summaryrefslogtreecommitdiffstats
path: root/arch/arm/mach-bcmring/include/mach/reg_umi.h
diff options
context:
space:
mode:
Diffstat (limited to 'arch/arm/mach-bcmring/include/mach/reg_umi.h')
-rw-r--r--arch/arm/mach-bcmring/include/mach/reg_umi.h237
1 files changed, 0 insertions, 237 deletions
diff --git a/arch/arm/mach-bcmring/include/mach/reg_umi.h b/arch/arm/mach-bcmring/include/mach/reg_umi.h
deleted file mode 100644
index 0992842caa77..000000000000
--- a/arch/arm/mach-bcmring/include/mach/reg_umi.h
+++ /dev/null
@@ -1,237 +0,0 @@
-/*****************************************************************************
-* Copyright 2005 - 2008 Broadcom Corporation. All rights reserved.
-*
-* Unless you and Broadcom execute a separate written software license
-* agreement governing use of this software, this software is licensed to you
-* under the terms of the GNU General Public License version 2, available at
-* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-*
-* Notwithstanding the above, under no circumstances may you combine this
-* software in any way with any other Broadcom software provided under a
-* license other than the GPL, without Broadcom's express prior written
-* consent.
-*****************************************************************************/
-
-/*
-*
-*****************************************************************************
-*
-* REG_UMI.h
-*
-* PURPOSE:
-*
-* This file contains definitions for the nand registers:
-*
-* NOTES:
-*
-*****************************************************************************/
-
-#if !defined(__ASM_ARCH_REG_UMI_H)
-#define __ASM_ARCH_REG_UMI_H
-
-/* ---- Include Files ---------------------------------------------------- */
-#include <csp/reg.h>
-#include <mach/csp/mm_io.h>
-
-/* ---- Constants and Types ---------------------------------------------- */
-
-/* Unified Memory Interface Ctrl Register */
-#define HW_UMI_BASE MM_IO_BASE_UMI
-
-/* Flash bank 0 timing and control register */
-#define REG_UMI_FLASH0_TCR __REG32(HW_UMI_BASE + 0x00)
-/* Flash bank 1 timing and control register */
-#define REG_UMI_FLASH1_TCR __REG32(HW_UMI_BASE + 0x04)
-/* Flash bank 2 timing and control register */
-#define REG_UMI_FLASH2_TCR __REG32(HW_UMI_BASE + 0x08)
-/* MMD interface and control register */
-#define REG_UMI_MMD_ICR __REG32(HW_UMI_BASE + 0x0c)
-/* NAND timing and control register */
-#define REG_UMI_NAND_TCR __REG32(HW_UMI_BASE + 0x18)
-/* NAND ready/chip select register */
-#define REG_UMI_NAND_RCSR __REG32(HW_UMI_BASE + 0x1c)
-/* NAND ECC control & status register */
-#define REG_UMI_NAND_ECC_CSR __REG32(HW_UMI_BASE + 0x20)
-/* NAND ECC data register XXB2B1B0 */
-#define REG_UMI_NAND_ECC_DATA __REG32(HW_UMI_BASE + 0x24)
-/* BCH ECC Parameter N */
-#define REG_UMI_BCH_N __REG32(HW_UMI_BASE + 0x40)
-/* BCH ECC Parameter T */
-#define REG_UMI_BCH_K __REG32(HW_UMI_BASE + 0x44)
-/* BCH ECC Parameter K */
-#define REG_UMI_BCH_T __REG32(HW_UMI_BASE + 0x48)
-/* BCH ECC Contro Status */
-#define REG_UMI_BCH_CTRL_STATUS __REG32(HW_UMI_BASE + 0x4C)
-/* BCH WR ECC 31:0 */
-#define REG_UMI_BCH_WR_ECC_0 __REG32(HW_UMI_BASE + 0x50)
-/* BCH WR ECC 63:32 */
-#define REG_UMI_BCH_WR_ECC_1 __REG32(HW_UMI_BASE + 0x54)
-/* BCH WR ECC 95:64 */
-#define REG_UMI_BCH_WR_ECC_2 __REG32(HW_UMI_BASE + 0x58)
-/* BCH WR ECC 127:96 */
-#define REG_UMI_BCH_WR_ECC_3 __REG32(HW_UMI_BASE + 0x5c)
-/* BCH WR ECC 155:128 */
-#define REG_UMI_BCH_WR_ECC_4 __REG32(HW_UMI_BASE + 0x60)
-/* BCH Read Error Location 1,0 */
