diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iommu')
9 files changed, 467 insertions, 329 deletions
diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt b/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt deleted file mode 100644 index c9abbf3e4f68..000000000000 --- a/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt +++ /dev/null @@ -1,77 +0,0 @@ -* ARM SMMUv3 Architecture Implementation - -The SMMUv3 architecture is a significant departure from previous -revisions, replacing the MMIO register interface with in-memory command -and event queues and adding support for the ATS and PRI components of -the PCIe specification. - -** SMMUv3 required properties: - -- compatible : Should include: - - * "arm,smmu-v3" for any SMMUv3 compliant - implementation. This entry should be last in the - compatible list. - -- reg : Base address and size of the SMMU. - -- interrupts : Non-secure interrupt list describing the wired - interrupt sources corresponding to entries in - interrupt-names. If no wired interrupts are - present then this property may be omitted. - -- interrupt-names : When the interrupts property is present, should - include the following: - * "eventq" - Event Queue not empty - * "priq" - PRI Queue not empty - * "cmdq-sync" - CMD_SYNC complete - * "gerror" - Global Error activated - * "combined" - The combined interrupt is optional, - and should only be provided if the - hardware supports just a single, - combined interrupt line. - If provided, then the combined interrupt - will be used in preference to any others. - -- #iommu-cells : See the generic IOMMU binding described in - devicetree/bindings/pci/pci-iommu.txt - for details. For SMMUv3, must be 1, with each cell - describing a single stream ID. All possible stream - IDs which a device may emit must be described. - -** SMMUv3 optional properties: - -- dma-coherent : Present if DMA operations made by the SMMU (page - table walks, stream table accesses etc) are cache - coherent with the CPU. - - NOTE: this only applies to the SMMU itself, not - masters connected upstream of the SMMU. - -- msi-parent : See the generic MSI binding described in - devicetree/bindings/interrupt-controller/msi.txt - for a description of the msi-parent property. - -- hisilicon,broken-prefetch-cmd - : Avoid sending CMD_PREFETCH_* commands to the SMMU. - -- cavium,cn9900-broken-page1-regspace - : Replaces all page 1 offsets used for EVTQ_PROD/CONS, - PRIQ_PROD/CONS register access with page 0 offsets. - Set for Cavium ThunderX2 silicon that doesn't support - SMMU page1 register space. - -** Example - - smmu@2b400000 { - compatible = "arm,smmu-v3"; - reg = <0x0 0x2b400000 0x0 0x20000>; - interrupts = <GIC_SPI 74 IRQ_TYPE_EDGE_RISING>, - <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>, - <GIC_SPI 77 IRQ_TYPE_EDGE_RISING>, - <GIC_SPI 79 IRQ_TYPE_EDGE_RISING>; - interrupt-names = "eventq", "priq", "cmdq-sync", "gerror"; - dma-coherent; - #iommu-cells = <1>; - msi-parent = <&its 0xff0000>; - }; diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu-v3.yaml b/Documentation/devicetree/bindings/iommu/arm,smmu-v3.yaml new file mode 100644 index 000000000000..5951c6f98c74 --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/arm,smmu-v3.yaml @@ -0,0 +1,95 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iommu/arm,smmu-v3.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM SMMUv3 Architecture Implementation + +maintainers: + - Will Deacon <will@kernel.org> + - Robin Murphy <Robin.Murphy@arm.com> + +description: |+ + The SMMUv3 architecture is a significant departure from previous + revisions, replacing the MMIO register interface with in-memory command + and event queues and adding support for the ATS and PRI components of + the PCIe specification. + +properties: + $nodename: + pattern: "^iommu@[0-9a-f]*" + compatible: + const: arm,smmu-v3 + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 4 + + interrupt-names: + oneOf: + - const: combined + description: + The combined interrupt