summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt
blob: 9e9e9ef9f852f847305e7257645057a914ea434d (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
Broadcom Capri Pin Controller

This is a pin controller for the Broadcom BCM281xx SoC family, which includes
BCM11130, BCM11140, BCM11351, BCM28145, and BCM28155 SoCs.

=== Pin Controller Node ===

Required Properties:

- compatible:	Must be "brcm,capri-pinctrl".
- reg:		Base address of the PAD Controller register block and the size
		of the block.

For example, the following is the bare minimum node:

	pinctrl@35004800 {
		compatible = "brcm,capri-pinctrl";
		reg = <0x35004800 0x430>;
	};

As a pin controller device, in addition to the required properties, this node
should also contain the pin configuration nodes that client devices reference,
if any.

=== Pin Configuration Node ===

Each pin configuration node is a sub-node of the pin controller node and is a
container of an arbitrary number of subnodes, called pin group nodes in this
document.

Please refer to the pinctrl-bindings.txt in this directory for details of the
common pinctrl bindings used by client devices, including the definition of a
"pin configuration node".

=== Pin Group Node ===

A pin group node specifies the desired pin mux and/or pin configuration for an
arbitrary number of pins.  The name of the pin group node is optional and not
used.

A pin group node only affects the properties specified in the node, and has no
effect on any properties that are omitted.

The pin group node accepts a subset of the generic pin config properties. For
details generic pin config properties, please refer to pinctrl-bindings.txt
and <include/linux/pinctrl/pinconfig-generic.h>.

Each pin controlled by this pin controller belong to one of three types:
Standard, I2C, and HDMI.  Each type accepts a different set of pin config
properties.  A list of pins and their types is provided below.

Required Properties (applicable to all pins):

- pins:		Multiple strings.  Specifies the name(s) of one or more pins to
		be configured by this node.

Optional Properties (for standard pins):

- function:			String. Specifies the pin mux selection. Values
				must be one of: "alt1", "alt2", "alt3", "alt4"
- input-schmitt-enable:		No arguments. Enable schmitt-trigger mode.
- input-schmitt-disable:	No arguments. Disable schmitt-trigger mode.
- bias-pull-up:			No arguments. Pull up on pin.
- bias-pull-down:		No arguments. Pull down on pin.
- bias-disable:			No arguments. Disable pin bias.
- slew-rate:			Integer. Meaning depends on configured pin mux:
				*_SCL or *_SDA:
					0: Standard(100kbps)& Fast(400kbps) mode
					1: Highspeed (3.4Mbps) mode
				IC_DM or IC_DP:
					0: normal slew rate
					1: fast slew rate
				Otherwise:
					0: fast slew rate
					1: normal slew rate
- input-enable:			No arguements. Enable input (does not affect
				output.)
- input-disable:		No arguements. Disable input (does not affect
				output.)
- drive-strength:		Integer. Drive strength in mA.  Valid values are
				2, 4, 6, 8, 10, 12, 14, 16 mA.

Optional Properties (for I2C pins):

- function:			String. Specifies the pin mux selection. Values
				must be one of: "alt1", "alt2", "alt3", "alt4"
- bias-pull-up:			Integer. Pull up strength in Ohm. There are 3
				pull-up resisitors (1.2k, 1.8k, 2.7k) available
				in parallel for I2C pins, so the valid values
				are: 568, 720, 831, 1080, 1200, 1800, 2700 Ohm.
- bias-disable:			No arguments. Disable pin bias.
- slew-rate:			Integer. Meaning depends on configured pin mux:
				*_SCL or *_SDA:
					0: Standard(100kbps)& Fast(400kbps) mode
					1: Highspeed (3.4Mbps) mode
				IC_DM or IC_DP:
					0: normal slew rate
					1: fast slew rate
				Otherwise:
					0: fast slew rate
					1: normal slew rate
- input-enable:			No arguements. Enable input (does not affect
				output.)
- input-disable:		No arguements. Disable input (does not affect
				output.)

Optional Properties (for HDMI pins):

- function:			String. Specifies the pin mux selection. Values
				must be one of: "alt1", "alt2", "alt3", "alt4"
- slew-rate:			Integer. Controls slew rate.
					0: Standard(100kbps)& Fast(400kbps) mode
					1: Highspeed (3.4Mbps) mode
- input-enable:			No arguements. Enable input (does not affect
				output.)
- input-disable:		No arguements. Disable input (does not affect
				output.)

