summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/mellanox/mlxsw/core.c
Commit message (Collapse)AuthorAgeFilesLines
* mlxsw: core: Add support for using EMAD string TLVShalom Toledo2019-11-121-6/+70
| | | | | | | | | | | | | In case the firmware had an error while processing EMADs, it can send back an ASCII string with the reason using EMAD string TLV. This patch adds the support for using EMAD string TLV. In case of an error, reports the reason using devlink hwerr tracepoint. Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: core: Extend EMAD information reported to devlink hwerrShalom Toledo2019-11-121-2/+10
| | | | | | | | | | Extend EMAD information reported to devlink hwerr tracepoint with transaction id and reg id (both, hex and string). Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: core: Add support for EMAD string TLV parsingShalom Toledo2019-11-121-0/+15
| | | | | | | | | | During parsing of incoming EMADs, fill the string TLV's offset when it is used. Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: core: Add EMAD string TLVShalom Toledo2019-11-121-0/+19
| | | | | | | | | | Add EMAD string TLV, an ASCII string the driver can receive from the firmware in case of an error. Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: core: Parse TLVs' offsets of incoming EMADsShalom Toledo2019-11-121-11/+42
| | | | | | | | | | | | | | | Until now the code assumes a fixed structure which makes it difficult to support EMADs with and without new TLVs. Make it more generic by parsing the TLVs when the EMADs are received and store the offset to the different TLVs in the control block. Using these offsets to extract information from the EMADs without relying on a specific structure. Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: core: Enable devlink reload only on probeJiri Pirko2019-11-111-2/+3
| | | | | | | | | | | Call devlink enable only during probe time and avoid deadlock during reload. Reported-by: Shalom Toledo <shalomt@mellanox.com> Fixes: a0c76345e3d3 ("devlink: disallow reload operation during device cleanup") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Tested-by: Shalom Toledo <shalomt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* devlink: disallow reload operation during device cleanupJiri Pirko2019-11-081-1/+5
| | | | | | | | | | | | | | | | | | | | | There is a race between driver code that does setup/cleanup of device and devlink reload operation that in some drivers works with the same code. Use after free could we easily obtained by running: while true; do echo 10 > /sys/bus/netdevsim/new_device devlink dev reload netdevsim/netdevsim10 & echo 10 > /sys/bus/netdevsim/del_device done Fix this by enabling reload only after setup of device is complete and disabling it at the beginning of the cleanup process. Reported-by: Ido Schimmel <idosch@mellanox.com> Fixes: 2d8dc5bbf4e7 ("devlink: Add support for reload") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller2019-11-021-2/+2
|\ | | | | | | | | | | | | | | | | The only slightly tricky merge conflict was the netdevsim because the mutex locking fix overlapped a lot of driver reload reorganization. The rest were (relatively) trivial in nature. Signed-off-by: David S. Miller <davem@davemloft.net>
| * mlxsw: core: Unpublish devlink parameters during reloadJiri Pirko2019-10-301-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The devlink parameter "acl_region_rehash_interval" is a runtime parameter whose value is stored in a dynamically allocated memory. While reloading the driver, this memory is freed and then allocated again. A use-after-free might happen if during this time frame someone tries to retrieve its value. Since commit 070c63f20f6c ("net: devlink: allow to change namespaces during reload") the use-after-free can be reliably triggered when reloading the driver into a namespace, as after freeing the memory (via reload_down() callback) all the parameters are notified. Fix this by unpublishing and then re-publishing the parameters during reload. Fixes: 98bbf70c1c41 ("mlxsw: spectrum: add "acl_region_rehash_interval" devlink param") Fixes: 7c62cfb8c574 ("devlink: publish params only after driver init is done") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | mlxsw: spectrum: Use PMTM register to get max module widthJiri Pirko2019-10-311-0/+29
| | | | | | | | | | | | | | | | | | | | Currently the max module width is hard-coded according to ASIC type. That is not entirely correct, as the max module width might differ per-board. Use PMTM register to query FW for maximal width of a module. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | mlxsw: core: Push minor/subminor fw version check into helperVadim Pasternak2019-10-061-0/+10
| | | | | | | | | | | | | | | | | | | | | | Add new API for FW "minor" and "subminor" version validation for sharing it between "spectrum" and "minimal" drivers. Use it in "spectrum" driver. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: devlink: allow to change namespaces during reloadJiri Pirko2019-10-041-0/+1