is optional, and should only be provided if the + hardware supports just a single, combined interrupt line. + If provided, then the combined interrupt will be used in preference to + any others. + - minItems: 2 + maxItems: 4 + items: + - const: eventq # Event Queue not empty + - const: gerror # Global Error activated + - const: priq # PRI Queue not empty + - const: cmdq-sync # CMD_SYNC complete + + '#iommu-cells': + const: 1 + + dma-coherent: + description: | + Present if page table walks made by the SMMU are cache coherent with the + CPU. + + NOTE: this only applies to the SMMU itself, not masters connected + upstream of the SMMU. + + msi-parent: true + + hisilicon,broken-prefetch-cmd: + type: boolean + description: Avoid sending CMD_PREFETCH_* commands to the SMMU. + + cavium,cn9900-broken-page1-regspace: + type: boolean + description: + Replaces all page 1 offsets used for EVTQ_PROD/CONS, PRIQ_PROD/CONS + register access with page 0 offsets. Set for Cavium ThunderX2 silicon that + doesn't support SMMU page1 register space. + +required: + - compatible + - reg + - '#iommu-cells' + +additionalProperties: false + +examples: + - |+ + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + iommu@2b400000 { + compatible = "arm,smmu-v3"; + reg = <0x2b400000 0x20000>; + interrupts = <GIC_SPI 74 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 77 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 79 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "eventq", "gerror", "priq", "cmdq-sync"; + dma-coherent; + #iommu-cells = <1>; + msi-parent = <&its 0xff0000>; + }; diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu.txt b/Documentation/devicetree/bindings/iommu/arm,smmu.txt deleted file mode 100644 index 3133f3ba7567..000000000000 --- a/Documentation/devicetree/bindings/iommu/arm,smmu.txt +++ /dev/null @@ -1,182 +0,0 @@ -* ARM System MMU Architecture Implementation - -ARM SoCs may contain an implementation of the ARM System Memory -Management Unit Architecture, which can be used to provide 1 or 2 stages -of address translation to bus masters external to the CPU. - -The SMMU may also raise interrupts in response to various fault -conditions. - -** System MMU required properties: - -- compatible : Should be one of: - - "arm,smmu-v1" - "arm,smmu-v2" - "arm,mmu-400" - "arm,mmu-401" - "arm,mmu-500" - "cavium,smmu-v2" - "qcom,smmu-v2" - - depending on the particular implementation and/or the - version of the architecture implemented. - - Qcom SoCs must contain, as below, SoC-specific compatibles - along with "qcom,smmu-v2": - "qcom,msm8996-smmu-v2", "qcom,smmu-v2", - "qcom,sdm845-smmu-v2", "qcom,smmu-v2". - - Qcom SoCs implementing "arm,mmu-500" must also include, - as below, SoC-specific compatibles: - "qcom,sdm845-smmu-500", "arm,mmu-500" - -- reg : Base address and size of the SMMU. - -- #global-interrupts : The number of global interrupts exposed by the - device. - -- interrupts : Interrupt list, with the first #global-irqs entries - corresponding to the global interrupts and any - following entries corresponding to context interrupts, - specified in order of their indexing by the SMMU. - - For SMMUv2 implementations, there must be exactly one - interrupt per context bank. In the case of a single, - combined interrupt, it must be listed multiple times. - -- #iommu-cells : See Documentation/devicetree/bindings/iommu/iommu.txt - for details. With a value of 1, each IOMMU specifier - represents a distinct stream ID emitted by that device - into the relevant SMMU. - - SMMUs with stream matching support and complex masters - may use a value of 2, where the second cell of the - IOMMU specifier represents an SMR mask to combine with - the ID in the first cell. Care must be taken to ensure - the set of matched IDs does not result in conflicts. - -** System MMU optional properties: - -- dma-coherent : Present if page table walks made by the SMMU are - cache coherent with the CPU. - - NOTE: this only applies to the SMMU itself, not - masters