1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
|
synopsys DWC3 CORE
DWC3- USB3 CONTROLLER. Complies to the generic USB binding properties
as described in 'usb/generic.txt'
Required properties:
- compatible: must be "snps,dwc3"
- reg : Address and length of the register set for the device
- interrupts: Interrupts used by the dwc3 controller.
Optional properties:
- usb-phy : array of phandle for the PHY device. The first element
in the array is expected to be a handle to the USB2/HS PHY and
the second element is expected to be a handle to the USB3/SS PHY
- phys: from the *Generic PHY* bindings
- phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy"
or "usb3-phy".
- snps,usb3_lpm_capable: determines if platform is USB3 LPM capable
- snps,disable_scramble_quirk: true when SW should disable data scrambling.
Only really useful for FPGA builds.
- snps,has-lpm-erratum: true when DWC3 was configured with LPM Erratum enabled
- snps,lpm-nyet-threshold: LPM NYET threshold
- snps,u2exit_lfps_quirk: set if we want to enable u2exit lfps quirk
- snps,u2ss_inp3_quirk: set if we enable P3 OK for U2/SS Inactive quirk
- snps,req_p1p2p3_quirk: when set, the core will always request for
P1/P2/P3 transition sequence.
- snps,del_p1p2p3_quirk: when set core will delay P1/P2/P3 until a certain
amount of 8B10B errors occur.
- snps,del_phy_power_chg_quirk: when set core will delay PHY power change
from P0 to P1/P2/P3.
- snps,lfps_filter_quirk: when set core will filter LFPS reception.
- snps,rx_detect_poll_quirk: when set core will disable a 400us delay to start
Polling LFPS after RX.Detect.
- snps,tx_de_emphasis_quirk: when set core will set Tx de-emphasis value.
- snps,tx_de_emphasis: the value driven to the PHY is controlled by the
LTSSM during USB3 Compliance mode.
- snps,dis_u3_susphy_quirk: when set core will disable USB3 suspend phy.
- snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy.
- snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG,
disabling the suspend signal to the PHY.
- snps,dis_rxdet_inp3_quirk: when set core will disable receiver detection
in PHY P3 power state.
- snps,dis-u2-freeclk-exists-quirk: when set, clear the u2_freeclk_exists
in GUSB2PHYCFG, specify that USB2 PHY doesn't provide
a free-running PHY clock.
- snps,dis-del-phy-power-chg-quirk: when set core will change PHY power
from P0 to P1/P2/P3 without delay.
- snps,is-utmi-l1-suspend: true when DWC3 asserts output signal
utmi_l1_suspend_n, false when asserts utmi_sleep_n
- snps,hird-threshold: HIRD threshold
- snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for
UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3.
- snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ
register for post-silicon frame length adjustment when the
fladj_30mhz_sdbnd signal is invalid or incorrect.
- <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated.
- in addition all properties from usb-xhci.txt from the current directory are
supported as well
This is usually a subnode to DWC3 glue to which it is connected.
dwc3@4a030000 {
compatible = "snps,dwc3";
reg = <0x4a030000 0xcfff>;
interrupts = <0 92 4>
usb-phy = <&usb2_phy>, <&usb3,phy>;
};
|
