diff options
| author | Martin Blumenstingl <martin.blumenstingl@googlemail.com> | 2019-03-28 21:47:21 +0100 |
|---|---|---|
| committer | Kevin Hilman <khilman@baylibre.com> | 2019-03-29 13:59:02 -0700 |
| commit | 07f9da2900674e8e7b15b090b878d8defe223277 (patch) | |
| tree | ff13ac92c833508f5046553c6af738870ddc3356 /arch/arm | |
| parent | f1975b982a2917f4fadd6af96fd1671e5dc57095 (diff) | |
| download | talos-op-linux-07f9da2900674e8e7b15b090b878d8defe223277.tar.gz talos-op-linux-07f9da2900674e8e7b15b090b878d8defe223277.zip | |
ARM: dts: meson8b: odroidc1: add the GPIO line names
This adds the GPIO line names from the schematics to get them displayed
in the debugfs output of each GPIO controller.
The schematics from Odroid-C1+ PCB revision 0.4 20150615 are used as
referenced.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Diffstat (limited to 'arch/arm')
| -rw-r--r-- | arch/arm/boot/dts/meson8b-odroidc1.dts | 52 |
1 files changed, 52 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts index 3b0e0f8fbc23..0157646e3a89 100644 --- a/arch/arm/boot/dts/meson8b-odroidc1.dts +++ b/arch/arm/boot/dts/meson8b-odroidc1.dts @@ -234,7 +234,59 @@ }; }; +&gpio { + gpio-line-names = /* Bank GPIOX */ + "J2 Header Pin 35", "J2 Header Pin 36", + "J2 Header Pin 32", "J2 Header Pin 31", + "J2 Header Pin 29", "J2 Header Pin 18", + "J2 Header Pin 22", "J2 Header Pin 16", + "J2 Header Pin 23", "J2 Header Pin 21", + "J2 Header Pin 19", "J2 Header Pin 33", + "J2 Header Pin 8", "J2 Header Pin 10", + "J2 Header Pin 15", "J2 Header Pin 13", + "J2 Header Pin 24", "J2 Header Pin 26", + /* Bank GPIOY */ + "Revision (upper)", "Revision (lower)", + "J2 Header Pin 7", "", "J2 Header Pin 12", + "J2 Header Pin 11", "", "", "", + "TFLASH_VDD_EN", "", "", + /* Bank GPIODV */ + "VCCK_PWM (PWM_C)", "I2CA_SDA", "I2CA_SCL", + "I2CB_SDA", "I2CB_SCL", "VDDEE_PWM (PWM_D)", + "", + /* Bank GPIOH */ + "HDMI_HPD", "HDMI_I2C_SDA", "HDMI_I2C_SCL", + "ETH_PHY_INTR", "ETH_PHY_NRST", "ETH_TXD1", + "ETH_TXD0", "ETH_TXD3", "ETH_TXD2", + "ETH_RGMII_TX_CLK", + /* Bank CARD */ + "SD_DATA1 (SDB_D1)", "SD_DATA0 (SDB_D0)", + "SD_CLK", "SD_CMD", "SD_DATA3 (SDB_D3)", + "SD_DATA2 (SDB_D2)", "SD_CDN (SD_DET_N)", + /* Bank BOOT */ + "SDC_D0 (EMMC)", "SDC_D1 (EMMC)", + "SDC_D2 (EMMC)", "SDC_D3 (EMMC)", + "SDC_D4 (EMMC)", "SDC_D5 (EMMC)", + "SDC_D6 (EMMC)", "SDC_D7 (EMMC)", + "SDC_CLK (EMMC)", "SDC_RSTn (EMMC)", + "SDC_CMD (EMMC)", "BOOT_SEL", "", "", "", + "", "", "", "", + /* Bank DIF */ + "ETH_RXD1", "ETH_RXD0", "ETH_RX_DV", + "RGMII_RX_CLK", "ETH_RXD3", "ETH_RXD2", + "ETH_TXEN", "ETH_PHY_REF_CLK_25MOUT", + "ETH_MDC", "ETH_MDIO"; +}; + &gpio_ao { + gpio-line-names = "UART TX", "UART RX", "", + "TF_3V3N_1V8_EN", "USB_HUB_RST_N", + "USB_OTG_PWREN", "J7 Header Pin 2", + "IR_IN", "J7 Header Pin 4", + "J7 Header Pin 6", "J7 Header Pin 5", + "J7 Header Pin 7", "HDMI_CEC", + "SYS_LED", "", ""; + /* * WARNING: The USB Hub on the Odroid-C1/C1+ needs a reset signal * to be turned high in order to be detected by the USB Controller. |
