ARM: kirkwood: fdt: facilitate new boards during fdt migration

Move all dreamplug-specific code out of board-dt.c and into
board-dreamplug.c.  This way new boards that are added during the
conversion to fdt don't clutter up board-dt.c.

Signed-off-by: Jason Cooper <jason@lakedaemon.net>

1 files changed, 1 insertions, 132 deletions

diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c
index 9bd35ac730b3..975ad0148652 100644
--- a/arch/arm/mach-kirkwood/board-dt.c
+++ b/arch/arm/mach-kirkwood/board-dt.c
@@ -3,7 +3,7 @@
  *
  * arch/arm/mach-kirkwood/board-dt.c
  *
- * Marvell DreamPlug Reference Board Setup
+ * Flattened Device Tree board initialization
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2.  This program is licensed "as is" without any
@@ -12,149 +12,18 @@
 
 #include <linux/kernel.h>
 #include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/partitions.h>
-#include <linux/ata_platform.h>
-#include <linux/mv643xx_eth.h>
 #include <linux/of.h>
-#include <linux/of_address.h>
-#include <linux/of_fdt.h>
-#include <linux/of_irq.h>
 #include <linux/of_platform.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <linux/mtd/physmap.h>
-#include <linux/spi/flash.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/orion_spi.h>
-#include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
-#include <mach/kirkwood.h>
 #include <mach/bridge-regs.h>
-#include <plat/mvsdio.h>
 #include "common.h"
-#include "mpp.h"
 
 static struct of_device_id kirkwood_dt_match_table[] __initdata = {
 	{ .compatible = "simple-bus", },
 	{ }
 };
 
-struct mtd_partition dreamplug_partitions[] = {
-	{
-		.name	= "u-boot",
-		.size	= SZ_512K,
-		.offset = 0,
-	},
-	{
-		.name	= "u-boot env",
-		.size	= SZ_64K,
-		.offset = SZ_512K + SZ_512K,
-	},
-	{
-		.name	= "dtb",
-		.size	= SZ_64K,
-		.offset = SZ_512K + SZ_512K + SZ_512K,
-	},
-};
-
-static const struct flash_platform_data dreamplug_spi_slave_data = {
-	.type		= "mx25l1606e",
-	.name		= "spi_flash",
-	.parts		= dreamplug_partitions,
-	.nr_parts	= ARRAY_SIZE(dreamplug_partitions),
-};
-
-static struct spi_board_info __initdata dreamplug_spi_slave_info[] = {
-	{
-		.modalias	= "m25p80",
-		.platform_data	= &dreamplug_spi_slave_data,
-		.irq		= -1,
-		.max_speed_hz	= 50000000,
-		.bus_num	= 0,
-		.chip_select	= 0,
-	},
-};
-
-static struct mv643xx_eth_platform_data dreamplug_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-static struct mv643xx_eth_platform_data dreamplug_ge01_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(1),
-};
-
-static struct mv_sata_platform_data dreamplug_sata_data = {
-	.n_ports	= 1,
-};
-
-static struct mvsdio_platform_data dreamplug_mvsdio_data = {
-	/* unfortunately the CD signal has not been connected */
-};
-
-static struct gpio_led dreamplug_led_pins[] = {
-	{
-		.name			= "dreamplug:blue:bluetooth",
-		.gpio			= 47,
-		.active_low		= 1,
-	},
-	{
-		.name			= "dreamplug:green:wifi",
-		.gpio			= 48,
-		.active_low		= 1,
-	},
-	{
-		.name			= "dreamplug:green:wifi_ap",
-		.gpio			= 49,
-		.active_low		= 1,
-	},
-};
-
-static struct gpio_led_platform_data dreamplug_led_data = {
-	.leds		= dreamplug_led_pins,
-	.num_leds	= ARRAY_SIZE(dreamplug_led_pins),
-};
-
-static struct platform_device dreamplug_leds = {
-	.name	= "leds-gpio",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &dreamplug_led_data,
-	}
-};
-
-static unsigned int dreamplug_mpp_config[] __initdata = {
-	MPP0_SPI_SCn,
-	MPP1_SPI_MOSI,
-	MPP2_SPI_SCK,
-	MPP3_SPI_MISO,
-	MPP47_GPIO,	/* Bluetooth LED */
-	MPP48_GPIO,	/* Wifi LED */
-	MPP49_GPIO,	/* Wifi AP LED */
-	0
-};
-
-static void __init dreamplug_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_mpp_conf(dreamplug_mpp_config);
-
-	spi_register_board_info(dreamplug_spi_slave_info,
-				ARRAY_SIZE(dreamplug_spi_slave_info));
-	kirkwood_spi_init();
-
-	kirkwood_ehci_init();
-	kirkwood_ge00_init(&dreamplug_ge00_data);
-	kirkwood_ge01_init(&dreamplug_ge01_data);
-	kirkwood_sata_init(&dreamplug_sata_data);
-	kirkwood_sdio_init(&dreamplug_mvsdio_data);
-
-	platform_device_register(&dreamplug_leds);
-}
-
 static void __init kirkwood_dt_init(void)
 {
 	pr_info("Kirkwood: %s, TCLK=%d.\n", kirkwood_id(), kirkwood_tclk);