD: OUT[1] */ +#define REPORT_RESET 0x93 /* LCD: OUT[2] */ +#define REPORT_LCD_CMD 0x94 /* LCD: OUT[63] */ +#define REPORT_LCD_DATA 0x95 /* LCD: OUT[63] */ +#define REPORT_LCD_CMD_DATA 0x96 /* LCD: OUT[63] */ +#define REPORT_EE_READ 0xa3 /* LCD: OUT[63] */ +#define REPORT_EE_WRITE 0xa4 /* LCD: OUT[63] */ +#define REPORT_ERASE_MEMORY 0xb2 /* LCD: OUT[2] */ +#define REPORT_READ_MEMORY 0xb3 /* LCD: OUT[3] */ +#define REPORT_WRITE_MEMORY 0xb4 /* LCD: OUT[63] */ +#define REPORT_SPLASH_RESTART 0xc1 /* LCD: OUT[1] */ +#define REPORT_EXIT_KEYBOARD 0xef /* LCD: OUT[2] */ +#define REPORT_VERSION 0xf1 /* LCD: IN[2],OUT[1] Bootloader: IN[2],OUT[1] */ +#define REPORT_BL_ERASE_MEMORY 0xf2 /* Bootloader: IN[36],OUT[4] */ +#define REPORT_BL_READ_MEMORY 0xf3 /* Bootloader: IN[36],OUT[4] */ +#define REPORT_BL_WRITE_MEMORY 0xf4 /* Bootloader: IN[36],OUT[36] */ +#define REPORT_DEVID 0xf5 /* LCD: IN[5], OUT[1] Bootloader: IN[5],OUT[1] */ +#define REPORT_SPLASH_SIZE 0xf6 /* LCD: IN[4], OUT[1] */ +#define REPORT_HOOK_VERSION 0xf7 /* LCD: IN[2], OUT[1] */ +#define REPORT_EXIT_FLASHER 0xff /* Bootloader: OUT[2] */ + +/* Input device + * + * The PicoLCD has an IR receiver header, a built-in keypad with 5 keys + * and header for 4x4 key matrix. The built-in keys are part of the matrix. + */ +static const unsigned short def_keymap[] = { + KEY_RESERVED, /* none */ + KEY_BACK, /* col 4 + row 1 */ + KEY_HOMEPAGE, /* col 3 + row 1 */ + KEY_RESERVED, /* col 2 + row 1 */ + KEY_RESERVED, /* col 1 + row 1 */ + KEY_SCROLLUP, /* col 4 + row 2 */ + KEY_OK, /* col 3 + row 2 */ + KEY_SCROLLDOWN, /* col 2 + row 2 */ + KEY_RESERVED, /* col 1 + row 2 */ + KEY_RESERVED, /* col 4 + row 3 */ + KEY_RESERVED, /* col 3 + row 3 */ + KEY_RESERVED, /* col 2 + row 3 */ + KEY_RESERVED, /* col 1 + row 3 */ + KEY_RESERVED, /* col 4 + row 4 */ + KEY_RESERVED, /* col 3 + row 4 */ + KEY_RESERVED, /* col 2 + row 4 */ + KEY_RESERVED, /* col 1 + row 4 */ +}; +#define PICOLCD_KEYS ARRAY_SIZE(def_keymap) + +/* Description of in-progress IO operation, used for operations + * that trigger response from device */ +struct picolcd_pending { + struct hid_report *out_report; + struct hid_report *in_report; + struct completion ready; + int raw_size; + u8 raw_data[64]; +}; + +/* Per device data structure */ +struct picolcd_data { + struct hid_device *hdev; +#ifdef CONFIG_DEBUG_FS + int addr_sz; +#endif + u8 version[2]; + /* input stuff */ + u8 pressed_keys[2]; + struct input_dev *input_keys; + struct input_dev *input_cir; + unsigned short keycode[PICOLCD_KEYS]; + + /* Housekeeping stuff */ + spinlock_t lock; + struct mutex mutex; + struct picolcd_pending *pending; + int status; +#define PICOLCD_BOOTLOADER 1 +#define PICOLCD_FAILED 2 +}; + + +/* Find a given report */ +#define picolcd_in_report(id, dev) picolcd_report(id, dev, HID_INPUT_REPORT) +#define picolcd_out_report(id, dev) picolcd_report(id, dev, HID_OUTPUT_REPORT) + +static struct hid_report *picolcd_report(int id, struct hid_device *hdev, int dir) +{ + struct list_head *feature_report_list = &hdev->report_enum[dir].report_list; + struct hid_report *report = NULL; + + list_for_each_entry(report, feature_report_list, list) { + if (report->id == id) + return report; + } + dev_warn(&hdev->dev, "No report with id 0x%x found\n", id); + return NULL; +} + +#ifdef CONFIG_DEBUG_FS +static void picolcd_debug_out_report(struct picolcd_data *data, + struct hid_device *hdev, struct hid_report *report); +#define usbhid_submit_report(a, b, c) \ + do { \ + picolcd_debug_out_report(hid_get_drvdata(a), a, b); \ + usbhid_submit_report(a, b, c); \ + } while (0) +#endif + +/* Submit a report and wait for a reply from device - if device fades away + * or does not respond in time, return NULL */ +static struct picolcd_pending *picolcd_send_and_wait(struct hid_device *hdev, + int report_id, const u8 *raw_data, int size) +{ + struct picolcd_data *data = hid_get_drvdata(hdev); + struct picolcd_pending *work; + struct hid_report *report = picolcd_out_report(report_id, hdev); + unsigned long flags; + int i, j, k; + + if (!report || !data) + return NULL; + if (data->status & PICOLCD_FAILED) + return NULL; + work = kzalloc(sizeof(*work), GFP_KERNEL); + if (!work) + return NULL; + + init_completion(&work->ready); + work->out_report = report; + work->in_report = NULL; + work->raw_size = 0; + + mutex_lock(&data->mutex); + spin_lock_irqsave(&data->lock, flags); + for (i = k = 0; i < report->maxfield; i++) + for (j = 0; j < report->field[i]->report_count; j++) { + hid_set_field(report->field[i], j, k < size ? raw_data[k] : 0); + k++; + } + data->pending = work; + usbhid_submit_report(data->hdev, report, USB_DIR_OUT); + spin_unlock_irqrestore(&data->lock, flags); + wait_for_completion_interruptible_timeout(&work->ready, HZ*2); + spin_lock_irqsave(&data->lock, flags); + data->pending = NULL; + spin_unlock_irqrestore(&data->lock, flags); + mutex_unlock(&data->mutex); + return work; +} + +/* + * input class device + */ +static int picolcd_raw_keypad(struct picolcd_data *data, + struct hid_report *report, u8 *raw_data, int size) +{ + /* + * Keypad event + * First and second data bytes list currently pressed keys, + * 0x00 means no key and at most 2 keys may be pressed at same time + */ + int i, j; + + /* determine newly pressed keys */ + for (i = 0; i < size; i++) { + unsigned int key_code; + if (raw_data[i] == 0) + continue; + for (j = 0; j < sizeof(data->pressed_keys); j++) + if (data->pressed_keys[j] == raw_data[i]) + goto key_already_down; + for (j = 0; j < sizeof(data->pressed_keys); j++) + if (data->pressed_keys[j] == 0) { + data->pressed_keys[j] = raw_data[i]; + break; + } + input_event(data->input_keys, EV_MSC, MSC_SCAN, raw_data[i]); + if (raw_data[i] < PICOLCD_KEYS) + key_code = data->keycode[raw_data[i]]; + else + key_code = KEY_UNKNOWN; + if (key_code != KEY_UNKNOWN) { + dbg_hid(PICOLCD_NAME " got key press for %u:%d", + raw_data[i], key_code); + input_report_key(data->input_keys, key_code, 1); + } + input_sync(data->input_keys); +key_already_down: + continue; + } + + /* determine newly released keys */ + for (j = 0; j < sizeof(data->pressed_keys); j++) { + unsigned int key_code; + if (data->pressed_keys[j] == 0) + continue; + for (i = 0; i < size; i++) + if (data->pressed_keys[j] == raw_data[i]) + goto key_still_down; + input_event(data->input_keys, EV_MSC, MSC_SCAN, data->pressed_keys[j]); + if (data->pressed_keys[j] < PICOLCD_KEYS) + key_code = data->keycode[data->pressed_keys[j]]; + else + key_code = KEY_UNKNOWN; + if (key_code != KEY_UNKNOWN) { + dbg_hid(PICOLCD_NAME " got key release for %u:%d", + data->pressed_keys[j], key_code); + input_report_key(data->input_keys, key_code, 0); + } + input_sync(data->input_keys); + data->pressed_keys[j] = 0; +key_still_down: + continue; + } + return 1; +} + +static int picolcd_raw_cir(struct picolcd_data *data, + struct hid_report *report, u8 *raw_data, int size) +{ + /* Need understanding of CIR data format to implement ... */ + return 1; +} + +static int picolcd_check_version(struct hid_device *hdev) +{ + struct picolcd_data *data = hid_get_drvdata(hdev); + struct picolcd_pending *verinfo; + int ret = 0; + + if (!data) + return -ENODEV; + + verinfo = picolcd_send_and_wait(hdev, REPORT_VERSION, NULL, 0); + if (!verinfo) { + dev_err(&hdev->dev, "no version response from PicoLCD"); + return -ENODEV; + } + + if (verinfo->raw_size == 2) { + if (data->status & PICOLCD_BOOTLOADER) { + dev_info(&hdev->dev, "PicoLCD, bootloader version %d.%d\n", + verinfo->raw_data[0], verinfo->raw_data[1]); + data->version[0] = verinfo->raw_data[0]; + data->version[1] = verinfo->raw_data[1]; + } else { + dev_info(&hdev->dev, "PicoLCD, firmware version %d.%d\n", + verinfo->raw_data[1], verinfo->raw_data[0]); + data->version[0] = verinfo->raw_data[1]; + data->version[1] = verinfo->raw_data[0]; + } + } else { + dev_err(&hdev->dev, "confused, got unexpected version response from PicoLCD\n"); + ret = -EINVAL; + } + kfree(verinfo); + return ret; +} + +/* + * Reset our device and wait for answer to VERSION request + */ +static int picolcd_reset(struct hid_device *hdev) +{ + struct picolcd_data *data = hid_get_drvdata(hdev); + struct hid_report *report = picolcd_out_report(REPORT_RESET, hdev); + unsigned long flags; + + if (!data || !report || report->maxfield != 1) + return -ENODEV; + + spin_lock_irqsave(&data->lock, flags); + if (hdev->product == USB_DEVICE_ID_PICOLCD_BOOTLOADER) + data->status |= PICOLCD_BOOTLOADER; + + /* perform the reset */ + hid_set_field(report->field[0], 0, 