connected upstream of the SMMU. - -- calxeda,smmu-secure-config-access : Enable proper handling of buggy - implementations that always use secure access to - SMMU configuration registers. In this case non-secure - aliases of secure registers have to be used during - SMMU configuration. - -- stream-match-mask : For SMMUs supporting stream matching and using - #iommu-cells = <1>, specifies a mask of bits to ignore - when matching stream IDs (e.g. this may be programmed - into the SMRn.MASK field of every stream match register - used). For cases where it is desirable to ignore some - portion of every Stream ID (e.g. for certain MMU-500 - configurations given globally unique input IDs). This - property is not valid for SMMUs using stream indexing, - or using stream matching with #iommu-cells = <2>, and - may be ignored if present in such cases. - -- clock-names: List of the names of clocks input to the device. The - required list depends on particular implementation and - is as follows: - - for "qcom,smmu-v2": - - "bus": clock required for downstream bus access and - for the smmu ptw, - - "iface": clock required to access smmu's registers - through the TCU's programming interface. - - unspecified for other implementations. - -- clocks: Specifiers for all clocks listed in the clock-names property, - as per generic clock bindings. - -- power-domains: Specifiers for power domains required to be powered on for - the SMMU to operate, as per generic power domain bindings. - -** Deprecated properties: - -- mmu-masters (deprecated in favour of the generic "iommus" binding) : - A list of phandles to device nodes representing bus - masters for which the SMMU can provide a translation - and their corresponding Stream IDs. Each device node - linked from this list must have a "#stream-id-cells" - property, indicating the number of Stream ID - arguments associated with its phandle. - -** Examples: - - /* SMMU with stream matching or stream indexing */ - smmu1: iommu { - compatible = "arm,smmu-v1"; - reg = <0xba5e0000 0x10000>; - #global-interrupts = <2>; - interrupts = <0 32 4>, - <0 33 4>, - <0 34 4>, /* This is the first context interrupt */ - <0 35 4>, - <0 36 4>, - <0 37 4>; - #iommu-cells = <1>; - }; - - /* device with two stream IDs, 0 and 7 */ - master1 { - iommus = <&smmu1 0>, - <&smmu1 7>; - }; - - - /* SMMU with stream matching */ - smmu2: iommu { - ... - #iommu-cells = <2>; - }; - - /* device with stream IDs 0 and 7 */ - master2 { - iommus = <&smmu2 0 0>, - <&smmu2 7 0>; - }; - - /* device with stream IDs 1, 17, 33 and 49 */ - master3 { - iommus = <&smmu2 1 0x30>; - }; - - - /* ARM MMU-500 with 10-bit stream ID input configuration */ - smmu3: iommu { - compatible = "arm,mmu-500", "arm,smmu-v2"; - ... - #iommu-cells = <1>; - /* always ignore appended 5-bit TBU number */ - stream-match-mask = 0x7c00; - }; - - bus { - /* bus whose child devices emit one unique 10-bit stream - ID each, but may master through multiple SMMU TBUs */ - iommu-map = <0 &smmu3 0 0x400>; - ... - }; - - /* Qcom's arm,smmu-v2 implementation */ - smmu4: iommu@d00000 { - compatible = "qcom,msm8996-smmu-v2", "qcom,smmu-v2"; - reg = <0xd00000 0x10000>; - - #global-interrupts = <1>; - interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>; - #iommu-cells = <1>; - power-domains = <&mmcc MDSS_GDSC>; - - clocks = <&mmcc SMMU_MDP_AXI_CLK>, - <&mmcc SMMU_MDP_AHB_CLK>; - clock-names = "bus", "iface"; - }; diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu.yaml b/Documentation/devicetree/bindings/iommu/arm,smmu.yaml new file mode 100644 index 000000000000..6515dbe47508 --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/arm,smmu.yaml @@ -0,0 +1,230 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iommu/arm,smmu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM System MMU Architecture Implementation + +maintainers: + - Will Deacon <will@kernel.org> + - Robin Murphy <Robin.Murphy@arm.com> + +description: |+ + ARM SoCs may contain an implementation of the ARM System