| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
This rmoves the codes for emulated PCI config space as it can be
supported by generic PCI virtual device:
* The PCI virtual device and NPU device are created at same time.
* Uses PCI virtual device and filter to access NPU (PCI) device's
config space.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
|
| |
|
|
|
|
|
| |
We also remove the NPUERR macros so that the FWTS parsing magic
can construct find the prlog statements.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
All kinds of PHBs are maintaining a spinlock. At mean while, the
spinlock is acquired or released by backends for phb_ops->lock()
or phb_ops->unlock(). There're no difference of the logic on all
kinds of PHBs. So it's reasonable to maintain the lock in the
generic layer (struct phb).
This moves lock from specific PHB to generic one. The spinlock is
initialized when the generic PHB is registered in pci_register_phb().
Also, two inline functions phb_{lock, unlock}() are introduced to
acquire/release it. No logical changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Once the NPU has been reset, it should no longer have any fixable errors.
Clear any relevant error registers at the end of the reset procedure.
There may be other error registers that should be cleared, if found they
will be added later.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Acked-By: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
EEH in the kernel shuts down MMIO BARs as part of freeze recovery.
This can cause the reset procedure, which you probably want to work
during a freeze, to fail because it can't do operations with MMIO.
Refactor the MMIO operations to use SCOM instead.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Acked-By: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
|
|
|
This patch adds support for the NPU Nvlink PHB type. It provides
access to each nvlink in the system by exposing them as PCIe devices
under a NPU PHB type. Each PCIe device has a configuration space
implemented in software which indicates the base address of the
DL/TL/PL registers required by the device drivers.
It also presents one LSI per device which is used to signal device
drivers of changes in device status. The configuration space also adds
a vendor specific capability which is used primarily by device drivers
to power on an train the IBM PHY.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
|
