diff options
Diffstat (limited to 'drivers/tty/serial/amba-pl011.c')
| -rw-r--r-- | drivers/tty/serial/amba-pl011.c | 30 |
1 files changed, 8 insertions, 22 deletions
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c index 5921a33b2a07..2296bb0f9578 100644 --- a/drivers/tty/serial/amba-pl011.c +++ b/drivers/tty/serial/amba-pl011.c @@ -16,11 +16,6 @@ * and hooked into this driver. */ - -#if defined(CONFIG_SERIAL_AMBA_PL011_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) -#define SUPPORT_SYSRQ -#endif - #include <linux/module.h> #include <linux/ioport.h> #include <linux/init.h> @@ -414,7 +409,7 @@ static void pl011_dma_probe(struct uart_amba_port *uap) dma_cap_mask_t mask; uap->dma_probed = true; - chan = dma_request_slave_channel_reason(dev, "tx"); + chan = dma_request_chan(dev, "tx"); if (IS_ERR(chan)) { if (PTR_ERR(chan) == -EPROBE_DEFER) { uap->dma_probed = false; @@ -813,10 +808,8 @@ __acquires(&uap->port.lock) if (!uap->using_tx_dma) return; - /* Avoid deadlock with the DMA engine callback */ - spin_unlock(&uap->port.lock); - dmaengine_terminate_all(uap->dmatx.chan); - spin_lock(&uap->port.lock); + dmaengine_terminate_async(uap->dmatx.chan); + if (uap->dmatx.queued) { dma_unmap_sg(uap->dmatx.chan->device->dev, &uap->dmatx.sg, 1, DMA_TO_DEVICE); @@ -1236,10 +1229,6 @@ static inline bool pl011_dma_rx_running(struct uart_amba_port *uap) #else /* Blank functions if the DMA engine is not available */ -static inline void pl011_dma_probe(struct uart_amba_port *uap) -{ -} - static inline void pl011_dma_remove(struct uart_amba_port *uap) { } @@ -1458,8 +1447,6 @@ static void pl011_modem_status(struct uart_amba_port *uap) static void check_apply_cts_event_workaround(struct uart_amba_port *uap) { - unsigned int dummy_read; - if (!uap->vendor->cts_event_workaround) return; @@ -1471,8 +1458,8 @@ static void check_apply_cts_event_workaround(struct uart_amba_port *uap) * single apb access will incur 2 pclk(133.12Mhz) delay, * so add 2 dummy reads */ - dummy_read = pl011_read(uap, REG_ICR); - dummy_read = pl011_read(uap, REG_ICR); + pl011_read(uap, REG_ICR); + pl011_read(uap, REG_ICR); } static irqreturn_t pl011_int(int irq, void *dev_id) @@ -2585,6 +2572,7 @@ static int pl011_setup_port(struct device *dev, struct uart_amba_port *uap, uap->port.mapbase = mmiobase->start; uap->port.membase = base; uap->port.fifosize = uap->fifosize; + uap->port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_AMBA_PL011_CONSOLE); uap->port.flags = UPF_BOOT_AUTOCONF; uap->port.line = index; @@ -2718,11 +2706,8 @@ static int sbsa_uart_probe(struct platform_device *pdev) return -ENOMEM; ret = platform_get_irq(pdev, 0); - if (ret < 0) { - if (ret != -EPROBE_DEFER) - dev_err(&pdev->dev, "cannot obtain irq\n"); + if (ret < 0) return ret; - } uap->port.irq = ret; #ifdef CONFIG_ACPI_SPCR_TABLE @@ -2778,6 +2763,7 @@ static struct platform_driver arm_sbsa_uart_platform_driver = { .remove = sbsa_uart_remove, .driver = { .name = "sbsa-uart", + .pm = &pl011_dev_pm_ops, .of_match_table = of_match_ptr(sbsa_uart_of_match), .acpi_match_table = ACPI_PTR(sbsa_uart_acpi_match), .suppress_bind_attrs = IS_BUILTIN(CONFIG_SERIAL_AMBA_PL011), |