| | | | | | | | | | | | | | | | | | | | | | All devlink instances are created in init_net and stay there for a lifetime. Allow user to be able to move devlink instances into namespaces during devlink reload operation. That ensures proper re-instantiation of driver objects, including netdevices. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | mlxsw: Propagate extack down to register_fib_notifier()Jiri Pirko2019-10-041-5/+8
|/ | | | | | | | During the devlink reaload the extack is present, so propagate it all the way down to register_fib_notifier() call in spectrum_router.c. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: spectrum: Register CPU port with devlinkShalom Toledo2019-09-161-9/+54
| | | | | | | | | Register CPU port with devlink. Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: devlink: move reload fail indication to devlink core and expose to userJiri Pirko2019-09-131-10/+5
| | | | | | | | Currently the fact that devlink reload failed is stored in drivers. Move this flag into devlink core. Also, expose it to the user. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: devlink: split reload op into twoJiri Pirko2019-09-131-4/+15
| | | | | | | | | In order to properly implement failure indication during reload, split the reload op into two ops, one for down phase and one for up phase. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: spectrum: Add devlink-trap supportIdo Schimmel2019-08-211-0/+52
| | | | | | | | | | | | Register supported packet traps (layer 2 drops only, currently) and associated trap group with devlink during driver initialization. The amount of traffic generated by these packet drop traps is capped at 10Kpps to ensure the CPU is not overwhelmed by incoming packets. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: core: Add API to set trap actionIdo Schimmel2019-08-211-0/+12
| | | | | | | | | | Up until now the action of a trap was never changed during its lifetime. This is going to change by subsequent patches that will allow devlink to control the action of certain traps. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: pci: PTP: Hook into packet transmit pathPetr Machata2019-07-011-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | On Spectrum-1, timestamps are delivered separately from the packets, and need to paired up. Therefore, at some point after mlxsw_sp_port_xmit() is invoked, it is necessary to involve the chip-specific driver code to allow it to do the necessary bookkeeping and matching. On Spectrum-2, timestamps are delivered in CQE. For that reason, position the point of driver involvement into mlxsw_pci_cqe_sdq_handle() to make it hopefully easier to extend for Spectrum-2 in the future. To tell the driver what port the packet was sent on, keep tx_info in SKB control buffer. Introduce a new driver core interface mlxsw_core_ptp_transmitted(), a driver callback ptp_transmitted, and a PTP op transmitted. The callee is responsible for taking care of releasing the SKB passed to the new interfaces, and correspondingly have the new stub callbacks just call dev_kfree_skb_any(). Follow-up patches will introduce the actual content into mlxsw_sp1_ptp_transmitted() in particular. Signed-off-by: Petr Machata <petrm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: core: Add a new interface for reading the hardware free running clockShalom Toledo2019-06-131-0/+12
| | | | | | | | | | Add two new bus operations for reading the hardware free running clock. Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: Move firmware flash implementation to devlinkJiri Pirko2019-06-041-0/+15
| | | | | | | | | Benefit from the devlink flash update implementation and ethtool fallback to it and move firmware flash implementation there. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: core: Re-order initialization sequenceIdo Schimmel2019-05-301-10/+11
| | | | | | | | | | | | | | | | | | The driver core first registers with the hwmon and thermal subsystems and only then proceeds to initialize the switch driver (e.g., mlxsw_spectrum). It is only during the last stage that the current firmware version is validated and a newer one flashed, if necessary. The above means that if a new firmware feature is utilized by the hwmon/thermal code, the driver will not be able to load. Solve this by re-ordering initializing the switch driver before registering with the hwmon and thermal subsystems. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Shalom Toledo <shalomt@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: core: Prevent QSFP module initialization for old hardwareVadim Pasternak2019-05-181-0/+6