Memory + Management Unit Architecture, which can be used to provide 1 or 2 stages + of address translation to bus masters external to the CPU. + + The SMMU may also raise interrupts in response to various fault + conditions. + +properties: + $nodename: + pattern: "^iommu@[0-9a-f]*" + compatible: + oneOf: + - description: Qcom SoCs implementing "arm,smmu-v2" + items: + - enum: + - qcom,msm8996-smmu-v2 + - qcom,msm8998-smmu-v2 + - qcom,sdm845-smmu-v2 + - const: qcom,smmu-v2 + + - description: Qcom SoCs implementing "arm,mmu-500" + items: + - enum: + - qcom,sc7180-smmu-500 + - qcom,sdm845-smmu-500 + - const: arm,mmu-500 + - items: + - const: arm,mmu-500 + - const: arm,smmu-v2 + - items: + - const: arm,mmu-401 + - const: arm,smmu-v1 + - enum: + - arm,smmu-v1 + - arm,smmu-v2 + - arm,mmu-400 + - arm,mmu-401 + - arm,mmu-500 + - cavium,smmu-v2 + + reg: + maxItems: 1 + + '#global-interrupts': + description: The number of global interrupts exposed by the device. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 260 # 2 secure, 2 non-secure, and up to 256 perf counters + + '#iommu-cells': + enum: [ 1, 2 ] + description: | + See Documentation/devicetree/bindings/iommu/iommu.txt for details. With a + value of 1, each IOMMU specifier represents a distinct stream ID emitted + by that device into the relevant SMMU. + + SMMUs with stream matching support and complex masters may use a value of + 2, where the second cell of the IOMMU specifier represents an SMR mask to + combine with the ID in the first cell. Care must be taken to ensure the + set of matched IDs does not result in conflicts. + + interrupts: + minItems: 1 + maxItems: 388 # 260 plus 128 contexts + description: | + Interrupt list, with the first #global-interrupts entries corresponding to + the global interrupts and any following entries corresponding to context + interrupts, specified in order of their indexing by the SMMU. + + For SMMUv2 implementations, there must be exactly one interrupt per + context bank. In the case of a single, combined interrupt, it must be + listed multiple times. + + dma-coherent: + description: | + Present if page table walks made by the SMMU are cache coherent with the + CPU. + + NOTE: this only applies to the SMMU itself, not masters connected + upstream of the SMMU. + + calxeda,smmu-secure-config-access: + type: boolean + description: + Enable proper handling of buggy implementations that always use secure + access to SMMU configuration registers. In this case non-secure aliases of + secure registers have to be used during SMMU configuration. + + stream-match-mask: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + For SMMUs supporting stream matching and using #iommu-cells = <1>, + specifies a mask of bits to ignore when matching stream IDs (e.g. this may + be programmed into the SMRn.MASK field of every stream match register + used). For cases where it is desirable to ignore some portion of every + Stream ID (e.g. for certain MMU-500 configurations given globally unique + input IDs). This property is not valid for SMMUs using stream indexing, or + using stream matching with #iommu-cells = <2>, and may be ignored if + present in such cases. + + clock-names: + items: + - const: bus + - const: iface + + clocks: + items: + - description: bus clock required for downstream bus access and for the + smmu ptw + - description: interface clock required to access smmu's registers + through the TCU's programming interface. + + power-domains: + maxItems: 1 + +required: + - compatible + - reg + - '#global-interrupts' + - '#iommu-cells' + - interrupts + +additionalProperties: false + +examples: + - |+ + /* SMMU with stream matching or stream indexing */ + smmu1: iommu@ba5e0000 { + compatible = "arm,smmu-v1"; + reg = <0xba5e0000 0x10000>; + #global-interrupts = <2>; + interrupts = <0 32 4>, + <0 33 4>, + <0 34 4>, /* This is the first context interrupt */ + <0 35 4>, + <0 36 4>, + <0 37 4>; + #iommu-cells = <1>; + }; + + /* device with two stream IDs, 0 and 7 */ + master1 { + iommus = <&smmu1 0>, + <&smmu1 7>; + }; + + + /* SMMU with stream matching */ + smmu2: iommu@ba5f0000 { + compatible = "arm,smmu-v1"; + reg = <0xba5f0000 0x10000>; + #global-interrupts = <2>; + interrupts = <0 38 4>, + <0 39 4>, + <0 40 4>, /* This is the first context interrupt */ + <0 41 4>, + <0 42 4>, + <0 43 4>; + #iommu-cells = <2>; + }; + + /* device with stream IDs 0 and 7 */ + master2 { + iommus = <&smmu2 0 0>, + <&smmu2 7 0>; + }; + + /* device with stream IDs 1, 17, 33 and 49 */ + master3 { + iommus = <&smmu2 1 0x30>; + }; + + + /* ARM MMU-500 with 10-bit stream ID input configuration */ + smmu3: iommu@ba600000 { + compatible = "arm,mmu-500", "arm,smmu-v2"; + reg = <0xba600000 0x10000>; + #global-interrupts = <2>; + interrupts = <0 44 4>, + <0 45 4>, + <0 46 4>, /* This is the first context interrupt */ + <0 47 4>, + <0 48 4>, + <0 49 4>; + #iommu-cells = <1>; + /* always ignore appended 5-bit TBU number */ + stream-match-mask = <0x7c00>; + }; + + bus { + /* bus whose child devices emit one unique 10-bit stream + ID each, but may master through multiple SMMU TBUs */ + iommu-map = <0 &smmu3 0 0x400>; + + + }; + + - |+ + /* Qcom's arm,smmu-v2 implementation */ + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + smmu4: iommu@d00000 { + compatible = "qcom,msm8996-smmu-v2", "qcom,smmu-v2"; + reg = <0xd00000 0x10000>; + + #global-interrupts = <1>; + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + power-domains = <&mmcc 0>; + + clocks = <&mmcc 123>, + <&mmcc 124>; + clock-names = "bus", "iface"; + }; diff --git a/Documentation/devicetree/bindings/iommu/iommu.txt b/Documentation/devicetree/bindings/iommu/iommu.txt index 5a8b4624defc..3c36334e4f94 100644 --- a/Documentation/devicetree/bindings/iommu/iommu.txt +++ b/Documentation/devicetree/bindings/iommu/iommu.txt @@ -86,6 +86,12 @@ have a means to turn off translation. But it is invalid in such cases to disable the IOMMU's device tree node in the first place because it would prevent any driver from properly setting up the translations. +Optional properties: +-------------------- +- pasid-num-bits: Some masters support multiple address spaces for DMA, by + tagging DMA transactions with an address space identifier. By default, + this is 0, which means that the device only has one address space. + Notes: ====== diff --git a/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt index 6922db598def..ce59a505f5a4 100644 --- a/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt +++ b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt @@ -11,10 +11,23 @@ ARM Short-Descriptor translation table format for address translation. | m4u (Multimedia Memory Management Unit) | + +--------+ + | | + gals0-rx gals1-rx (Global Async Local Sync rx) + | | + | | + gals0-tx gals1-tx (Global Async Local Sync tx) + | | Some SoCs may have GALS. + +--------+ + | SMI Common(Smart Multimedia Interface Common) | +----------------+------- | | + | gals-rx There may be GALS in some larbs. + | | + | | + | gals-tx | | SMI larb0 SMI larb1 ... SoCs have several SMI local arbiter(larb). (display) (vdec) @@ -36,6 +49,10 @@ each local arbiter. like display, video decode, and camera. And there are different ports in each larb. Take a example, There are many ports like MC, PP, VLD in the video decode local arbiter, all these ports are according to the video HW. + In some SoCs, there may be a GALS(Global Async Local Sync) module between +smi-common and m4u, and additional GALS module between smi-larb and +smi-common. GALS can been seen as a "asynchronous fifo" which could help +synchronize for the modules in different clock frequency. Required properties: - compatible : must be one of the following string: @@ -44,18 +61,25 @@ Required properties: "mediatek,mt7623-m4u", "mediatek,mt2701-m4u" for mt7623 which uses generation one m4u HW. "mediatek,mt8173-m4u" for mt8173 which uses generation two m4u HW. + "mediatek,mt8183-m4u" for mt8183 which uses generation two m4u HW. - reg : m4u register base and size. - interrupts : the interrupt of m4u. - clocks : must contain one entry for each clock-names. -- clock-names : must be "bclk", It is the block clock of m4u. +- clock-names : Only 1 optional clock: + - "bclk": the block clock of m4u. + Here is the list which require this "bclk": + - mt2701, mt2712, mt7623 and mt8173. + Note that m4u use the EMI clock which always has been enabled before kernel + if there is no this "bclk". - mediatek,larbs : List of phandle to the local arbiters in the current Socs. Refer to bindings/memory-controllers/mediatek,smi-larb.txt. It must sort according to the local arbiter index, like larb0, larb1, larb2... - iommu-cells : must be 1. This is the mtk_m4u_id according to the HW. Specifies the mtk_m4u_id as defined in dt-binding/memory/mt2701-larb-port.h for mt2701, mt7623 - dt-binding/memory/mt2712-larb-port.h for mt2712, and - dt-binding/memory/mt8173-larb-port.h for mt8173. + dt-binding/memory/mt2712-larb-port.h for mt2712, + dt-binding/memory/mt8173-larb-port.h for mt8173, and + dt-binding/memory/mt8183-larb-port.h for mt8183. Example: iommu: iommu@10205000 { diff --git a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt index b6bfbec3a849..020d6f226efb 100644 --- a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt +++ b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt @@ -15,6 +15,7 @@ Required Properties: - "renesas,ipmmu-r8a7744" for the R8A7744 (RZ/G1N) IPMMU. - "renesas,ipmmu-r8a7745" for the R8A7745 (RZ/G1E) IPMMU. - "renesas,ipmmu-r8a774a1" for the R8A774A1 (RZ/G2M) IPMMU. + - "renesas,ipmmu-r8a774b1" for the R8A774B1 (RZ/G2N) IPMMU. - "renesas,ipmmu-r8a774c0" for the R8A774C0 (RZ/G2E) IPMMU. - "renesas,ipmmu-r8a7790" for the R8A7790 (R-Car H2) IPMMU. - "renesas,ipmmu-r8a7791" for the R8A7791 (R-Car M2-W) IPMMU. diff --git a/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt b/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt deleted file mode 100644 index 525ec82615a6..000000000000 --- a/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt +++ /dev/null @@ -1,67 +0,0 @@ -Samsung Exynos IOMMU H/W, System MMU (System Memory Management Unit) - -Samsung's Exynos architecture contains System MMUs that enables scattered -physical memory chunks visible as a contiguous region to DMA-capable peripheral -devices like MFC, FIMC, FIMD, GScaler, FIMC-IS and so forth. - -System MMU is an IOMMU and supports identical translation table format to -ARMv7 translation tables with minimum set of page properties including access -permissions, shareability and security protection. In addition, System MMU has -another capabilities like L2 TLB or block-fetch buffers to minimize translation -latency. - -System MMUs are in many to one relation with peripheral devices, i.e. single -peripheral device might have multiple System MMUs (usually one for each bus -master), but one System MMU can handle transactions from only one peripheral -device. The relation between a System MMU and the peripheral device needs to be -defined in device node of the peripheral device. - -MFC in all Exynos SoCs and FIMD, M2M Scalers and G2D in Exynos5420 has 2 System -MMUs. -* MFC has one System MMU on its left and right bus. -* FIMD in Exynos5420 has one System MMU for window 0 and 4, the other system MMU - for window 1, 2 and 3. -* M2M Scalers and G2D in Exynos5420 has one System MMU on the read channel and - the other System MMU on the write channel. - -For information on assigning System MMU controller to its peripheral devices, -see generic IOMMU bindings. - -Required properties: -- compatible: Should be "samsung,exynos-sysmmu" -- reg: A tuple of base address and size of System MMU registers. -- #iommu-cells: Should be <0>. -- interrupts: An interrupt specifier for interrupt signal of System MMU, - according to the format defined by a particular interrupt - controller. -- clock-names: Should be "sysmmu" or a pair of "aclk" and "pclk" to gate - SYSMMU core clocks. - Optional "master" if the clock to the System MMU is gated by - another