1); + usbhid_submit_report(hdev, report, USB_DIR_OUT); + spin_unlock_irqrestore(&data->lock, flags); + + return picolcd_check_version(hdev); +} + +/* + * The "operation_mode" sysfs attribute + */ +static ssize_t picolcd_operation_mode_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct picolcd_data *data = dev_get_drvdata(dev); + + if (data->status & PICOLCD_BOOTLOADER) + return snprintf(buf, PAGE_SIZE, "[bootloader] lcd\n"); + else + return snprintf(buf, PAGE_SIZE, "bootloader [lcd]\n"); +} + +static ssize_t picolcd_operation_mode_store(struct device *dev, + struct device_attribute *attr, const char *buf, size_t count) +{ + struct picolcd_data *data = dev_get_drvdata(dev); + struct hid_report *report = NULL; + size_t cnt = count; + int timeout = 5000; + unsigned u; + unsigned long flags; + + if (cnt >= 3 && strncmp("lcd", buf, 3) == 0) { + if (data->status & PICOLCD_BOOTLOADER) + report = picolcd_out_report(REPORT_EXIT_FLASHER, data->hdev); + buf += 3; + cnt -= 3; + } else if (cnt >= 10 && strncmp("bootloader", buf, 10) == 0) { + if (!(data->status & PICOLCD_BOOTLOADER)) + report = picolcd_out_report(REPORT_EXIT_KEYBOARD, data->hdev); + buf += 10; + cnt -= 10; + } + if (!report) + return -EINVAL; + + while (cnt > 0 && (*buf == ' ' || *buf == '\t')) { + buf++; + cnt--; + } + while (cnt > 0 && (buf[cnt-1] == '\n' || buf[cnt-1] == '\r')) + cnt--; + if (cnt > 0) { + if (sscanf(buf, "%u", &u) != 1) + return -EINVAL; + if (u > 30000) + return -EINVAL; + else + timeout = u; + } + + spin_lock_irqsave(&data->lock, flags); + hid_set_field(report->field[0], 0, timeout & 0xff); + hid_set_field(report->field[0], 1, (timeout >> 8) & 0xff); + usbhid_submit_report(data->hdev, report, USB_DIR_OUT); + spin_unlock_irqrestore(&data->lock, flags); + return count; +} + +static DEVICE_ATTR(operation_mode, 0644, picolcd_operation_mode_show, + picolcd_operation_mode_store); + + +#ifdef CONFIG_DEBUG_FS +/* + * Helper code for HID report level dumping/debugging + */ +static const char *error_codes[] = { + "success", "parameter missing", "data_missing", "block readonly", + "block not erasable", "block too big", "section overflow", + "invalid command length", "invalid data length", +}; + +static void dump_buff_as_hex(char *dst, size_t dst_sz, const u8 *data, + const size_t data_len) +{ + int i, j; + for (i = j = 0; i < data_len && j + 3 < dst_sz; i++) { + dst[j++] = hex_asc[(data[i] >> 4) & 0x0f]; + dst[j++] = hex_asc[data[i] & 0x0f]; + dst[j++] = ' '; + } + if (j < dst_sz) { + dst[j--] = '\0'; + dst[j] = '\n'; + } else + dst[j] = '\0'; +} + +static void picolcd_debug_out_report(struct picolcd_data *data, + struct hid_device *hdev, struct hid_report *report) +{ + u8 raw_data[70]; + int raw_size = (report->size >> 3) + 1; + char *buff; +#define BUFF_SZ 256 + + /* Avoid unnecessary overhead if debugfs is disabled */ + if (!hdev->debug_events) + return; + + buff = kmalloc(BUFF_SZ, GFP_ATOMIC); + if (!buff) + return; + + snprintf(buff, BUFF_SZ, "\nout report %d (size %d) = ", + report->id, raw_size); + hid_debug_event(hdev, buff); + if (raw_size + 5 > sizeof(raw_data)) { + hid_debug_event(hdev, " TOO BIG\n"); + return; + } else { + raw_data[0] = report->id; + hid_output_report(report, raw_data); + dump_buff_as_hex(buff, BUFF_SZ, raw_data, raw_size); + hid_debug_event(hdev, buff); + } + + switch (report->id) { + case REPORT_LED_STATE: + /* 1 data byte with GPO state */ + snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n", + "REPORT_LED_STATE", report->id, raw_size-1); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tGPO state: 0x%02x\n", raw_data[1]); + hid_debug_event(hdev, buff); + break; + case REPORT_BRIGHTNESS: + /* 1 data byte with brightness */ + snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n", + "REPORT_BRIGHTNESS", report->id, raw_size-1); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tBrightness: 0x%02x\n", raw_data[1]); + hid_debug_event(hdev, buff); + break; + case REPORT_CONTRAST: + /* 1 data byte with contrast */ + snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n", + "REPORT_CONTRAST", report->id, raw_size-1); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tContrast: 0x%02x\n", raw_data[1]); + hid_debug_event(hdev, buff); + break; + case REPORT_RESET: + /* 2 data bytes with reset duration in ms */ + snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n", + "REPORT_RESET", report->id, raw_size-1); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tDuration: 0x%02x%02x (%dms)\n", + raw_data[2], raw_data[1], raw_data[2] << 8 | raw_data[1]); + hid_debug_event(hdev, buff); + break; + case REPORT_LCD_CMD: + /* 63 data bytes with LCD commands */ + snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n", + "REPORT_LCD_CMD", report->id, raw_size-1); + hid_debug_event(hdev, buff); + /* TODO: format decoding */ + break; + case REPORT_LCD_DATA: + /* 63 data bytes with LCD data */ + snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n", + "REPORT_LCD_CMD", report->id, raw_size-1); + /* TODO: format decoding */ + hid_debug_event(hdev, buff); + break; + case REPORT_LCD_CMD_DATA: + /* 63 data bytes with LCD commands and data */ + snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n", + "REPORT_LCD_CMD", report->id, raw_size-1); + /* TODO: format decoding */ + hid_debug_event(hdev, buff); + break; + case REPORT_EE_READ: + /* 3 data bytes with read area description */ + snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n", + "REPORT_EE_READ", report->id, raw_size-1); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n", + raw_data[2], raw_data[1]); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]); + hid_debug_event(hdev, buff); + break; + case REPORT_EE_WRITE: + /* 3+1..20 data bytes with write area description */ + snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n", + "REPORT_EE_WRITE", report->id, raw_size-1); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n", + raw_data[2], raw_data[1]); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]); + hid_debug_event(hdev, buff); + if (raw_data[3] == 0) { + snprintf(buff, BUFF_SZ, "\tNo data\n"); + } else if (raw_data[3] + 4 <= raw_size) { + snprintf(buff, BUFF_SZ, "\tData: "); + hid_debug_event(hdev, buff); + dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]); + } else { + snprintf(buff, BUFF_SZ, "\tData overflowed\n"); + } + hid_debug_event(hdev, buff); + break; + case REPORT_ERASE_MEMORY: + case REPORT_BL_ERASE_MEMORY: + /* 3 data bytes with pointer inside erase block */ + snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n", + "REPORT_ERASE_MEMORY", report->id, raw_size-1); + hid_debug_event(hdev, buff); + switch (data->addr_sz) { + case 2: + snprintf(buff, BUFF_SZ, "\tAddress inside 64 byte block: 0x%02x%02x\n", + raw_data[2], raw_data[1]); + break; + case 3: + snprintf(buff, BUFF_SZ, "\tAddress inside 64 byte block: 0x%02x%02x%02x\n", + raw_data[3], raw_data[2], raw_data[1]); + break; + default: + snprintf(buff, BUFF_SZ, "\tNot supported\n"); + } + hid_debug_event(hdev, buff); + break; + case REPORT_READ_MEMORY: + case REPORT_BL_READ_MEMORY: + /* 4 data bytes with read area description */ + snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n", + "REPORT_READ_MEMORY", report->id, raw_size-1); + hid_debug_event(hdev, buff); + switch (data->addr_sz) { + case 2: + snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n", + raw_data[2], raw_data[1]); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]); + break; + case 3: + snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x%02x\n", + raw_data[3], raw_data[2], raw_data[1]); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[4]); + break; + default: + snprintf(buff, BUFF_SZ, "\tNot supported\n"); + } + hid_debug_event(hdev, buff); + break; + case REPORT_WRITE_MEMORY: + case REPORT_BL_WRITE_MEMORY: + /* 4+1..32 data bytes with write adrea description */ + snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n", + "REPORT_WRITE_MEMORY", report->id, raw_size-1); + hid_debug_event(hdev, buff); + switch (data->addr_sz) { + case 2: + snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n", + raw_data[2], raw_data[1]); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]); + hid_debug_event(hdev, buff); + if (raw_data[3] == 0) { + snprintf(buff, BUFF_SZ, "\tNo data\n"); + } else if (raw_data[3] + 4 <= raw_size) { + snprintf(buff, BUFF_SZ, "\tData: "); + hid_debug_event(hdev, buff); + dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]); + } else { + snprintf(buff, BUFF_SZ, "\tData overflowed\n"); + } + break; + case 3: + snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x%02x\n", + raw_data[3], raw_data[2], raw_data[1]); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[4]); + hid_debug_event(hdev, buff); + if (raw_data[4] == 0) { + snprintf(buff, BUFF_SZ, "\tNo data\n"); + } else if (raw_data[4] + 5 <= raw_size) { + snprintf(buff, BUFF_SZ, "\tData: "); + hid_debug_event(hdev, buff); + dump_buff_as_hex(buff, BUFF_SZ, raw_data+5, raw_data[4]); + } else { + snprintf(buff, BUFF_SZ, "\tData overflowed\n"); + } + break; + default: + snprintf(buff, BUFF_SZ, "\tNot supported\n"); + } + hid_debug_event(hdev, buff); + break; + case REPORT_SPLASH_RESTART: + /* TODO */ + break; + case REPORT_EXIT_KEYBOARD: + snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n", + "REPORT_EXIT_KEYBOARD", report->id, raw_size-1); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tRestart delay: %dms (0x%02x%02x)\n", + raw_data[1] | (raw_data[2] << 8), + raw_data[2], raw_data[1]); + hid_debug_event(hdev, buff); + break; + case REPORT_VERSION: + snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n", + "REPORT_VERSION", report->id, raw_size-1); + hid_debug_event(hdev, buff); + break; + case REPORT_DEVID: + snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n", + "REPORT_DEVID", report->id, raw_size-1); + hid_debug_event(hdev, buff); + break; + case REPORT_SPLASH_SIZE: + snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n", + "REPORT_SPLASH_SIZE", report->id, raw_size-1); + hid_debug_event(hdev, buff); + break; + case REPORT_HOOK_VERSION: + snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n", + "REPORT_HOOK_VERSION", report->id, raw_size-1); + hid_debug_event(hdev, buff); + break; + case REPORT_EXIT_FLASHER: + snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n", + "REPORT_VERSION", report->id, raw_size-1); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tRestart delay: %dms (0x%02x%02x)\n", + raw_data[1] | (raw_data[2] << 8), + raw_data[2], raw_data[1]); + hid_debug_event(hdev, buff); + break; + default: + snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n", + "<unknown>", report->id, raw_size-1); + hid_debug_event(hdev, buff); + break; + } + wake_up_interruptible(&hdev->debug_wait); + kfree(buff); +} + +static void picolcd_debug_raw_event(struct picolcd_data *data, + struct hid_device *hdev, struct hid_report *report, + u8 *raw_data, int size) +{ + char *buff; + +#define BUFF_SZ 256 + /* Avoid unnecessary overhead if debugfs is disabled */ + if (!hdev->debug_events) + return; + + buff = kmalloc(BUFF_SZ, GFP_ATOMIC); + if (!buff) + return; + + switch (report->id) { + case REPORT_ERROR_CODE: + /* 2 data bytes with affected report and error code */ + snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n", + "REPORT_ERROR_CODE", report->id, size-1); + hid_debug_event(hdev, buff); + if (raw_data[2] < ARRAY_SIZE(error_codes)) + snprintf(buff, BUFF_SZ, "\tError code 0x%02x (%s) in reply to report 0x%02x\n", + raw_data[2], error_codes[raw_data[2]], raw_data[1]); + else + snprintf(buff, BUFF_SZ, "\tError code 0x%02x in reply to report 0x%02x\n", + raw_data[2], raw_data[1]); + hid_debug_event(hdev, buff); + break; + case REPORT_KEY_STATE: + /* 2 data bytes with key state */ + snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n", + "REPORT_KEY_STATE", report->id, size-1); + hid_debug_event(hdev, buff); + if (raw_data[1] == 0) + snprintf(buff, BUFF_SZ, "\tNo key pressed\n"); + else if (raw_data[2] == 0) + snprintf(buff, BUFF_SZ, "\tOne key pressed: 0x%02x (%d)\n", + raw_data[1], raw_data[1]); + else + snprintf(buff, BUFF_SZ, "\tTwo keys pressed: 0x%02x (%d), 0x%02x (%d)\n", + raw_data[1], raw_data[1], raw_data[2], raw_data[2]); + hid_debug_event(hdev, buff); + break; + case REPORT_IR_DATA: + /* Up to 20 byes of IR scancode data */ + snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n", + "REPORT_IR_DATA", report->id, size-1); + hid_debug_event(hdev, buff); + if (raw_data[1] == 0) { + snprintf(buff, BUFF_SZ, "\tUnexpectedly 0 data length\n"); + hid_debug_event(hdev, buff); + } else if (raw_data[1] + 1 <= size) { + snprintf(buff, BUFF_SZ, "\tData length: %d\n\tIR Data: ", + raw_data[1]-1); + hid_debug_event(hdev, buff); + dump_buff_as_hex(buff, BUFF_SZ, raw_data+2, raw_data[1]-1); + hid_debug_event(hdev, buff); + } else { + snprintf(buff, BUFF_SZ, "\tOverflowing data length: %d\n", + raw_data[1]-1); + hid_debug_event(hdev, buff); + } + break; + case REPORT_EE_DATA: + /* Data buffer in response to REPORT_EE_READ or REPORT_EE_WRITE */ + snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n", + "REPORT_EE_DATA", report->id, size-1); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n", + raw_data[2], raw_data[1]); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]); + hid_debug_event(hdev, buff); + if (raw_data[3] == 0) { + snprintf(buff, BUFF_SZ, "\tNo data\n"); + hid_debug_event(hdev, buff); + } else if (raw_data[3] + 4 <= size) { + snprintf(buff, BUFF_SZ, "\tData: "); + hid_debug_event(hdev, buff); + dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]); + hid_debug_event(hdev, buff); + } else { + snprintf(buff, BUFF_SZ, "\tData overflowed\n"); + hid_debug_event(hdev, buff); + } + break; + case REPORT_MEMORY: + /* Data buffer in response to REPORT_READ_MEMORY or REPORT_WRTIE_MEMORY */ + snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n", + "REPORT_MEMORY", report->id, size-1); + hid_debug_event(hdev, buff); + switch (data->addr_sz) { + case 2: + snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n", + raw_data[2], raw_data[1]); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]); + hid_debug_event(hdev, buff); + if (raw_data[3] == 0) { + snprintf(buff, BUFF_SZ, "\tNo data\n"); + } else if (raw_data[3] + 4 <= size) { + snprintf(buff, BUFF_SZ, "\tData: "); + hid_debug_event(hdev, buff); + dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]); + } else { + snprintf(buff, BUFF_SZ, "\tData overflowed\n"); + } + break; + case 3: + snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x%02x\n", + raw_data[3], raw_data[2], raw_data[1]); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[4]); + hid_debug_event(hdev, buff); + if (raw_data[4] == 0) { + snprintf(buff, BUFF_SZ, "\tNo data\n"); + } else if (raw_data[4] + 5 <= size) { + snprintf(buff, BUFF_SZ, "\tData: "); + hid_debug_event(hdev, buff); + dump_buff_as_hex(buff, BUFF_SZ, raw_data+5, raw_data[4]); + } else { + snprintf(buff, BUFF_SZ, "\tData overflowed\n"); + } + break; + default: + snprintf(buff, BUFF_SZ, "\tNot supported\n"); + } + hid_debug_event(hdev, buff); + break; + case REPORT_VERSION: + snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n", + "REPORT_VERSION", report->id, size-1); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tFirmware version: %d.%d\n", + raw_data[2], raw_data[1]); + hid_debug_event(hdev, buff); + break; + case REPORT_BL_ERASE_MEMORY: + snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n", + "REPORT_BL_ERASE_MEMORY", report->id, size-1); + hid_debug_event(hdev, buff); + /* TODO */ + break; + case REPORT_BL_READ_MEMORY: + snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n", + "REPORT_BL_READ_MEMORY", report->id, size-1); + hid_debug_event(hdev, buff); + /* TODO */ + break; + case REPORT_BL_WRITE_MEMORY: + snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n", + "REPORT_BL_WRITE_MEMORY", report->id, size-1); + hid_debug_event(hdev, buff); + /* TODO */ + break; + case REPORT_DEVID: + snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n", + "REPORT_DEVID", report->id, size-1); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tSerial: 0x%02x%02x%02x%02x\n", + raw_data[1], raw_data[2], raw_data[3], raw_data[4]); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tType: 0x%02x\n", + raw_data[5]); + hid_debug_event(hdev, buff); + break; + case REPORT_SPLASH_SIZE: + snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n", + "REPORT_SPLASH_SIZE", report->id, size-1); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tTotal splash space: %d\n", + (raw_data[2] << 8) | raw_data[1]); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tUsed splash space: %d\n", + (raw_data[4] << 8) | raw_data[3]); + hid_debug_event(hdev, buff); + break; + case REPORT_HOOK_VERSION: + snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n", + "REPORT_HOOK_VERSION", report->id, size-1); + hid_debug_event(hdev, buff); + snprintf(buff, BUFF_SZ, "\tFirmware version: %d.