| | | | | | | | | | | | | | | | Old Mellanox silicons, like switchx-2, switch-ib do not support reading QSFP modules temperature through MTMP register. Attempt to access this register on systems equipped with the this kind of silicon will cause initialization flow failure. Test for hardware resource capability is added in order to distinct between old and new silicon - old silicons do not have such capability. Fixes: 6a79507cfe94 ("mlxsw: core: Extend thermal module with per QSFP module thermal zones") Fixes: 5c42eaa07bd0 ("mlxsw: core: Extend hwmon interface with QSFP module temperature attributes") Reported-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: spectrum_buffers: Add extack messages for invalid configurationsIdo Schimmel2019-04-221-3/+4
| | | | | | | | | | | | | | | | Add extack messages to better communicate invalid configuration to the user. Example: # devlink sb pool set pci/0000:01:00.0 pool 0 size 104857600 thtype dynamic Error: mlxsw_spectrum: Exceeded shared buffer size. devlink answers: Invalid argument Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: devlink: Add extack to shared buffer operationsIdo Schimmel2019-04-221-3/+6
| | | | | | | | | | | Add extack to shared buffer set operations, so that meaningful error messages could be propagated to the user. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Cc: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2019-04-171-3/+3
|\ | | | | | | | | | | Conflict resolution of af_smc.c from Stephen Rothwell. Signed-off-by: David S. Miller <davem@davemloft.net>
| * mlxsw: core: Do not use WQ_MEM_RECLAIM for mlxsw workqueueIdo Schimmel2019-04-101-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The workqueue is used to periodically update the networking stack about activity / statistics of various objects such as neighbours and TC actions. It should not be called as part of memory reclaim path, so remove the WQ_MEM_RECLAIM flag. Fixes: 3d5479e92087 ("mlxsw: core: Remove deprecated create_workqueue") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * mlxsw: core: Do not use WQ_MEM_RECLAIM for mlxsw ordered workqueueIdo Schimmel2019-04-101-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ordered workqueue is used to offload various objects such as routes and neighbours in the order they are notified. It should not be called as part of memory reclaim path, so remove the WQ_MEM_RECLAIM flag. This can also result in a warning [1], if a worker tries to flush a non-WQ_MEM_RECLAIM workqueue. [1] [97703.542861] workqueue: WQ_MEM_RECLAIM mlxsw_core_ordered:mlxsw_sp_router_fib6_event_work [mlxsw_spectrum] is flushing !WQ_MEM_RECLAIM events:rht_deferred_worker [97703.542884] WARNING: CPU: 1 PID: 32492 at kernel/workqueue.c:2605 check_flush_dependency+0xb5/0x130 ... [97703.542988] Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018 [97703.543049] Workqueue: mlxsw_core_ordered mlxsw_sp_router_fib6_event_work [mlxsw_spectrum] [97703.543061] RIP: 0010:check_flush_dependency+0xb5/0x130 ... [97703.543071] RSP: 0018:ffffb3f08137bc00 EFLAGS: 00010086 [97703.543076] RAX: 0000000000000000 RBX: ffff96e07740ae00 RCX: 0000000000000000 [97703.543080] RDX: 0000000000000094 RSI: ffffffff82dc1934 RDI: 0000000000000046 [97703.543084] RBP: ffffb3f08137bc20 R08: ffffffff82dc18a0 R09: 00000000000225c0 [97703.543087] R10: 0000000000000000 R11: 0000000000007eec R12: ffffffff816e4ee0 [97703.543091] R13: ffff96e06f6a5c00 R14: ffff96e077ba7700 R15: ffffffff812ab0c0 [97703.543097] FS: 0000000000000000(0000) GS:ffff96e077a80000(0000) knlGS:0000000000000000 [97703.543101] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [97703.543104] CR2: 00007f8cd135b280 CR3: 00000001e860e003 CR4: 00000000003606e0 [97703.543109] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [97703.543112] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [97703.543115] Call Trace: [97703.543129] __flush_work+0xbd/0x1e0 [97703.543137] ? __cancel_work_timer+0x136/0x1b0 [97703.543145] ? pwq_dec_nr_in_flight+0x49/0xa0 [97703.543154] __cancel_work_timer+0x136/0x1b0 [97703.543175] ? mlxsw_reg_trans_bulk_wait+0x145/0x400 [mlxsw_core] [97703.543184] cancel_work_sync+0x10/0x20 [97703.543191] rhashtable_free_and_destroy+0x23/0x140 [97703.543198] rhashtable_destroy+0xd/0x10 [97703.543254] mlxsw_sp_fib_destroy+0xb1/0xf0 [mlxsw_spectrum] [97703.543310] mlxsw_sp_vr_put+0xa8/0xc0 [mlxsw_spectrum] [97703.543364] mlxsw_sp_fib_node_put+0xbf/0x140 [mlxsw_spectrum] [97703.543418] ? mlxsw_sp_fib6_entry_destroy+0xe8/0x110 [mlxsw_spectrum] [97703.543475] mlxsw_sp_router_fib6_event_work+0x6cd/0x7f0 [mlxsw_spectrum] [97703.543484] process_one_work+0x1fd/0x400 [97703.543493] worker_thread+0x34/0x410 [97703.543500] kthread+0x121/0x140 [97703.543507] ? process_one_work+0x400/0x400 [97703.543512] ? kthread_park+0x90/0x90 [97703.543523] ret_from_fork+0x35/0x40 Fixes: a3832b31898f ("mlxsw: core: Create an ordered workqueue for FIB offload") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Semion Lisyansky <semionl@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * mlxsw: core: Do not use WQ_MEM_RECLAIM for EMAD workqueueIdo