-#define REG_UMI_BCH_RD_ERR_LOC_1_0 __REG32(HW_UMI_BASE + 0x64)
-/* BCH Read Error Location 3,2 */
-#define REG_UMI_BCH_RD_ERR_LOC_3_2 __REG32(HW_UMI_BASE + 0x68)
-/* BCH Read Error Location 5,4 */
-#define REG_UMI_BCH_RD_ERR_LOC_5_4 __REG32(HW_UMI_BASE + 0x6c)
-/* BCH Read Error Location 7,6 */
-#define REG_UMI_BCH_RD_ERR_LOC_7_6 __REG32(HW_UMI_BASE + 0x70)
-/* BCH Read Error Location 9,8 */
-#define REG_UMI_BCH_RD_ERR_LOC_9_8 __REG32(HW_UMI_BASE + 0x74)
-/* BCH Read Error Location 11,10 */
-#define REG_UMI_BCH_RD_ERR_LOC_B_A __REG32(HW_UMI_BASE + 0x78)
-
-/* REG_UMI_FLASH0/1/2_TCR, REG_UMI_SRAM0/1_TCR bits */
-/* Enable wait pin during burst write or read */
-#define REG_UMI_TCR_WAITEN 0x80000000
-/* Enable mem ctrlr to work with ext mem of lower freq than AHB clk */
-#define REG_UMI_TCR_LOWFREQ 0x40000000
-/* 1=synch write, 0=async write */
-#define REG_UMI_TCR_MEMTYPE_SYNCWRITE 0x20000000
-/* 1=synch read, 0=async read */
-#define REG_UMI_TCR_MEMTYPE_SYNCREAD 0x10000000
-/* 1=page mode read, 0=normal mode read */
-#define REG_UMI_TCR_MEMTYPE_PAGEREAD 0x08000000
-/* page size/burst size (wrap only) */
-#define REG_UMI_TCR_MEMTYPE_PGSZ_MASK 0x07000000
-/* 4 word */
-#define REG_UMI_TCR_MEMTYPE_PGSZ_4 0x00000000
-/* 8 word */
-#define REG_UMI_TCR_MEMTYPE_PGSZ_8 0x01000000
-/* 16 word */
-#define REG_UMI_TCR_MEMTYPE_PGSZ_16 0x02000000
-/* 32 word */
-#define REG_UMI_TCR_MEMTYPE_PGSZ_32 0x03000000
-/* 64 word */
-#define REG_UMI_TCR_MEMTYPE_PGSZ_64 0x04000000
-/* 128 word */
-#define REG_UMI_TCR_MEMTYPE_PGSZ_128 0x05000000
-/* 256 word */
-#define REG_UMI_TCR_MEMTYPE_PGSZ_256 0x06000000
-/* 512 word */
-#define REG_UMI_TCR_MEMTYPE_PGSZ_512 0x07000000
-/* Page read access cycle / Burst write latency (n+2 / n+1) */
-#define REG_UMI_TCR_TPRC_TWLC_MASK 0x00f80000
-/* Bus turnaround cycle (n) */
-#define REG_UMI_TCR_TBTA_MASK 0x00070000
-/* Write pulse width cycle (n+1) */
-#define REG_UMI_TCR_TWP_MASK 0x0000f800
-/* Write recovery cycle (n+1) */
-#define REG_UMI_TCR_TWR_MASK 0x00000600
-/* Write address setup cycle (n+1) */
-#define REG_UMI_TCR_TAS_MASK 0x00000180
-/* Output enable delay cycle (n) */
-#define REG_UMI_TCR_TOE_MASK 0x00000060
-/* Read access cycle / Burst read latency (n+2 / n+1) */
-#define REG_UMI_TCR_TRC_TLC_MASK 0x0000001f
-
-/* REG_UMI_MMD_ICR bits */
-/* Flash write protection pin control */
-#define REG_UMI_MMD_ICR_FLASH_WP 0x8000
-/* Extend hold time for sram0, sram1 csn (39 MHz operation) */
-#define REG_UMI_MMD_ICR_XHCS 0x4000
-/* Enable SDRAM 2 interface control */
-#define REG_UMI_MMD_ICR_SDRAM2EN 0x2000
-/* Enable merge of flash banks 0/1 to 512 MBit bank */
-#define REG_UMI_MMD_ICR_INST512 0x1000
-/* Enable merge of flash banks 1/2 to 512 MBit bank */
-#define REG_UMI_MMD_ICR_DATA512 0x0800
-/* Enable SDRAM interface control */
-#define REG_UMI_MMD_ICR_SDRAMEN 0x0400
-/* Polarity of busy state of Burst Wait Signal */
-#define REG_UMI_MMD_ICR_WAITPOL 0x0200
-/* Enable burst clock stopped when not accessing external burst flash/sram */
-#define REG_UMI_MMD_ICR_BCLKSTOP 0x0100
-/* Enable the peri1_csn to replace flash1_csn in 512 Mb flash mode */
-#define REG_UMI_MMD_ICR_PERI1EN 0x0080
-/* Enable the peri2_csn to replace sdram_csn */
-#define REG_UMI_MMD_ICR_PERI2EN 0x0040
-/* Enable the peri3_csn to replace sdram2_csn */
-#define REG_UMI_MMD_ICR_PERI3EN 0x0020
-/* Enable sram bank1 for H/W controlled MRS */
-#define REG_UMI_MMD_ICR_MRSB1 0x0010
-/* Enable sram bank0 for H/W controlled MRS */
