diff options
| author | Yuval Mintz <Yuval.Mintz@qlogic.com> | 2015-04-22 12:47:32 +0300 |
|---|---|---|
| committer | David S. Miller <davem@davemloft.net> | 2015-04-22 14:23:31 -0400 |
| commit | 909d9faae2a447110aa061070145297fffe129cb (patch) | |
| tree | 57929e27c0d5634ca09405c24b8357aa264b9723 /drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c | |
| parent | a2c3935aaa8fe99dbddb13ff244ecec7c324ec8b (diff) | |
| download | talos-op-linux-909d9faae2a447110aa061070145297fffe129cb.tar.gz talos-op-linux-909d9faae2a447110aa061070145297fffe129cb.zip | |
bnx2x: Prevent inner-reload while VFs exist
On some feature changes, driver employes an inner-reload flow where it
resets the function and re-configures it with the new required set of
parameters.
Such a flow proves fatal to any VF since those were not intended to be used
while HW is being reset underneath, causing them [at best] to lose all
connectivity.
This changes driver behavior to fail all configuration changes [e.g., mtu
change] requested of the driver in case VFs are active.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Diffstat (limited to 'drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c')
| -rw-r--r-- | drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c | 17 |
1 files changed, 17 insertions, 0 deletions
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c index e3d853cab7c9..48ed005ba73f 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c @@ -1843,6 +1843,12 @@ static int bnx2x_set_ringparam(struct net_device *dev, "set ring params command parameters: rx_pending = %d, tx_pending = %d\n", ering->rx_pending, ering->tx_pending); + if (pci_num_vf(bp->pdev)) { + DP(BNX2X_MSG_IOV, + "VFs are enabled, can not change ring parameters\n"); + return -EPERM; + } + if (bp->recovery_state != BNX2X_RECOVERY_DONE) { DP(BNX2X_MSG_ETHTOOL, "Handling parity error recovery. Try again later\n"); @@ -2899,6 +2905,12 @@ static void bnx2x_self_test(struct net_device *dev, u8 is_serdes, link_up; int rc, cnt = 0; + if (pci_num_vf(bp->pdev)) { + DP(BNX2X_MSG_IOV, + "VFs are enabled, can not perform self test\n"); + return; + } + if (bp->recovery_state != BNX2X_RECOVERY_DONE) { netdev_err(bp->dev, "Handling parity error recovery. Try again later\n"); @@ -3468,6 +3480,11 @@ static int bnx2x_set_channels(struct net_device *dev, channels->rx_count, channels->tx_count, channels->other_count, channels->combined_count); + if (pci_num_vf(bp->pdev)) { + DP(BNX2X_MSG_IOV, "VFs are enabled, can not set channels\n"); + return -EPERM; + } + /* We don't support separate rx / tx channels. * We don't allow setting 'other' channels. */ |
