diff options
Diffstat (limited to 'Documentation/admin-guide/perf')
| -rw-r--r-- | Documentation/admin-guide/perf/imx-ddr.rst | 70 | ||||
| -rw-r--r-- | Documentation/admin-guide/perf/index.rst | 1 | ||||
| -rw-r--r-- | Documentation/admin-guide/perf/thunderx2-pmu.rst | 20 |
3 files changed, 82 insertions, 9 deletions
diff --git a/Documentation/admin-guide/perf/imx-ddr.rst b/Documentation/admin-guide/perf/imx-ddr.rst new file mode 100644 index 000000000000..3726a10a03ba --- /dev/null +++ b/Documentation/admin-guide/perf/imx-ddr.rst @@ -0,0 +1,70 @@ +===================================================== +Freescale i.MX8 DDR Performance Monitoring Unit (PMU) +===================================================== + +There are no performance counters inside the DRAM controller, so performance +signals are brought out to the edge of the controller where a set of 4 x 32 bit +counters is implemented. This is controlled by the CSV modes programed in counter +control register which causes a large number of PERF signals to be generated. + +Selection of the value for each counter is done via the config registers. There +is one register for each counter. Counter 0 is special in that it always counts +“time” and when expired causes a lock on itself and the other counters and an +interrupt is raised. If any other counter overflows, it continues counting, and +no interrupt is raised. + +The "format" directory describes format of the config (event ID) and config1 +(AXI filtering) fields of the perf_event_attr structure, see /sys/bus/event_source/ +devices/imx8_ddr0/format/. The "events" directory describes the events types +hardware supported that can be used with perf tool, see /sys/bus/event_source/ +devices/imx8_ddr0/events/. The "caps" directory describes filter features implemented +in DDR PMU, see /sys/bus/events_source/devices/imx8_ddr0/caps/. + + .. code-block:: bash + + perf stat -a -e imx8_ddr0/cycles/ cmd + perf stat -a -e imx8_ddr0/read/,imx8_ddr0/write/ cmd + +AXI filtering is only used by CSV modes 0x41 (axid-read) and 0x42 (axid-write) +to count reading or writing matches filter setting. Filter setting is various +from different DRAM controller implementations, which is distinguished by quirks +in the driver. You also can dump info from userspace, filter in "caps" directory +indicates whether PMU supports AXI ID filter or not; enhanced_filter indicates +whether PMU supports enhanced AXI ID filter or not. Value 0 for un-supported, and +value 1 for supported. + +* With DDR_CAP_AXI_ID_FILTER quirk(filter: 1, enhanced_filter: 0). + Filter is defined with two configuration parts: + --AXI_ID defines AxID matching value. + --AXI_MASKING defines which bits of AxID are meaningful for the matching. + + - 0: corresponding bit is masked. + - 1: corresponding bit is not masked, i.e. used to do the matching. + + AXI_ID and AXI_MASKING are mapped on DPCR1 register in performance counter. + When non-masked bits are matching corresponding AXI_ID bits then counter is + incremented. Perf counter is incremented if + AxID && AXI_MASKING == AXI_ID && AXI_MASKING + + This filter doesn't support filter different AXI ID for axid-read and axid-write + event at the same time as this filter is shared between counters. + + .. code-block:: bash + + perf stat -a -e imx8_ddr0/axid-read,axi_mask=0xMMMM,axi_id=0xDDDD/ cmd + perf stat -a -e imx8_ddr0/axid-write,axi_mask=0xMMMM,axi_id=0xDDDD/ cmd + + .. note:: + + axi_mask is inverted in userspace(i.e. set bits are bits to mask), and + it will be reverted in driver automatically. so that the user can just specify + axi_id to monitor a specific id, rather than having to specify axi_mask. + + .. code-block:: bash + + perf stat -a -e imx8_ddr0/axid-read,axi_id=0x12/ cmd, which will monitor ARID=0x12 + +* With DDR_CAP_AXI_ID_FILTER_ENHANCED quirk(filter: 1, enhanced_filter: 1). + This is an extension to the DDR_CAP_AXI_ID_FILTER quirk which permits + counting the number of bytes (as opposed to the number of bursts) from DDR + read and write transactions concurrently with another set of data counters. diff --git a/Documentation/admin-guide/perf/index.rst b/Documentation/admin-guide/perf/index.rst index ee4bfd2a740f..47c99f40cc16 100644 --- a/Documentation/admin-guide/perf/index.rst +++ b/Documentation/admin-guide/perf/index.rst @@ -8,6 +8,7 @@ Performance monitor support :maxdepth: 1 hisi-pmu + imx-ddr qcom_l2_pmu qcom_l3_pmu arm-ccn diff --git a/Documentation/admin-guide/perf/thunderx2-pmu.rst b/Documentation/admin-guide/perf/thunderx2-pmu.rst index 08e33675853a..01f158238ae1 100644 --- a/Documentation/admin-guide/perf/thunderx2-pmu.rst +++ b/Documentation/admin-guide/perf/thunderx2-pmu.rst @@ -3,24 +3,26 @@ Cavium ThunderX2 SoC Performance Monitoring Unit (PMU UNCORE) ============================================================= The ThunderX2 SoC PMU consists of independent, system-wide, per-socket -PMUs such as the Level 3 Cache (L3C) and DDR4 Memory Controller (DMC). +PMUs such as the Level 3 Cache (L3C), DDR4 Memory Controller (DMC) and +Cavium Coherent Processor Interconnect (CCPI2). The DMC has 8 interleaved channels and the L3C has 16 interleaved tiles. Events are counted for the default channel (i.e. channel 0) and prorated to the total number of channels/tiles. -The DMC and L3C support up to 4 counters. Counters are independently -programmable and can be started and stopped individually. Each counter -can be set to a different event. Counters are 32-bit and do not support -an overflow interrupt; they are read every 2 seconds. +The DMC and L3C support up to 4 counters, while the CCPI2 supports up to 8 +counters. Counters are independently programmable to different events and +can be started and stopped individually. None of the counters support an +overflow interrupt. DMC and L3C counters are 32-bit and read every 2 seconds. +The CCPI2 counters are 64-bit and assumed not to overflow in normal operation. PMU UNCORE (perf) driver: The thunderx2_pmu driver registers per-socket perf PMUs for the DMC and -L3C devices. Each PMU can be used to count up to 4 events -simultaneously. The PMUs provide a description of their available events -and configuration options under sysfs, see -/sys/devices/uncore_<l3c_S/dmc_S/>; S is the socket id. +L3C devices. Each PMU can be used to count up to 4 (DMC/L3C) or up to 8 +(CCPI2) events simultaneously. The PMUs provide a description of their +available events and configuration options under sysfs, see +/sys/devices/uncore_<l3c_S/dmc_S/ccpi2_S/>; S is the socket id. The driver does not support sampling, therefore "perf record" will not work. Per-task perf sessions are also not supported. |
