1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
|
/*
* Bock-W board support
*
* Copyright (C) 2013 Renesas Solutions Corp.
* Copyright (C) 2013 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; version 2 of the License.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#include <linux/mfd/tmio.h>
#include <linux/mmc/host.h>
#include <linux/mtd/partitions.h>
#include <linux/pinctrl/machine.h>
#include <linux/platform_device.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/smsc911x.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <mach/common.h>
#include <mach/irqs.h>
#include <mach/r8a7778.h>
#include <asm/mach/arch.h>
/*
* CN9(Upper side) SCIF/RCAN selection
*
* 1,4 3,6
* SW40 SCIF RCAN
* SW41 SCIF RCAN
*/
/*
* MMC (CN26) pin
*
* SW6 (D2) 3 pin
* SW7 (D5) ON
* SW8 (D3) 3 pin
* SW10 (D4) 1 pin
* SW12 (CLK) 1 pin
* SW13 (D6) 3 pin
* SW14 (CMD) ON
* SW15 (D6) 1 pin
* SW16 (D0) ON
* SW17 (D1) ON
* SW18 (D7) 3 pin
* SW19 (MMC) 1 pin
*/
/* Dummy supplies, where voltage doesn't matter */
static struct regulator_consumer_supply dummy_supplies[] = {
REGULATOR_SUPPLY("vddvario", "smsc911x"),
REGULATOR_SUPPLY("vdd33a", "smsc911x"),
};
static struct smsc911x_platform_config smsc911x_data = {
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
.irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
.flags = SMSC911X_USE_32BIT,
.phy_interface = PHY_INTERFACE_MODE_MII,
};
static struct resource smsc911x_resources[] = {
DEFINE_RES_MEM(0x18300000, 0x1000),
DEFINE_RES_IRQ(irq_pin(0)), /* IRQ 0 */
};
/* USB */
static struct rcar_phy_platform_data usb_phy_platform_data __initdata;
/* SDHI */
static struct sh_mobile_sdhi_info sdhi0_info = {
.tmio_caps = MMC_CAP_SD_HIGHSPEED,
.tmio_ocr_mask = MMC_VDD_165_195 | MMC_VDD_32_33 | MMC_VDD_33_34,
.tmio_flags = TMIO_MMC_HAS_IDLE_WAIT,
};
static struct sh_eth_plat_data ether_platform_data __initdata = {
.phy = 0x01,
.edmac_endian = EDMAC_LITTLE_ENDIAN,
.register_type = SH_ETH_REG_FAST_RCAR,
.phy_interface = PHY_INTERFACE_MODE_RMII,
/*
* Although the LINK signal is available on the board, it's connected to
* the link/activity LED output of the PHY, thus the link disappears and
* reappears after each packet. We'd be better off ignoring such signal
* and getting the link state from the PHY indirectly.
