ARM: dts: sun8i: Add BananaPI M2-Magic DTS

The Bananapi M2-Magic is a board with an A33, a USB host and USB OTG
connectors, and 8GB eMMC, an AP6212 WiFi/Bluetooth chip and connectors for
DSI, CSI and GPIOs.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Correct subject prefix case]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

1 files changed, 321 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts b/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts
new file mode 100644
index 000000000000..eaf09666720d
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts
@@ -0,0 +1,321 @@
+/*
+ * Copyright (c) 2017 Free Electrons <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a33.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "BananaPi M2 Magic";
+	compatible = "sinovoip,bananapi-m2m", "allwinner,sun8i-a33";
+
+	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		blue {
+			label = "bpi-m2m:blue:usr";
+			gpios = <&pio 2 7 GPIO_ACTIVE_LOW>;
+		};
+
+		green {
+			label = "bpi-m2m:green:usr";
+			gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>;
+		};
+
+		red {
+			label = "bpi-m2m:red:power";
+			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+	};
+
+	reg_vcc5v0: vcc5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL06 */
+	};
+};
+
+&codec {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc3>;
+};
+
+&cpu0_opp_table {
+	opp@1104000000 {
+		opp-hz = /bits/ 64 <1104000000>;
+		opp-microvolt = <1320000>;
+		clock-latency-ns = <244144>; /* 8 32k periods */
+	};
+
+	opp@1200000000 {
+		opp-hz = /bits/ 64 <1200000000>;
+		opp-microvolt = <1320000>;
+		clock-latency-ns = <244144>; /* 8 32k periods */
+	};
+};
+
+&dai {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+/* This is the i2c bus exposed on the DSI connector for the touch panel */
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "disabled";
+};
+
+/* This is the i2c bus exposed on the GPIO header */
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "disabled";
+};
+
+/* This is the i2c bus exposed on the CSI connector to control the sensor */
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	status = "disabled";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>;
+	vmmc-supply = <&reg_dcdc1>;
+	bus-width = <4>;
+	cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
+	cd-inverted;
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_a>;
+	vmmc-supply = <&reg_aldo1>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp22x: pmic@3a3 {
+		compatible = "x-powers,axp223";
+		reg = <0x3a3>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		eldoin-supply = <&reg_dcdc1>;
+		x-powers,drive-vbus-en;
+	};
+};
+
+#include "axp223.dtsi"
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&reg_aldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-io";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	regulator-name = "vdd-dll";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_dc1sw {
+	regulator-name = "vcc-lcd";
+};
+
+&reg_dc5ldo {
+	regulator-always-on;
+	regulator-min-microvolt = <900000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-3v0";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <900000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <900000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-dram";
+};
+
+/*
+ * Our WiFi chip needs both DLDO1 and DLDO2 to be powered at the same
+ * time, with the two being in sync. Since this is not really
+ * supported right now, just use the two as always on, and we will fix
+ * it later.
+ */
+&reg_dldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi0";
+};
+
+&reg_dldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi1";
+};
+
+&reg_drivevbus {
+	regulator-name = "usb0-vbus";
+	status = "okay";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
+&sound {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_b>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins_a>, <&uart1_pins_cts_rts_a>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+	usb0_vbus_power-supply = <&usb_power_supply>;
+	usb0_vbus-supply = <&reg_drivevbus>;
+	usb1_vbus-supply = <&reg_vcc5v0>;
+	status = "okay";
+};