ARM: dts: Add minimal support for LogicPD Torpedo DM3730 devkit

The LogicPD Torpedo DM3730 devkit consists of a base board and
two processor boards. One of the processor boards has a WLAN and
the other one does not.

Let's set up basic dts file so we can move to device tree only
based booting over next few merge windows. So far I've tested
that UARTs, MMC1, USB OTG, smsc911x, and basic PM support works.

Note that the wireless support in kernel for wl1283 seems to be
broken, it tries to load wl127x-nvs.bin instead of wl128x-nvs.bin
with firmware.

Cc: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

1 files changed, 162 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi
new file mode 100644
index 000000000000..36387b11451d
--- /dev/null
+++ b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi
@@ -0,0 +1,162 @@
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vcc>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		user0 {
+			label = "user0";
+			gpios = <&twl_gpio 18 GPIO_ACTIVE_LOW>;	/* LEDA */
+			linux,default-trigger = "none";
+		};
+	};
+
+	wl12xx_vmmc: wl12xx_vmmc {
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1271";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio5 29 0>;   /* gpio157 */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		vin-supply = <&vmmc2>;
+	};
+};
+
+&gpmc {
+	ranges = <0 0 0x00000000 0x1000000>;	/* CS0: 16MB for NAND */
+
+	nand@0,0 {
+		linux,mtd-name = "micron,mt29f4g16abbda3w";
+		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		nand-bus-width = <16>;
+		ti,nand-ecc-opt = "bch8";
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <44>;
+		gpmc,cs-wr-off-ns = <44>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <34>;
+		gpmc,adv-wr-off-ns = <44>;
+		gpmc,we-off-ns = <40>;
+		gpmc,oe-off-ns = <54>;
+		gpmc,access-ns = <64>;
+		gpmc,rd-cycle-ns = <82>;
+		gpmc,wr-cycle-ns = <82>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		gpmc,device-width = <2>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* u-boot uses mtdparts=omap2-nand.0:512k(x-loader),1920k(u-boot),128k(u-boot-env),4m(kernel),-(fs) */
+
+		x-loader@0 {
+			label = "x-loader";
+			reg = <0 0x80000>;
+		};
+
+		bootloaders@80000 {
+			label = "u-boot";
+			reg = <0x80000 0x1e0000>;
+		};
+
+		bootloaders_env@260000 {
+			label = "u-boot-env";
+			reg = <0x260000 0x20000>;
+		};
+
+		kernel@280000 {
+			label = "kernel";
+			reg = <0x280000 0x400000>;
+		};
+
+		filesystem@680000 {
+			label = "fs";
+			reg = <0x680000 0>;	/* 0 = MTDPART_SIZ_FULL */
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <2600000>;
+
+	twl: twl@48 {
+		reg = <0x48>;
+		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+		interrupt-parent = <&intc>;
+	};
+};
+
+/*
+ * Only found on the wireless SOM. For the SOM without wireless, the pins for
+ * MMC3 can be routed with jumpers to the second MMC slot on the devkit and
+ * gpio157 is not connected. So this should be OK to keep common for now,
+ * probably device tree overlays is the way to go with the various SOM and
+ * jumpering combinations for the long run.
+ */
+&mmc3 {
+	interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
+	pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&wl12xx_vmmc>;
+	non-removable;
+	bus-width = <4>;
+	cap-power-off-card;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1283";
+		reg = <2>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
+		ref-clock-frequency = <26000000>;
+	};
+};
+
+&omap3_pmx_core {
+	mmc3_pins: pinmux_mm3_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat4.sdmmc3_dat0 */
+			OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat5.sdmmc3_dat1 */
+			OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat6.sdmmc3_dat2 */
+			OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat6.sdmmc3_dat3 */
+			OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4)	/* mcbsp4_clkx.gpio_152 */
+			OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4)	/* mcbsp1_fsr.gpio_157 */
+		>;
+	};
+};
+
+&omap3_pmx_core2 {
+	mmc3_core2_pins: pinmux_mmc3_core2_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2)   /* etk_clk.sdmmc3_clk */
+			OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2)   /* etk_ctl.sdmmc3_cmd */
+		>;
+	};
+};
+
+#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&twl {
+	twl_power: power {
+		compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";
+		ti,use_poweroff;
+	};
+};
+
+&twl_gpio {
+	ti,use-leds;
+};