1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
|
/*
* (C) Copyright 2010 - 2011
* NVIDIA Corporation <www.nvidia.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/arch/flow.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/tegra.h>
#include <asm/arch-tegra/ap.h>
#include <asm/arch-tegra/clk_rst.h>
#include <asm/arch-tegra/pmc.h>
#include <asm/arch-tegra/warmboot.h>
#include "warmboot_avp.h"
#define DEBUG_RESET_CORESIGHT
void wb_start(void)
{
struct pmux_tri_ctlr *pmt = (struct pmux_tri_ctlr *)NV_PA_APB_MISC_BASE;
struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
struct flow_ctlr *flow = (struct flow_ctlr *)NV_PA_FLOW_BASE;
struct clk_rst_ctlr *clkrst =
(struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE;
union osc_ctrl_reg osc_ctrl;
union pllx_base_reg pllx_base;
union pllx_misc_reg pllx_misc;
union scratch3_reg scratch3;
u32 reg;
/* enable JTAG & TBE */
writel(CONFIG_CTL_TBE | CONFIG_CTL_JTAG, &pmt->pmt_cfg_ctl);
/* Are we running where we're supposed to be? */
asm volatile (
"adr %0, wb_start;" /* reg: wb_start address */
: "=r"(reg) /* output */
/* no input, no clobber list */
);
if (reg != NV_WB_RUN_ADDRESS)
goto do_reset;
/* Are we running with AVP? */
if (readl(NV_PA_PG_UP_BASE + PG_UP_TAG_0) != PG_UP_TAG_AVP)
goto do_reset;
#ifdef DEBUG_RESET_CORESIGHT
/* Assert CoreSight reset */
reg = readl(&clkrst->crc_rst_dev[TEGRA_DEV_U]);
reg |= SWR_CSITE_RST;
writel(reg, &clkrst->crc_rst_dev[TEGRA_DEV_U]);
#endif
/* TODO: Set the drive strength - maybe make this a board parameter? */
osc_ctrl.word = readl(&clkrst->crc_osc_ctrl);
osc_ctrl.xofs = 4;
osc_ctrl.xoe = 1;
writel(osc_ctrl.word, &clkrst->crc_osc_ctrl);
/* Power up the CPU complex if necessary */
if (!(readl(&pmc->pmc_pwrgate_status) & PWRGATE_STATUS_CPU)) {
reg = PWRGATE_TOGGLE_PARTID_CPU | PWRGATE_TOGGLE_START;
writel(reg, &pmc->pmc_pwrgate_toggle);
while (!(readl(&pmc->pmc_pwrgate_status) & PWRGATE_STATUS_CPU))
;
}
/* Remove the I/O clamps from the CPU power partition. */
reg = readl(&pmc->pmc_remove_clamping);
reg |= CPU_CLMP;
writel(reg, &pmc->pmc_remove_clamping);
reg = EVENT_ZERO_VAL_20 | EVENT_MSEC | EVENT_MODE_STOP;
writel(reg, &flow->halt_cop_events);
/* Assert CPU complex reset */
reg = readl(&clkrst->crc_rst_dev[TEGRA_DEV_L]);
reg |= CPU_RST;
writel(reg, &clkrst->crc_rst_dev[TEGRA_DEV_L]);
/* Hold both CPUs in reset */
reg = CPU_CMPLX_CPURESET0 | CPU_CMPLX_CPURESET1 | CPU_CMPLX_DERESET0 |
CPU_CMPLX_DERESET1 | CPU_CMPLX_DBGRESET0 | CPU_CMPLX_DBGRESET1;
writel(reg, &clkrst->crc_cpu_cmplx_set);
/* Halt CPU1 at the flow controller for uni-processor configurations */
writel(EVENT_MODE_STOP, &flow->halt_cpu1_events);
/*
* Set the CPU reset vector. SCRATCH41 contains the physical
* address of the CPU-side restoration code.
*/
reg = readl(&pmc->pmc_scratch41);
writel(reg, EXCEP_VECTOR_CPU_RESET_VECTOR);
/* Select CPU complex clock source */
writel(CCLK_PLLP_BURST_POLICY, &clkrst->crc_cclk_brst_pol);
/* Start the CPU0 clock and stop the CPU1 clock */
reg = CPU_CMPLX_CPU_BRIDGE_CLKDIV_4 | CPU_CMPLX_CPU0_CLK_STP_RUN |
CPU_CMPLX_CPU1_CLK_STP_STOP;
writel(reg, &clkrst->crc_clk_cpu_cmplx);
/* Enable the CPU complex clock */
reg = readl(&clkrst->crc_clk_out_enb[TEGRA_DEV_L]);
reg |= CLK_ENB_CPU;
writel(reg, &clkrst->crc_clk_out_enb[TEGRA_DEV_L]);
/* Make sure the resets were held for at least 2 microseconds */
reg = readl(TIMER_USEC_CNTR);
while (readl(TIMER_USEC_CNTR) <= (reg + 2))
;
#ifdef DEBUG_RESET_CORESIGHT
/*
* De-assert CoreSight reset.