gate clock other core (usually main gate clock - of peripheral device this SYSMMU belongs to). -- clocks: Phandles for respective clocks described by clock-names. -- power-domains: Required if the System MMU is needed to gate its power. - Please refer to the following document: - Documentation/devicetree/bindings/power/pd-samsung.txt - -Examples: - gsc_0: gsc@13e00000 { - compatible = "samsung,exynos5-gsc"; - reg = <0x13e00000 0x1000>; - interrupts = <0 85 0>; - power-domains = <&pd_gsc>; - clocks = <&clock CLK_GSCL0>; - clock-names = "gscl"; - iommus = <&sysmmu_gsc0>; - }; - - sysmmu_gsc0: sysmmu@13e80000 { - compatible = "samsung,exynos-sysmmu"; - reg = <0x13E80000 0x1000>; - interrupt-parent = <&combiner>; - interrupts = <2 0>; - clock-names = "sysmmu", "master"; - clocks = <&clock CLK_SMMU_GSCL0>, <&clock CLK_GSCL0>; - power-domains = <&pd_gsc>; - #iommu-cells = <0>; - }; diff --git a/Documentation/devicetree/bindings/iommu/samsung,sysmmu.yaml b/Documentation/devicetree/bindings/iommu/samsung,sysmmu.yaml new file mode 100644 index 000000000000..7cdd3aaa2ba4 --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/samsung,sysmmu.yaml @@ -0,0 +1,108 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iommu/samsung,sysmmu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung Exynos IOMMU H/W, System MMU (System Memory Management Unit) + +maintainers: + - Marek Szyprowski <m.szyprowski@samsung.com> + +description: |+ + Samsung's Exynos architecture contains System MMUs that enables scattered + physical memory chunks visible as a contiguous region to DMA-capable peripheral + devices like MFC, FIMC, FIMD, GScaler, FIMC-IS and so forth. + + System MMU is an IOMMU and supports identical translation table format to + ARMv7 translation tables with minimum set of page properties including access + permissions, shareability and security protection. In addition, System MMU has + another capabilities like L2 TLB or block-fetch buffers to minimize translation + latency. + + System MMUs are in many to one relation with peripheral devices, i.e. single + peripheral device might have multiple System MMUs (usually one for each bus + master), but one System MMU can handle transactions from only one peripheral + device. The relation between a System MMU and the peripheral device needs to be + defined in device node of the peripheral device. + + MFC in all Exynos SoCs and FIMD, M2M Scalers and G2D in Exynos5420 has 2 System + MMUs. + * MFC has one System MMU on its left and right bus. + * FIMD in Exynos5420 has one System MMU for window 0 and 4, the other system MMU + for window 1, 2 and 3. + * M2M Scalers and G2D in Exynos5420 has one System MMU on the read channel and + the other System MMU on the write channel. + + For information on assigning System MMU controller to its peripheral devices, + see generic IOMMU bindings. + +properties: + compatible: + const: samsung,exynos-sysmmu + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + oneOf: + - items: + - const: sysmmu + - items: + - const: sysmmu + - const: master + - items: + - const: aclk + - const: pclk + + "#iommu-cells": + const: 0 + + power-domains: + description: | + Required if the System MMU is needed to gate its power. + Please refer to the following document: + Documentation/devicetree/bindings/power/pd-samsung.yaml + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - "#iommu-cells" + +examples: + - | + #include <dt-bindings/clock/exynos5250.h> + + gsc_0: scaler@13e00000 { + compatible = "samsung,exynos5-gsc"; + reg = <0x13e00000 0x1000>; + interrupts = <0 85 0>; + power-domains = <&pd_gsc>; + clocks = <&clock CLK_GSCL0>; + clock-names = "gscl"; + iommus = <&sysmmu_gsc0>; + }; + + sysmmu_gsc0: iommu@13e80000 { + compatible = "samsung,exynos-sysmmu"; + reg = <0x13E80000 0x1000>; + interrupt-parent = <&combiner>; + interrupts = <2 0>; + clock-names = "sysmmu", "master"; + clocks = <&clock CLK_SMMU_GSCL0>, + <&clock CLK_GSCL0>; + power-domains = <&pd_gsc>; + #iommu-cells = <0>; + }; + |
