diff options
Diffstat (limited to 'Documentation/devicetree')
7 files changed, 75 insertions, 2 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gateworks,pld-gpio.txt b/Documentation/devicetree/bindings/gpio/gateworks,pld-gpio.txt new file mode 100644 index 000000000000..6e81f8b755c5 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gateworks,pld-gpio.txt @@ -0,0 +1,20 @@ +Gateworks PLD GPIO controller bindings + +The GPIO controller should be a child node on an I2C bus, +see: i2c/i2c.txt for details. + +Required properties: +- compatible: Should be "gateworks,pld-gpio" +- reg: I2C slave address +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be <2>. The first cell is the gpio number and + the second cell is used to specify optional parameters. + +Example: + +pld@56 { + compatible = "gateworks,pld-gpio"; + reg = <0x56>; + gpio-controller; + #gpio-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-eic-sprd.txt b/Documentation/devicetree/bindings/gpio/gpio-eic-sprd.txt index 93d98d09d92b..54040a2bfe3a 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-eic-sprd.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-eic-sprd.txt @@ -33,7 +33,7 @@ Required properties: "sprd,sc9860-eic-latch", "sprd,sc9860-eic-async", "sprd,sc9860-eic-sync", - "sprd,sc27xx-eic". + "sprd,sc2731-eic". - reg: Define the base and range of the I/O address space containing the GPIO controller registers. - gpio-controller: Marks the device node as a GPIO controller. @@ -86,7 +86,7 @@ Example: }; pmic_eic: gpio@300 { - compatible = "sprd,sc27xx-eic"; + compatible = "sprd,sc2731-eic"; reg = <0x300>; interrupt-parent = <&sc2731_pmic>; interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt index 4e3c550e319a..fb144e2b6522 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt @@ -16,6 +16,7 @@ Required properties: nxp,pca9574 nxp,pca9575 nxp,pca9698 + nxp,pcal6416 nxp,pcal6524 nxp,pcal9555a maxim,max7310 diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index f0ba154b5723..a8895d339bfe 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -67,6 +67,18 @@ Optional standard bitfield specifiers for the last cell: https://en.wikipedia.org/wiki/Open_collector - Bit 3: 0 means the output should be maintained during sleep/low-power mode 1 means the output state can be lost during sleep/low-power mode +- Bit 4: 0 means no pull-up resistor should be enabled + 1 means a pull-up resistor should be enabled + This setting only applies to hardware with a simple on/off + control for pull-up configuration. If the hardware has more + elaborate pull-up configuration, it should be represented + using a pin control binding. +- Bit 5: 0 means no pull-down resistor should be enabled + 1 means a pull-down resistor should be enabled + This setting only applies to hardware with a simple on/off + control for pull-down configuration. If the hardware has more + elaborate pull-down configuration, it should be represented + using a pin control binding. 1.1) GPIO specifier best practices ---------------------------------- diff --git a/Documentation/devicetree/bindings/gpio/intel,ixp4xx-gpio.txt b/Documentation/devicetree/bindings/gpio/intel,ixp4xx-gpio.txt new file mode 100644 index 000000000000..8dc41ed99685 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/intel,ixp4xx-gpio.txt @@ -0,0 +1,38 @@ +Intel IXP4xx XScale Networking Processors GPIO + +This GPIO controller is found in the Intel IXP4xx processors. +It supports 16 GPIO lines. + +The interrupt portions of the GPIO controller is hierarchical: +the synchronous edge detector is part of the GPIO block, but the +actual enabling/disabling of the interrupt line is done in the +main IXP4xx interrupt controller which has a 1:1 mapping for +the first 12 GPIO lines to 12 system interrupts. + +The remaining 4 GPIO lines can not be used for receiving +interrupts. + +The interrupt parent of this GPIO controller must be the +IXP4xx interrupt controller. + +Required properties: + +- compatible : Should be + "intel,ixp4xx-gpio" +- reg : Should contain registers location and length +- gpio-controller : marks this as a GPIO controller +- #gpio-cells : Should be 2, see gpio/gpio.txt +- interrupt-controller : marks this as an interrupt controller +- #interrupt-cells : a standard two-cell interrupt, see + interrupt-controller/interrupts.txt + +Example: + +gpio0: gpio@c8004000 { + compatible = "intel,ixp4xx-gpio"; + reg = <0xc8004000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt index 759aa1732e48..7f64a7e92c28 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt @@ -19,6 +19,7 @@ PMIC's from Qualcomm. "qcom,pm8998-gpio" "qcom,pma8084-gpio" "qcom,pmi8994-gpio" + "qcom,pmi8998-gpio" "qcom,pms405-gpio" And must contain either "qcom,spmi-gpio" or "qcom,ssbi-gpio" diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index aaa18bb1a9f4..385d22460b1d 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -145,6 +145,7 @@ focaltech FocalTech Systems Co.,Ltd friendlyarm Guangzhou FriendlyARM Computer Tech Co., Ltd fsl Freescale Semiconductor fujitsu Fujitsu Ltd. +gateworks Gateworks Corporation gcw Game Consoles Worldwide ge General Electric Company geekbuying GeekBuying |