*/
.no_ether_link = 1,
};
/* I2C */
static struct i2c_board_info i2c0_devices[] = {
{
I2C_BOARD_INFO("rx8581", 0x51),
},
};
/* HSPI*/
static struct mtd_partition m25p80_spi_flash_partitions[] = {
{
.name = "data(spi)",
.size = 0x0100000,
.offset = 0,
},
};
static struct flash_platform_data spi_flash_data = {
.name = "m25p80",
.type = "s25fl008k",
.parts = m25p80_spi_flash_partitions,
.nr_parts = ARRAY_SIZE(m25p80_spi_flash_partitions),
};
static struct spi_board_info spi_board_info[] __initdata = {
{
.modalias = "m25p80",
.max_speed_hz = 104000000,
.chip_select = 0,
.bus_num = 0,
.mode = SPI_MODE_0,
.platform_data = &spi_flash_data,
},
};
/* MMC */
static struct sh_mmcif_plat_data sh_mmcif_plat = {
.sup_pclk = 0,
.ocr = MMC_VDD_165_195 | MMC_VDD_32_33 | MMC_VDD_33_34,
.caps = MMC_CAP_4_BIT_DATA |
MMC_CAP_8_BIT_DATA |
MMC_CAP_NEEDS_POLL,
};
static const struct pinctrl_map bockw_pinctrl_map[] = {
/* Ether */
PIN_MAP_MUX_GROUP_DEFAULT("r8a777x-ether", "pfc-r8a7778",
"ether_rmii", "ether"),
/* HSPI0 */
PIN_MAP_MUX_GROUP_DEFAULT("sh-hspi.0", "pfc-r8a7778",
"hspi0_a", "hspi0"),
/* MMC */
PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif", "pfc-r8a7778",
"mmc_data8", "mmc"),
PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif", "pfc-r8a7778",
"mmc_ctrl", "mmc"),
/* SCIF0 */
PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.0", "pfc-r8a7778",
"scif0_data_a", "scif0"),
PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.0", "pfc-r8a7778",
"scif0_ctrl", "scif0"),
/* USB */
PIN_MAP_MUX_GROUP_DEFAULT("ehci-platform", "pfc-r8a7778",
"usb0", "usb0"),
PIN_MAP_MUX_GROUP_DEFAULT("ehci-platform", "pfc-r8a7778",
"usb1", "usb1"),
/* SDHI0 */
PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7778",
"sdhi0", "sdhi0"),
};
#define FPGA 0x18200000
#define IRQ0MR 0x30
#define PFC 0xfffc0000
#define PUPR4 0x110
static void __init bockw_init(void)
{
void __iomem *base;
r8a7778_clock_init();
r8a7778_init_irq_extpin(1);
r8a7778_add_standard_devices();
r8a7778_add_usb_phy_device(&usb_phy_platform_data);
r8a7778_add_ether_device(ðer_platform_data);
r8a7778_add_i2c_device(0);
r8a7778_add_hspi_device(0);
r8a7778_add_mmc_device(&sh_mmcif_plat);
i2c_register_board_info(0, i2c0_devices,
ARRAY_SIZE(i2c0_devices));
spi_register_board_info(spi_board_info,
ARRAY_SIZE(spi_board_info));
pinctrl_register_mappings(bockw_pinctrl_map,
ARRAY_SIZE(bockw_pinctrl_map));
r8a7778_pinmux_init();
/* for SMSC */
base = ioremap_nocache(FPGA, SZ_1M);
if (base) {
/*
* CAUTION
*
* IRQ0/1 is cascaded interrupt from FPGA.
* it should be cared in the future
* Now, it is assuming IRQ0 was used only from SMSC.
*/
u16 val = ioread16(base + IRQ0MR);
val &= ~(1 << 4); /* enable SMSC911x */
iowrite16(val, base + IRQ0MR);
iounmap(base);
regulator_register_fixed(0, dummy_supplies,
ARRAY_SIZE(dummy_supplies));
platform_device_register_resndata(
&platform_bus, "smsc911x", -1,
smsc911x_resources, ARRAY_SIZE(smsc911x_resources),
&smsc911x_data, sizeof(smsc911x_data));
}
/* for SDHI */
base = ioremap_nocache(PFC, 0x200);
if (base) {
/*
* FIXME
*
* SDHI CD/WP pin needs pull-up
*/
iowrite32(ioread32(base + PUPR4) | (3 << 26), base + PUPR4);
iounmap(base);
r8a7778_sdhi_init(0, &sdhi0_info);
}
}
static const char *bockw_boards_compat_dt[] __initdata = {
"renesas,bockw",
NULL,
};
DT_MACHINE_START(BOCKW_DT, "bockw")
.init_early = r8a7778_init_delay,
.init_irq = r8a7778_init_irq_dt,
.init_machine = bockw_init,
.init_time = shmobile_timer_init,
.dt_compat = bockw_boards_compat_dt,
.init_late = r8a7778_init_late,
MACHINE_END
|
