| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
ASoC: Fixes for v5.5
This is mostly driver specific fixes, plus an error handling fix
in the core. There is a rather large diffstat for the stm32 SAI
driver, this is a very large but mostly mechanical update which
wraps every register access in the driver to allow a fix to the
locking which avoids circular locks, the active change is much
smaller and more reasonably sized.
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
We will reinit DSP in a loop when it fails to initialize the first
time, as recommended. So, it is not an error before we finally give
up. And reorder the trace to make it more readable.
Signed-off-by: Bard liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110235751.3404-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add a state machine for FW boot to track the
different stages of FW boot and replace the boot_complete
field with fw_state field in struct snd_sof_dev.
This will be used to determine the actions to be performed
during system suspend.
One of the main motivations for adding this change is the
fact that errors during the top-level SOF device probe cannot
be propagated and therefore suspending the SOF device normally
during system suspend could potentially run into errors.
For example, with the current flow, if the FW boot failed
for some reason and the system suspends, the SOF device
suspend could fail because the CTX_SAVE IPC would be attempted
even though the FW never really booted successfully causing it
to time out. Another scenario that the state machine fixes
is when the runtime suspend for the SOF device fails and
the DSP is powered down nevertheless, the CTX_SAVE IPC during
system suspend would timeout because the DSP is already
powered down.
Reviewed-by: Curtis Malainey <cujomalainey@chromium.org>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191218002616.7652-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Such traces should be extremely rare but extremely useful for debug.
Report errors for all calls to sdn_sof_dsp_read_poll_timeout(), but
only on negative values for consistency.
Add traces that enable each timeout to be uniquely identified.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022192844.21022-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
If a ROM timeout is detected, we still stop the DMA but will return
the initial error should the DMA stop also fail.
Likewise the cleanup is handled regardless of the status, but we
return the initial error.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022192844.21022-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The "snd_pcm_substream" handle was not initialized properly
in hda-loader.c for firmware load.
When the HDA DMAs were used to load the firmware,
the interrupts related to firmware load also triggered
calls to snd_sof_pcm_period_elapsed() on a non-existent ALSA
PCM stream.
This caused runtime kernel warnings from
pcm_lib.c:snd_pcm_period_elapsed().
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190927200538.660-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
By default, the I2S ports are configured in master mode during
DSP powerup sequences, the FS and BCLK lines will be driven on
startup, even when the topology file explicitly requires the
SSP to be slave.
This may be problematic for external components configured in
master mode who don't expect the Intel SOC/PCH to drive. Fix by
configuring the SSP as slave before the SSP outputs are enabled
to avoid this transient behavior.
When the topology file configures the SSP as clock master, the
initial slave configuration will be overridden.
Signed-off-by: Zhu Yingjiang <yingjiang.zhu@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
Add support for loading DSP firmware on Intel HDA based platforms.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