%d\n", + raw_data[1], raw_data[2]); + hid_debug_event(hdev, buff); + break; + default: + snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n", + "<unknown>", report->id, size-1); + hid_debug_event(hdev, buff); + break; + } + wake_up_interruptible(&hdev->debug_wait); + kfree(buff); +} +#else +#define picolcd_debug_raw_event(data, hdev, report, raw_data, size) +#endif + +/* + * Handle raw report as sent by device + */ +static int picolcd_raw_event(struct hid_device *hdev, + struct hid_report *report, u8 *raw_data, int size) +{ + struct picolcd_data *data = hid_get_drvdata(hdev); + unsigned long flags; + int ret = 0; + + if (!data) + return 1; + + if (report->id == REPORT_KEY_STATE) { + if (data->input_keys) + ret = picolcd_raw_keypad(data, report, raw_data+1, size-1); + } else if (report->id == REPORT_IR_DATA) { + if (data->input_cir) + ret = picolcd_raw_cir(data, report, raw_data+1, size-1); + } else { + spin_lock_irqsave(&data->lock, flags); + /* + * We let the caller of picolcd_send_and_wait() check if the + * report we got is one of the expected ones or not. + */ + if (data->pending) { + memcpy(data->pending->raw_data, raw_data+1, size-1); + data->pending->raw_size = size-1; + data->pending->in_report = report; + complete(&data->pending->ready); + } + spin_unlock_irqrestore(&data->lock, flags); + } + + picolcd_debug_raw_event(data, hdev, report, raw_data, size); + return 1; +} + +/* initialize keypad input device */ +static int picolcd_init_keys(struct picolcd_data *data, + struct hid_report *report) +{ + struct hid_device *hdev = data->hdev; + struct input_dev *idev; + int error, i; + + if (!report) + return -ENODEV; + if (report->maxfield != 1 || report->field[0]->report_count != 2 || + report->field[0]->report_size != 8) { + dev_err(&hdev->dev, "unsupported KEY_STATE report"); + return -EINVAL; + } + + idev = input_allocate_device(); + if (idev == NULL) { + dev_err(&hdev->dev, "failed to allocate input device"); + return -ENOMEM; + } + input_set_drvdata(idev, hdev); + memcpy(data->keycode, def_keymap, sizeof(def_keymap)); + idev->name = hdev->name; + idev->phys = hdev->phys; + idev->uniq = hdev->uniq; + idev->id.bustype = hdev->bus; + idev->id.vendor = hdev->vendor; + idev->id.product = hdev->product; + idev->id.version = hdev->version; + idev->dev.parent = hdev->dev.parent; + idev->keycode = &data->keycode; + idev->keycodemax = PICOLCD_KEYS; + idev->keycodesize = sizeof(data->keycode[0]); + input_set_capability(idev, EV_MSC, MSC_SCAN); + set_bit(EV_REP, idev->evbit); + for (i = 0; i < PICOLCD_KEYS; i++) + input_set_capability(idev, EV_KEY, data->keycode[i]); + error = input_register_device(idev); + if (error) { + dev_err(&hdev->dev, "error registering the input device"); + input_free_device(idev); + return error; + } + data->input_keys = idev; + return 0; +} + +static void picolcd_exit_keys(struct picolcd_data *data) +{ + struct input_dev *idev = data->input_keys; + + data->input_keys = NULL; + if (idev) + input_unregister_device(idev); +} + +/* initialize CIR input device */ +static inline int picolcd_init_cir(struct picolcd_data *data, struct hid_report *report) +{ + /* support not implemented yet */ + return 0; +} + +static inline void picolcd_exit_cir(struct picolcd_data *data) +{ +} + +static int picolcd_probe_lcd(struct hid_device *hdev, struct picolcd_data *data) +{ + struct hid_report *report; + int error; + + error = picolcd_check_version(hdev); + if (error) + return error; + + if (data->version[0] != 0 && data->version[1] != 3) + dev_info(&hdev->dev, "Device with untested firmware revision, " + "please submit /sys/kernel/debug/hid/%s/rdesc for this device.\n", + dev_name(&hdev->dev)); + + /* Setup keypad input device */ + error = picolcd_init_keys(data, picolcd_in_report(REPORT_KEY_STATE, hdev)); + if (error) + goto err; + + /* Setup CIR input device */ + error = picolcd_init_cir(data, picolcd_in_report(REPORT_IR_DATA, hdev)); + if (error) + goto err; + +#ifdef CONFIG_DEBUG_FS + report = picolcd_out_report(REPORT_READ_MEMORY, hdev); + if (report && report->maxfield == 1 && report->field[0]->report_size == 8) + data->addr_sz = report->field[0]->report_count - 1; + else + data->addr_sz = -1; +#endif + return 0; +err: + picolcd_exit_cir(data); + picolcd_exit_keys(data); + return error; +} + +static int picolcd_probe_bootloader(struct hid_device *hdev, struct picolcd_data *data) +{ + struct hid_report *report; + int error; + + error = picolcd_check_version(hdev); + if (error) + return error; + + if (data->version[0] != 1 && data->version[1] != 0) + dev_info(&hdev->dev, "Device with untested bootloader revision, " + "please submit /sys/kernel/debug/hid/%s/rdesc for this device.