Example:
// pin controller node
pinctrl@35004800 {
	compatible = "brcm,capri-pinctrl";
	reg = <0x35004800 0x430>;

	// pin configuration node
	dev_a_default: dev_a_active {
		//group node defining 1 standard pin
		grp_1 {
			pins		= "std_pin1";
			function	= "alt1";
			input-schmitt-enable;
			bias-disable;
			slew-rate	= <1>;
			drive-strength	= <4>;
		};

		// group node defining 2 I2C pins
		grp_2 {
			pins		= "i2c_pin1", "i2c_pin2";
			function	= "alt2";
			bias-pull-up	= <720>;
			input-enable;
		};

		// group node defining 2 HDMI pins
		grp_3 {
			pins		= "hdmi_pin1", "hdmi_pin2";
			function	= "alt3";
			slew-rate	= <1>;
		};

		// other pin group nodes
		...
	};

	// other pin configuration nodes
	...
};

In the example above, "dev_a_active" is a pin configuration node with a number
of sub-nodes.  In the pin group node "grp_1", one pin, "std_pin1", is defined in
the "pins" property.  Thus, the remaining properties in the "grp_1" node applies
only to this pin, including the following settings:
 - setting pinmux to "alt1"
 - enabling schmitt-trigger (hystersis) mode
 - disabling pin bias
 - setting the slew-rate to 1
 - setting the drive strength to 4 mA
Note that neither "input-enable" nor "input-disable" was specified - the pinctrl
subsystem will therefore leave this property unchanged from whatever state it
was in before applying these changes.

The "pins" property in the pin group node "grp_2" specifies two pins -
"i2c_pin1" and "i2c_pin2"; the remaining properties in this pin group node,
therefore, applies to both of these pins.  The properties include:
 - setting pinmux to "alt2"
 - setting pull-up resistance to 720 Ohm (ie. enabling 1.2k and 1.8k resistors
   in parallel)
 - enabling both pins' input
"slew-rate" is not specified in this pin group node, so the slew-rate for these
pins are left as-is.

Finally, "grp_3" defines two HDMI pins.  The following properties are applied to
both pins:
 - setting pinmux to "alt3"
 - setting slew-rate to 1; for HDMI pins, this corresponds to the 3.4 Mbps
   Highspeed mode
The input is neither enabled or disabled, and is left untouched.

=== Pin Names and Type ===

The following are valid pin names and their pin types:

	"adcsync",		Standard
	"bat_rm",		Standard
	"bsc1_scl",		I2C
	"bsc1_sda",		I2C
	"bsc2_scl",		I2C
	"bsc2_sda",		I2C
	"classgpwr",		Standard
	"clk_cx8",		Standard
	"clkout_0",		Standard
	"clkout_1",		Standard
	"clkout_2",		Standard
	"clkout_3",		Standard
	"clkreq_in_0",		Standard
	"clkreq_in_1",		Standard
	"cws_sys_req1",		Standard
	"cws_sys_req2",		Standard
	"cws_sys_req3",		Standard
	"digmic1_clk",		Standard
	"digmic1_dq",		Standard
	"digmic2_clk",		Standard
	"digmic2_dq",		Standard
	"gpen13",		Standard
	"gpen14",		Standard
	"gpen15",		Standard
	"gpio00",		Standard
	"gpio01",		Standard
	"gpio02",		Standard
	"gpio03",		Standard
	"gpio04",		Standard
	"gpio05",		Standard
	"gpio06",		Standard
	"gpio07",		Standard
	"gpio08",		Standard
	"gpio09",		Standard
	"gpio10",		Standard
	"gpio11",		Standard
	"gpio12",		Standard
	"gpio13",		Standard
	"gpio14",		Standard
	"gps_pablank",		Standard
	"gps_tmark",		Standard
	"hdmi_scl",		HDMI
	"hdmi_sda",		HDMI
	"ic_dm",		Standard
	"ic_dp",		Standard
	"kp_col_ip_0",		Standard
	"kp_col_ip_1",		Standard
	"kp_col_ip_2",		Standard
	"kp_col_ip_3",		Standard
	"kp_row_op_0",		Standard
	"kp_row_op_1",		Standard
	"kp_row_op_2",		Standard
	"kp_row_op_3",		Standard
	"lcd_b_0",		Standard
	"lcd_b_1",		Standard
	"lcd_b_2",		Standard
	"lcd_b_3",		Standard
	"lcd_b_4",		Standard
	"lcd_b_5",		Standard
	"lcd_b_6",		Standard
	"lcd_b_7",		Standard
	"lcd_g_0",		Standard
	"lcd_g_1",		Standard
	"lcd_g_2",		Standard
	"lcd_g_3",		Standard
	"lcd_g_4",		Standard
	"lcd_g_5",		Standard
	"lcd_g_6",		Standard
	"lcd_g_7",		Standard
	"lcd_hsync",		Standard
	"lcd_oe",		Standard
	"lcd_pclk",		Standard
	"lcd_r_0",		Standard
	"lcd_r_1",		Standard
	"lcd_r_2",		Standard
	"lcd_r_3",		Standard
	"lcd_r_4",		Standard
	"lcd_r_5",		Standard
	"lcd_r_6",		Standard
	"lcd_r_7",		Standard
	"lcd_vsync",		Standard
	"mdmgpio0",		Standard
	"mdmgpio1",		Standard
	"mdmgpio2",		Standard
	"mdmgpio3",		Standard
	"mdmgpio4",		Standard
	"mdmgpio5",		Standard
	"mdmgpio6",		Standard
	"mdmgpio7",		Standard
	"mdmgpio8",		Standard
	"mphi_data_0",		Standard
	"mphi_data_1",		Standard
	"mphi_data_2",		Standard
	"mphi_data_3",		Standard
	"mphi_data_4",		Standard
	"mphi_data_5",		Standard
	"mphi_data_6",		Standard
	"mphi_data_7",		Standard
	"mphi_data_8",		Standard
	"mphi_data_9",		Standard
	"mphi_data_10",		Standard
	"mphi_data_11",		Standard
	"mphi_data_12",		Standard
	"mphi_data_13",		Standard
	"mphi_data_14",		Standard
	"mphi_data_15",		Standard
	"mphi_ha0",		Standard
	"mphi_hat0",		Standard
	"mphi_hat1",		Standard
	"mphi_hce0_n",		Standard
	"mphi_hce1_n",		Standard
	"mphi_hrd_n",		Standard
	"mphi_hwr_n",		Standard
	"mphi_run0",		Standard
	"mphi_run1",		Standard
	"mtx_scan_clk",		Standard
	"mtx_scan_data",	Standard
	"nand_ad_0",		Standard
	"nand_ad_1",		Standard
	"nand_ad_2",		Standard
	"nand_ad_3",		Standard
	"nand_ad_4",		Standard
	"nand_ad_5",		Standard
	"nand_ad_6",		Standard
	"nand_ad_7",		Standard
	"nand_ale",		Standard
	"nand_cen_0",		Standard
	"nand_cen_1",		Standard
	"nand_cle",		Standard
	"nand_oen",		Standard
	"nand_rdy_0",		Standard
	"nand_rdy_1",		Standard
	"nand_wen",		Standard
	"nand_wp",		Standard
	"pc1",			Standard
	"pc2",			Standard
	"pmu_int",		Standard
	"pmu_scl",		I2C
	"pmu_sda",		I2C
