diff options
Diffstat (limited to 'Documentation/devicetree/bindings/media/i2c')
4 files changed, 81 insertions, 8 deletions
diff --git a/Documentation/devicetree/bindings/media/i2c/ad5820.txt b/Documentation/devicetree/bindings/media/i2c/ad5820.txt index 5940ca11c021..5764cbedf9b7 100644 --- a/Documentation/devicetree/bindings/media/i2c/ad5820.txt +++ b/Documentation/devicetree/bindings/media/i2c/ad5820.txt @@ -2,12 +2,20 @@ Required Properties: - - compatible: Must contain "adi,ad5820" + - compatible: Must contain one of: + - "adi,ad5820" + - "adi,ad5821" + - "adi,ad5823" - reg: I2C slave address - VANA-supply: supply of voltage for VANA pin +Optional properties: + + - enable-gpios : GPIO spec for the XSHUTDOWN pin. The XSHUTDOWN signal is +active low, a high level on the pin enables the device. + Example: ad5820: coil@c { @@ -15,5 +23,6 @@ Example: reg = <0x0c>; VANA-supply = <&vaux4>; + enable-gpios = <&msmgpio 26 GPIO_ACTIVE_HIGH>; }; diff --git a/Documentation/devicetree/bindings/media/i2c/imx290.txt b/Documentation/devicetree/bindings/media/i2c/imx290.txt new file mode 100644 index 000000000000..a3cc21410f7c --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/imx290.txt @@ -0,0 +1,57 @@ +* Sony IMX290 1/2.8-Inch CMOS Image Sensor + +The Sony IMX290 is a 1/2.8-Inch CMOS Solid-state image sensor with +Square Pixel for Color Cameras. It is programmable through I2C and 4-wire +interfaces. The sensor output is available via CMOS logic parallel SDR output, +Low voltage LVDS DDR output and CSI-2 serial data output. The CSI-2 bus is the +default. No bindings have been defined for the other busses. + +Required Properties: +- compatible: Should be "sony,imx290" +- reg: I2C bus address of the device +- clocks: Reference to the xclk clock. +- clock-names: Should be "xclk". +- clock-frequency: Frequency of the xclk clock in Hz. +- vdddo-supply: Sensor digital IO regulator. +- vdda-supply: Sensor analog regulator. +- vddd-supply: Sensor digital core regulator. + +Optional Properties: +- reset-gpios: Sensor reset GPIO + +The imx290 device node should contain one 'port' child node with +an 'endpoint' subnode. For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Required Properties on endpoint: +- data-lanes: check ../video-interfaces.txt +- link-frequencies: check ../video-interfaces.txt +- remote-endpoint: check ../video-interfaces.txt + +Example: + &i2c1 { + ... + imx290: camera-sensor@1a { + compatible = "sony,imx290"; + reg = <0x1a>; + + reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&camera_rear_default>; + + clocks = <&gcc GCC_CAMSS_MCLK0_CLK>; + clock-names = "xclk"; + clock-frequency = <37125000>; + + vdddo-supply = <&camera_vdddo_1v8>; + vdda-supply = <&camera_vdda_2v8>; + vddd-supply = <&camera_vddd_1v5>; + + port { + imx290_ep: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <445500000>; + remote-endpoint = <&csiphy0_ep>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt index 8ee7c7972ac7..10ece8108081 100644 --- a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt +++ b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt @@ -7,6 +7,9 @@ of that. These definitions are valid for both types of sensors. More detailed documentation can be found in Documentation/devicetree/bindings/media/video-interfaces.txt . +The device node should contain a "port" node which may contain one or more +endpoint nodes, in accordance with video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt . Mandatory properties -------------------- @@ -24,8 +27,6 @@ Mandatory properties Optional properties ------------------- -- nokia,nvm-size: The size of the NVM, in bytes. If the size is not given, - the NVM contents will not be read. - reset-gpios: XSHUTDOWN GPIO - flash-leds: See ../video-interfaces.txt - lens-focus: See ../video-interfaces.txt @@ -37,9 +38,7 @@ Optional properties Endpoint node mandatory properties ---------------------------------- -- clock-lanes: <0> - data-lanes: <1..n> -- remote-endpoint: A phandle to the bus receiver's endpoint node. Example @@ -48,7 +47,7 @@ Example &i2c2 { clock-frequency = <400000>; - smiapp_1: camera@10 { + camera-sensor@10 { compatible = "nokia,smia"; reg = <0x10>; reset-gpios = <&gpio3 20 0>; @@ -58,8 +57,7 @@ Example nokia,nvm-size = <512>; /* 8 * 64 */ link-frequencies = /bits/ 64 <199200000 210000000 499200000>; port { - smiapp_1_1: endpoint { - clock-lanes = <0>; + smiapp_ep: endpoint { data-lanes = <1 2>; remote-endpoint = <&csi2a_ep>; }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov2659.txt b/Documentation/devicetree/bindings/media/i2c/ov2659.txt index cabc7d827dfb..92989a619f29 100644 --- a/Documentation/devicetree/bindings/media/i2c/ov2659.txt +++ b/Documentation/devicetree/bindings/media/i2c/ov2659.txt @@ -12,6 +12,12 @@ Required Properties: - clock-names: should be "xvclk". - link-frequencies: target pixel clock frequency. +Optional Properties: +- powerdown-gpios: reference to the GPIO connected to the pwdn pin, if any. + Active high with internal pull down resistor. +- reset-gpios: reference to the GPIO connected to the resetb pin, if any. + Active low with internal pull up resistor. + For further reading on port node refer to Documentation/devicetree/bindings/media/video-interfaces.txt. @@ -27,6 +33,9 @@ Example: clocks = <&clk_ov2659 0>; clock-names = "xvclk"; + powerdown-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio6 15 GPIO_ACTIVE_LOW>; + port { ov2659_0: endpoint { remote-endpoint = <&vpfe_ep>; |
