Commit message (Expand) | Author | Age | Files | Lines | |
---|---|---|---|---|---|
* | kernel: Move to 4.13 kernel (backport) | Joel Stanley | 2018-05-16 | 9 | -9/+9 |
* | Revert "Delay OCC binding from host boot complete signal" | Raptor Engineering Development Team | 2018-05-15 | 1 | -4/+0 |
* | Raise kernel tick rate and forcibly enable hrtimersraptor-v1.0505-11-2018 | Raptor Engineering Development Team | 2018-05-14 | 1 | -0/+10 |
* | Delay OCC binding from host boot complete signal | Raptor Engineering Development Team | 2018-05-14 | 1 | -0/+4 |
* | Lower chassis ambient set point due to addition of averaged intake sensors | Raptor Engineering Development Team | 2018-05-13 | 1 | -1/+1 |
* | Add CPU1 ambient sensor and PCIe ambient sensor to fan control ambient temper... | Raptor Engineering Development Team | 2018-05-13 | 1 | -0/+2 |
* | Add CPU1 ambient sensor to IPMI SDR on Talos II | Raptor Engineering Development Team | 2018-05-13 | 2 | -0/+23 |
* | Remove unneccessary fan speed maps for chassis fans | Raptor Engineering Development Team | 2018-05-13 | 1 | -16/+2 |
* | Fix ambient temperature sensor mappings on Talos II | Raptor Engineering Development Team | 2018-05-13 | 1 | -2/+3 |
* | Attempt to detect host power down if watchdog fails | Raptor Engineering Development Team | 2018-05-13 | 1 | -0/+18 |
* | Tweak chassis fan PID controls again to mitigate integrator wind-up | Raptor Engineering Development Team | 2018-05-12 | 1 | -2/+2 |
* | Do not attempt to bind OCC drivers until IPL is complete | Raptor Engineering Development Team | 2018-05-12 | 1 | -0/+8 |
* | Load final manufacturer ID and device ID data into IPMI data fields | Raptor Engineering Development Team | 2018-05-11 | 1 | -1/+1 |
* | Add support for secondary PCIe region ambient temperature sensor on Talos II ... | Raptor Engineering Development Team | 2018-05-09 | 3 | -0/+26 |
* | Add initial IPMI sensor mappings for Talos II | Raptor Engineering Development Team | 2018-05-09 | 6 | -0/+1865 |
* | FRU: Add Entity ID in the host FRU inventory yaml | Ratan Gupta | 2018-05-08 | 1 | -0/+6 |
* | Add missing mutability attributes to IPMI inventory YAML | Raptor Engineering Development Team | 2018-05-08 | 1 | -0/+71 |
* | Update IPMI YAML from Romulus source | Raptor Engineering Development Team | 2018-05-08 | 1 | -437/+499 |
* | sensor: Modify config for sensor to add additional fields | Tom Joseph | 2018-05-08 | 2 | -0/+7 |
* | Bring boot VDN in line with values in datasheet | Raptor Engineering Development Team | 2018-05-08 | 1 | -1/+1 |
* | Fix power sequencing on Talos II. | Brandon Bergren | 2018-05-08 | 2 | -0/+4 |
* | Tweak chassis fan PID tuning | Raptor Engineering Development Team | 2018-05-07 | 1 | -2/+2 |
* | Remove broken ASpeed PWM fan and tach driver tie-in | Raptor Engineering Development Team | 2018-05-07 | 2 | -2/+0 |
* | Back off chassis fan proportional constantraptor-v1.0405-04-2018 | Raptor Engineering Development Team | 2018-05-04 | 1 | -1/+1 |
* | Lower chassis fan floor maps slightly to reduce unneccessary fan noise under ... | Raptor Engineering Development Team | 2018-05-04 | 1 | -7/+7 |
* | Switch to PID control of main fans | Raptor Engineering Development Team | 2018-04-29 | 1 | -62/+65 |
* | Wait 5 seconds for fans to reach full speed after fan controller init | Raptor Engineering Development Team | 2018-04-28 | 1 | -1/+1 |
* | Update fan monitor YAML to new syntax | Raptor Engineering Development Team | 2018-04-28 | 1 | -1/+7 |
* | Update fan event YAML to new syntax | Raptor Engineering Development Team | 2018-04-28 | 1 | -193/+225 |
* | Make decrease symmetric with increase | Raptor Engineering Development Team | 2018-04-28 | 2 | -12/+12 |
* | Don't set zone 2 to high speed when fewer than 4 chassis fans are installed, ... | Raptor Engineering Development Team | 2018-04-28 | 1 | -76/+0 |
* | Tighten up fan response again | Raptor Engineering Development Team | 2018-04-28 | 2 | -15/+15 |
* | Switch openpower-dbus-interfaces to Raptor Computing Systems GIT repository | Raptor Engineering Development Team | 2018-04-28 | 1 | -1/+1 |
* | Raise CPU core temp setpoints | Raptor Engineering Development Team | 2018-04-20 | 2 | -71/+71 |
* | Enhance OCC communication failure error recovery | Raptor Engineering Development Team | 2018-04-14 | 1 | -0/+13 |
* | Revup pdbg | Raptor Engineering Development Team | 2018-04-14 | 1 | -1/+1 |
* | Allow the on-board VGA device to be enabled or disabled based on FPGA jumper ... | Raptor Engineering Development Team | 2018-04-14 | 4 | -1/+60 |
* | Minimize chassis fan hunting with additional fan speed floor mappings in comm... | Raptor Engineering Development Team | 2018-02-19 | 1 | -7/+13 |
* | Adjust floor threshold map to avoid chassis fan hunting at typical ambient te... | Raptor Engineering Development Team | 2018-02-19 | 1 | -7/+7 |
* | Loosen ambient temperature fan controls somewhat | Raptor Engineering Development Team | 2018-02-19 | 1 | -3/+3 |
* | Set chassis fan speeds based on on-board ambient temperature sensor | Raptor Engineering Development Team | 2018-02-19 | 1 | -60/+11 |
* | Use hardbeep instead of softbeep on Talos systems | Raptor Engineering Development Team | 2018-01-25 | 1 | -1/+1 |
* | Split fan control zones for CPU0 and CPU1 | Raptor Engineering Development Team | 2018-01-23 | 3 | -22/+93 |
* | Add softbeep packaging files | Raptor Engineering Development Team | 2018-01-22 | 1 | -1/+1 |
* | Reset OCC on error detection | Raptor Engineering Development Team | 2018-01-22 | 1 | -2/+11 |
* | Remove DD1 VCS workaround hack | Raptor Engineering Development Team | 2018-01-22 | 9 | -97/+2 |
* | Recover from loss of either OCC | Raptor Engineering Development Team | 2018-01-22 | 1 | -3/+39 |
* | Restart OCC service before restarting fan controller | Raptor Engineering Development Team | 2018-01-21 | 1 | -2/+17 |
* | Fix incorrect Talos fan control settings | Raptor Engineering Development Team | 2018-01-21 | 3 | -21/+21 |
* | Enable ambient temperature sensor | Raptor Engineering Development Team | 2018-01-21 | 2 | -0/+2 |