	"rfst2g_mtsloten3g",	Standard
	"rgmii_0_rx_ctl",	Standard
	"rgmii_0_rxc",		Standard
	"rgmii_0_rxd_0",	Standard
	"rgmii_0_rxd_1",	Standard
	"rgmii_0_rxd_2",	Standard
	"rgmii_0_rxd_3",	Standard
	"rgmii_0_tx_ctl",	Standard
	"rgmii_0_txc",		Standard
	"rgmii_0_txd_0",	Standard
	"rgmii_0_txd_1",	Standard
	"rgmii_0_txd_2",	Standard
	"rgmii_0_txd_3",	Standard
	"rgmii_1_rx_ctl",	Standard
	"rgmii_1_rxc",		Standard
	"rgmii_1_rxd_0",	Standard
	"rgmii_1_rxd_1",	Standard
	"rgmii_1_rxd_2",	Standard
	"rgmii_1_rxd_3",	Standard
	"rgmii_1_tx_ctl",	Standard
	"rgmii_1_txc",		Standard
	"rgmii_1_txd_0",	Standard
	"rgmii_1_txd_1",	Standard
	"rgmii_1_txd_2",	Standard
	"rgmii_1_txd_3",	Standard
	"rgmii_gpio_0",		Standard
	"rgmii_gpio_1",		Standard
	"rgmii_gpio_2",		Standard
	"rgmii_gpio_3",		Standard
	"rtxdata2g_txdata3g1",	Standard
	"rtxen2g_txdata3g2",	Standard
	"rxdata3g0",		Standard
	"rxdata3g1",		Standard
	"rxdata3g2",		Standard
	"sdio1_clk",		Standard
	"sdio1_cmd",		Standard
	"sdio1_data_0",		Standard
	"sdio1_data_1",		Standard
	"sdio1_data_2",		Standard
	"sdio1_data_3",		Standard
	"sdio4_clk",		Standard
	"sdio4_cmd",		Standard
	"sdio4_data_0",		Standard
	"sdio4_data_1",		Standard
	"sdio4_data_2",		Standard
	"sdio4_data_3",		Standard
	"sim_clk",		Standard
	"sim_data",		Standard
	"sim_det",		Standard
	"sim_resetn",		Standard
	"sim2_clk",		Standard
	"sim2_data",		Standard
	"sim2_det",		Standard
	"sim2_resetn",		Standard
	"sri_c",		Standard
	"sri_d",		Standard
	"sri_e",		Standard
	"ssp_extclk",		Standard
	"ssp0_clk",		Standard
	"ssp0_fs",		Standard
	"ssp0_rxd",		Standard
	"ssp0_txd",		Standard
	"ssp2_clk",		Standard
	"ssp2_fs_0",		Standard
	"ssp2_fs_1",		Standard
	"ssp2_fs_2",		Standard
	"ssp2_fs_3",		Standard
	"ssp2_rxd_0",		Standard
	"ssp2_rxd_1",		Standard
	"ssp2_txd_0",		Standard
	"ssp2_txd_1",		Standard
	"ssp3_clk",		Standard
	"ssp3_fs",		Standard
	"ssp3_rxd",		Standard
	"ssp3_txd",		Standard
	"ssp4_clk",		Standard
	"ssp4_fs",		Standard
	"ssp4_rxd",		Standard
	"ssp4_txd",		Standard
	"ssp5_clk",		Standard
	"ssp5_fs",		Standard
	"ssp5_rxd",		Standard
	"ssp5_txd",		Standard
	"ssp6_clk",		Standard
	"ssp6_fs",		Standard
	"ssp6_rxd",		Standard
	"ssp6_txd",		Standard
	"stat_1",		Standard
	"stat_2",		Standard
	"sysclken",		Standard
	"traceclk",		Standard
	"tracedt00",		Standard
	"tracedt01",		Standard
	"tracedt02",		Standard
	"tracedt03",		Standard
	"tracedt04",		Standard
	"tracedt05",		Standard
	"tracedt06",		Standard
	"tracedt07",		Standard
	"tracedt08",		Standard
	"tracedt09",		Standard
	"tracedt10",		Standard
	"tracedt11",		Standard
	"tracedt12",		Standard
	"tracedt13",		Standard
	"tracedt14",		Standard
	"tracedt15",		Standard
	"txdata3g0",		Standard
	"txpwrind",		Standard
	"uartb1_ucts",		Standard
	"uartb1_urts",		Standard
	"uartb1_urxd",		Standard
	"uartb1_utxd",		Standard
	"uartb2_urxd",		Standard
	"uartb2_utxd",		Standard
	"uartb3_ucts",		Standard
	"uartb3_urts",		Standard
	"uartb3_urxd",		Standard
	"uartb3_utxd",		Standard
	"uartb4_ucts",		Standard
	"uartb4_urts",		Standard
	"uartb4_urxd",		Standard
	"uartb4_utxd",		Standard
	"vc_cam1_scl",		I2C
	"vc_cam1_sda",		I2C
	"vc_cam2_scl",		I2C
	"vc_cam2_sda",		I2C
	"vc_cam3_scl",		I2C
	"vc_cam3_sda",		I2C
OpenPOWER on IntegriCloud