-#define REG_UMI_MMD_ICR_MRSB0 0x0008
-/* Polarity for assert3ed state of H/W controlled MRS */
-#define REG_UMI_MMD_ICR_MRSPOL 0x0004
-/* 0: S/W controllable ZZ/MRS/CRE/P-Mode pin */
-/* 1: H/W controlled ZZ/MRS/CRE/P-Mode, same timing as CS */
-#define REG_UMI_MMD_ICR_MRSMODE 0x0002
-/* MRS state for S/W controlled mode */
-#define REG_UMI_MMD_ICR_MRSSTATE 0x0001
-
-/* REG_UMI_NAND_TCR bits */
-/* Enable software to control CS */
-#define REG_UMI_NAND_TCR_CS_SWCTRL 0x80000000
-/* 16-bit nand wordsize if set */
-#define REG_UMI_NAND_TCR_WORD16 0x40000000
-/* Bus turnaround cycle (n) */
-#define REG_UMI_NAND_TCR_TBTA_MASK 0x00070000
-/* Write pulse width cycle (n+1) */
-#define REG_UMI_NAND_TCR_TWP_MASK 0x0000f800
-/* Write recovery cycle (n+1) */
-#define REG_UMI_NAND_TCR_TWR_MASK 0x00000600
-/* Write address setup cycle (n+1) */
-#define REG_UMI_NAND_TCR_TAS_MASK 0x00000180
-/* Output enable delay cycle (n) */
-#define REG_UMI_NAND_TCR_TOE_MASK 0x00000060
-/* Read access cycle (n+2) */
-#define REG_UMI_NAND_TCR_TRC_TLC_MASK 0x0000001f
-
-/* REG_UMI_NAND_RCSR bits */
-/* Status: Ready=1, Busy=0 */
-#define REG_UMI_NAND_RCSR_RDY 0x02
-/* Keep CS asserted during operation */
-#define REG_UMI_NAND_RCSR_CS_ASSERTED 0x01
-
-/* REG_UMI_NAND_ECC_CSR bits */
-/* Interrupt status - read-only */
-#define REG_UMI_NAND_ECC_CSR_NANDINT 0x80000000
-/* Read: Status of ECC done, Write: clear ECC interrupt */
-#define REG_UMI_NAND_ECC_CSR_ECCINT_RAW 0x00800000
-/* Read: Status of R/B, Write: clear R/B interrupt */
-#define REG_UMI_NAND_ECC_CSR_RBINT_RAW 0x00400000
-/* 1 = Enable ECC Interrupt */
-#define REG_UMI_NAND_ECC_CSR_ECCINT_ENABLE 0x00008000
-/* 1 = Assert interrupt at rising edge of R/B_ */
-#define REG_UMI_NAND_ECC_CSR_RBINT_ENABLE 0x00004000
-/* Calculate ECC by 0=512 bytes, 1=256 bytes */
-#define REG_UMI_NAND_ECC_CSR_256BYTE 0x00000080
-/* Enable ECC in hardware */
-#define REG_UMI_NAND_ECC_CSR_ECC_ENABLE 0x00000001
-
-/* REG_UMI_BCH_CTRL_STATUS bits */
-/* Shift to Indicate Number of correctable errors detected */
-#define REG_UMI_BCH_CTRL_STATUS_NB_CORR_ERROR_SHIFT 20
-/* Indicate Number of correctable errors detected */
-#define REG_UMI_BCH_CTRL_STATUS_NB_CORR_ERROR 0x00F00000
-/* Indicate Errors detected during read but uncorrectable */
-#define REG_UMI_BCH_CTRL_STATUS_UNCORR_ERR 0x00080000
-/* Indicate Errors detected during read and are correctable */
-#define REG_UMI_BCH_CTRL_STATUS_CORR_ERR 0x00040000
-/* Flag indicates BCH's ECC status of read process are valid */
-#define REG_UMI_BCH_CTRL_STATUS_RD_ECC_VALID 0x00020000
-/* Flag indicates BCH's ECC status of write process are valid */
-#define REG_UMI_BCH_CTRL_STATUS_WR_ECC_VALID 0x00010000
-/* Pause ECC calculation */
-#define REG_UMI_BCH_CTRL_STATUS_PAUSE_ECC_DEC 0x00000010
-/* Enable Interrupt */
-#define REG_UMI_BCH_CTRL_STATUS_INT_EN 0x00000004
-/* Enable ECC during read */
-#define REG_UMI_BCH_CTRL_STATUS_ECC_RD_EN 0x00000002
-/* Enable ECC during write */
-#define REG_UMI_BCH_CTRL_STATUS_ECC_WR_EN 0x00000001
-/* Mask for location */
-#define REG_UMI_BCH_ERR_LOC_MASK 0x00001FFF
-/* location within a byte */
-#define REG_UMI_BCH_ERR_LOC_BYTE 0x00000007
-/* location within a word */
-#define REG_UMI_BCH_ERR_LOC_WORD 0x00000018
-/* location within a page (512 byte) */
-#define REG_UMI_BCH_ERR_LOC_PAGE 0x00001FE0
-#define REG_UMI_BCH_ERR_LOC_ADDR(index) (__REG32(HW_UMI_BASE + 0x64 + (index / 2)*4) >> ((index % 2) * 16))
-#endif
OpenPOWER on IntegriCloud