\n", + dev_name(&hdev->dev)); + +#ifdef CONFIG_DEBUG_FS + report = picolcd_out_report(REPORT_BL_READ_MEMORY, hdev); + if (report && report->maxfield == 1 && report->field[0]->report_size == 8) + data->addr_sz = report->field[0]->report_count - 1; + else + data->addr_sz = -1; +#endif + return 0; +} + +static int picolcd_probe(struct hid_device *hdev, + const struct hid_device_id *id) +{ + struct picolcd_data *data; + int error = -ENOMEM; + + dbg_hid(PICOLCD_NAME " hardware probe...\n"); + + /* + * Let's allocate the picolcd data structure, set some reasonable + * defaults, and associate it with the device + */ + data = kzalloc(sizeof(struct picolcd_data), GFP_KERNEL); + if (data == NULL) { + dev_err(&hdev->dev, "can't allocate space for Minibox PicoLCD device data\n"); + error = -ENOMEM; + goto err_no_cleanup; + } + + spin_lock_init(&data->lock); + mutex_init(&data->mutex); + data->hdev = hdev; + if (hdev->product == USB_DEVICE_ID_PICOLCD_BOOTLOADER) + data->status |= PICOLCD_BOOTLOADER; + hid_set_drvdata(hdev, data); + + /* Parse the device reports and start it up */ + error = hid_parse(hdev); + if (error) { + dev_err(&hdev->dev, "device report parse failed\n"); + goto err_cleanup_data; + } + + /* We don't use hidinput but hid_hw_start() fails if nothing is + * claimed. So spoof claimed input. */ + hdev->claimed = HID_CLAIMED_INPUT; + error = hid_hw_start(hdev, 0); + hdev->claimed = 0; + if (error) { + dev_err(&hdev->dev, "hardware start failed\n"); + goto err_cleanup_data; + } + + error = hdev->ll_driver->open(hdev); + if (error) { + dev_err(&hdev->dev, "failed to open input interrupt pipe for key and IR events\n"); + goto err_cleanup_hid_hw; + } + + error = device_create_file(&hdev->dev, &dev_attr_operation_mode); + if (error) { + dev_err(&hdev->dev, "failed to create sysfs attributes\n"); + goto err_cleanup_hid_ll; + } + + if (data->status & PICOLCD_BOOTLOADER) + error = picolcd_probe_bootloader(hdev, data); + else + error = picolcd_probe_lcd(hdev, data); + if (error) + goto err_cleanup_sysfs; + + dbg_hid(PICOLCD_NAME " activated and initialized\n"); + return 0; + +err_cleanup_sysfs: + device_remove_file(&hdev->dev, &dev_attr_operation_mode); +err_cleanup_hid_ll: + hdev->ll_driver->close(hdev); +err_cleanup_hid_hw: + hid_hw_stop(hdev); +err_cleanup_data: + kfree(data); +err_no_cleanup: + hid_set_drvdata(hdev, NULL); + + return error; +} + +static void picolcd_remove(struct hid_device *hdev) +{ + struct picolcd_data *data = hid_get_drvdata(hdev); + unsigned long flags; + + dbg_hid(PICOLCD_NAME " hardware remove...\n"); + spin_lock_irqsave(&data->lock, flags); + data->status |= PICOLCD_FAILED; + spin_unlock_irqrestore(&data->lock, flags); + + device_remove_file(&hdev->dev, &dev_attr_operation_mode); + hdev->ll_driver->close(hdev); + hid_hw_stop(hdev); + hid_set_drvdata(hdev, NULL); + + /* Shortcut potential pending reply that will never arrive */ + spin_lock_irqsave(&data->lock, flags); + if (data->pending) + complete(&data->pending->ready); + spin_unlock_irqrestore(&data->lock, flags); + + /* Cleanup input */ + picolcd_exit_cir(data); + picolcd_exit_keys(data); + + mutex_destroy(&data->mutex); + /* Finally, clean up the picolcd data itself */ + kfree(data); +} + +static const struct hid_device_id picolcd_devices[] = { + { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD) }, + { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD_BOOTLOADER) }, + { } +}; +MODULE_DEVICE_TABLE(hid, picolcd_devices); + +static struct hid_driver picolcd_driver = { + .name = "hid-picolcd", + .id_table = picolcd_devices, + .probe = picolcd_probe, + .remove = picolcd_remove, + .raw_event = picolcd_raw_event, +}; + +static int __init picolcd_init(void) +{ + return hid_register_driver(&picolcd_driver); +} + +static void __exit picolcd_exit(void) +{ + hid_unregister_driver(&picolcd_driver); +} + +module_init(picolcd_init); +module_exit(picolcd_exit); +MODULE_DESCRIPTION("Minibox graphics PicoLCD Driver"); +MODULE_LICENSE("GPL v2"); |