Schimmel2019-04-101-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The EMAD workqueue is used to handle retransmission of EMAD packets that contain configuration data for the device's firmware. Given the workers need to allocate these packets and that the code is not called as part of memory reclaim path, remove the WQ_MEM_RECLAIM flag. Fixes: d965465b60ba ("mlxsw: core: Fix possible deadlock") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | mlxsw: core: Add support for devlink info commandShalom Toledo2019-04-081-0/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Expose the following ASIC information via devlink info command: - Driver name - Hardware revision - Firmware PSID - Running firmware version Standard output example: $ devlink dev info pci/0000:03:00.0 pci/0000:03:00.0: driver mlxsw_spectrum versions: fixed: hw.revision A0 fw.psid MT_2750110033 running: fw.version 13.1910.622 Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | mlxsw: Pass switch ID through devlink_port_attrs_set()Jiri Pirko2019-04-041-2/+4
| | | | | | | | | | | | | | | | Pass the switch ID down the to devlink through devlink_port_attrs_set() so it can be used by devlink_compat_switch_id_get(). Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: devlink: extend port attrs for switch IDJiri Pirko2019-04-041-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | Extend devlink_port_attrs_set() to pass switch ID for ports which are part of switch and store it in port attrs. For other ports, this is NULL. Note that this allows the driver to group devlink ports into one or more switches according to the actual topology. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | mlxsw: Remove ndo_get_phys_port_name implementationJiri Pirko2019-03-281-10/+0
| | | | | | | | | | | | | | | | | | Rely on the previously introduced fallback and let the core call devlink directly in order to get the physical port name. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | mlxsw: Implement ndo_get_devlink_portJiri Pirko2019-03-281-0/+12
| | | | | | | | | | | | | | | | In order for devlink compat functions to work, implement ndo_get_devlink_port. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | mlxsw: Move devlink_port_attrs_set() call before registerJiri Pirko2019-03-241-6/+6
|/ | | | | | | | Since attrs are static during the existence of devlink port, set the before registration of the port. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: core: Move resource query API to common locationVadim Pasternak2019-03-031-0/+37
| | | | | | | | | | | Move mlxsw_pci_resources_query() to a common location to allow reuse by the different drivers and over all the supported physical buses. Rename it to mlxsw_core_resources_query(). Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* devlink: publish params only after driver init is doneJiri Pirko2019-02-081-0/+5
| | | | | | | | | | | | | | | | | Currently, user can do dump or get of param values right after the devlink params are registered. However the driver may not be initialized which is an issue. The same problem happens during notification upon param registration. Allow driver to publish devlink params whenever it is ready to handle get() ops. Note that this cannot be resolved by init reordering, as the "driverinit" params have to be available before the driver is initialized (it needs the param values there). Signed-off-by: Jiri Pirko <jiri@mellanox.com> Cc: Michael Chan <michael.chan@broadcom.com> Cc: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: core: Trace EMAD errorsNir Dotan2019-02-061-1/+5
| | | | | | | | | Trace EMAD errors returned from HW. Signed-off-by: Nir Dotan <nird@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2018-12-201-1/+18
|\ | | | | | | | | | | | | | | | | | | Lots of conflicts, by happily all cases of overlapping changes, parallel adds, things of that nature. Thanks to Stephen Rothwell, Saeed Mahameed, and others for their guidance in these resolutions. Signed-off-by: David S. Miller <davem@davemloft.net>
| * mlxsw: core: Increase timeout during firmware flash processShalom Toledo2018-12-181-1/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | During the firmware flash process, some of the EMADs get timed out, which causes the driver to send them again with a limit of 5 retries. There are some situations in which 5 retries is not enough and the EMAD access fails. If the failed EMAD was related to the flashing process, the driver fails the flashing. The reason for these timeouts during firmware flashing is cache misses in the CPU running the firmware. In case the CPU needs to fetch instructions from the flash when a firmware is flashed, it needs to wait for the flashing to complete. Since flashing takes time, it is possible for pending EMADs to timeout. Fix by increasing EMADs' timeout while flashing firmware. Fixes: ce6ef68f433f ("mlxsw: spectrum: Implement the ethtool flash_device callback") Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | mlxsw: spectrum: Load firmware version based on devlink parameterShalom Toledo2018-12-031-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Load firmware version based on 'fw_load_policy' devlink parameter. The driver supports these two options: * DEVLINK_PARAM_FW_LOAD_POLICY_VALUE_DRIVER (0) Default, load firmware version preferred by the driver * DEVLINK_PARAM_FW_LOAD_POLICY_VALUE_FLASH (1) Load firmware currently stored in flash The second option, 'flash', allow the device to run with different firmware version than preferred by the driver for testing and/or debugging purposes. For example, testing a firmware bug fix. Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | mlxsw: core: Reset firmware after flash during driver initializationShalom Toledo2018-12-031-4/+28
|/ | | | | | | | | | | After flashing new firmware during the driver initialization flow (reload or not), the driver should do a firmware reset when it gets -EAGAIN in order to load the new one. Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: core: Fix devlink unregister flowShalom Toledo2018-10-291-7/+17
| | | | | | | | | | | | | | | | | After a failed reload, the driver is still registered to devlink, its devlink instance is still allocated and the 'reload_fail' flag is set. Then, in the next reload try, the driver's allocated devlink instance will be freed without unregistering from devlink and its components (e.g, resources). This scenario can cause a use-after-free if the user tries to execute command via devlink user-space tool. Fix by not freeing the devlink instance during reload (failed or not). Fixes: 24cc68ad6c46 ("mlxsw: core: Add support for reload") Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: core: Fix use-after-free when flashing firmware during initIdo Schimmel2018-10-171-0/+2
| | | | | | | | | | | | | | | | | | | | | | When the switch driver (e.g., mlxsw_spectrum) determines it needs to flash a new firmware version it resets the ASIC after the flashing process. The bus driver (e.g., mlxsw_pci) then registers itself again with mlxsw_core which means (among other things) that the device registers itself again with the hwmon subsystem again. Since the device was registered with the hwmon subsystem using devm_hwmon_device_register_with_groups(), then the old hwmon device (registered before the flashing) was never unregistered and was referencing stale data, resulting in a use-after free. Fix by removing reliance on device managed APIs in mlxsw_hwmon_init(). Fixes: c86d62cc410c ("mlxsw: spectrum: Reset FW after flash") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Alexander Petrovskiy <alexpe@mellanox.com> Tested-by: Alexander Petrovskiy <alexpe@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: core: remove unnecessary function mlxsw_core_driver_putYueHaibing2018-08-101-12/+0
| | | | | | | | | | The function mlxsw_core_driver_put only traverse mlxsw_core_driver_list to find the matched mlxsw_driver,but never used it. So it can be removed safely. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: Replace license text with SPDX identifiers and adjust copyrightsJiri Pirko2018-08-091-35/+2
| | | | | | Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: Add extack messages for port_{un, }split failuresDavid Ahern2018-06-051-4/+10
| | | | | | | | | | | | | | | | Return messages in extack for port split/unsplit errors. e.g., $ devlink port split swp1s1 count 4 Error: mlxsw_spectrum: Port cannot be split further. devlink answers: Invalid argument $ devlink port unsplit swp4 Error: mlxsw_spectrum: Port was not split. devlink answers: Invalid argument Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* devlink: Add extack to reload and port_{un, }split operationsDavid Ahern2018-06-051-3/+6
| | | | | | | | Add extack argument to reload, port_split and port_unsplit operations. Signed-off-by: David Ahern <dsahern@gmail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: pci: Utilize MRSR register to perform FW resetJiri Pirko2018-05-291-3/+1
| | | | | | | | | | | | | So far, the PCI BAR0 register is used for triggering FW reset. However, that is a legacy attitude and it is recommended to use MRSR to perform reset instead. So do that. Move the reset into init() function as the cmd interface needs to be used. With that, IRQ initialization needs to be moved as well. As a side effect, the reset move simplifies the devlink reload flow. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: cmd: Handle error after reset gracefullyJiri Pirko2018-05-291-7/+19
| | | | | | | | | | | There is an exception in command interface processing in case the MRSR register is written to. The register triggers FW reset and during the reset FW returns an error. So handle this by ignoring this error while writing to MRSR register. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
OpenPOWER on IntegriCloud