* NOTE: We're leaving the CoreSight clock on the oscillator for
* now. It will be restored to its original clock source
* when the CPU-side restoration code runs.
*/
reg = readl(&clkrst->crc_rst_dev[TEGRA_DEV_U]);
reg &= ~SWR_CSITE_RST;
writel(reg, &clkrst->crc_rst_dev[TEGRA_DEV_U]);
#endif
/* Unlock the CPU CoreSight interfaces */
reg = 0xC5ACCE55;
writel(reg, CSITE_CPU_DBG0_LAR);
writel(reg, CSITE_CPU_DBG1_LAR);
/*
* Sample the microsecond timestamp again. This is the time we must
* use when returning from LP0 for PLL stabilization delays.
*/
reg = readl(TIMER_USEC_CNTR);
writel(reg, &pmc->pmc_scratch1);
pllx_base.word = 0;
pllx_misc.word = 0;
scratch3.word = readl(&pmc->pmc_scratch3);
/* Get the OSC. For 19.2 MHz, use 19 to make the calculations easier */
reg = (readl(TIMER_USEC_CFG) & USEC_CFG_DIVISOR_MASK) + 1;
/*
* According to the TRM, for 19.2MHz OSC, the USEC_DIVISOR is 0x5f, and
* USEC_DIVIDEND is 0x04. So, if USEC_DIVISOR > 26, OSC is 19.2 MHz.
*
* reg is used to calculate the pllx freq, which is used to determine if
* to set dccon or not.
*/
if (reg > 26)
reg = 19;
/* PLLX_BASE.PLLX_DIVM */
if (scratch3.pllx_base_divm == reg)
reg = 0;
else
reg = 1;
/* PLLX_BASE.PLLX_DIVN */
pllx_base.divn = scratch3.pllx_base_divn;
reg = scratch3.pllx_base_divn << reg;
/* PLLX_BASE.PLLX_DIVP */
pllx_base.divp = scratch3.pllx_base_divp;
reg = reg >> scratch3.pllx_base_divp;
pllx_base.bypass = 1;
/* PLLX_MISC_DCCON must be set for pllx frequency > 600 MHz. */
if (reg > 600)
pllx_misc.dccon = 1;
/* PLLX_MISC_LFCON */
pllx_misc.lfcon = scratch3.pllx_misc_lfcon;
/* PLLX_MISC_CPCON */
pllx_misc.cpcon = scratch3.pllx_misc_cpcon;
writel(pllx_misc.word, &clkrst->crc_pll_simple[SIMPLE_PLLX].pll_misc);
writel(pllx_base.word, &clkrst->crc_pll_simple[SIMPLE_PLLX].pll_base);
pllx_base.enable = 1;
writel(pllx_base.word, &clkrst->crc_pll_simple[SIMPLE_PLLX].pll_base);
pllx_base.bypass = 0;
writel(pllx_base.word, &clkrst->crc_pll_simple[SIMPLE_PLLX].pll_base);
writel(0, flow->halt_cpu_events);
reg = CPU_CMPLX_CPURESET0 | CPU_CMPLX_DBGRESET0 | CPU_CMPLX_DERESET0;
writel(reg, &clkrst->crc_cpu_cmplx_clr);
reg = PLLM_OUT1_RSTN_RESET_DISABLE | PLLM_OUT1_CLKEN_ENABLE |
PLLM_OUT1_RATIO_VAL_8;
writel(reg, &clkrst->crc_pll[CLOCK_ID_MEMORY].pll_out[0]);
reg = SCLK_SWAKE_FIQ_SRC_PLLM_OUT1 | SCLK_SWAKE_IRQ_SRC_PLLM_OUT1 |
SCLK_SWAKE_RUN_SRC_PLLM_OUT1 | SCLK_SWAKE_IDLE_SRC_PLLM_OUT1 |
SCLK_SYS_STATE_IDLE;
writel(reg, &clkrst->crc_sclk_brst_pol);
/* avp_resume: no return after the write */
reg = readl(&clkrst->crc_rst_dev[TEGRA_DEV_L]);
reg &= ~CPU_RST;
writel(reg, &clkrst->crc_rst_dev[TEGRA_DEV_L]);
/* avp_halt: */
avp_halt:
reg = EVENT_MODE_STOP | EVENT_JTAG;
writel(reg, flow->halt_cop_events);
goto avp_halt;
do_reset:
/*
* Execution comes here if something goes wrong. The chip is reset and
* a cold boot is performed.
*/
writel(SWR_TRIG_SYS_RST, &clkrst->crc_rst_dev[TEGRA_DEV_L]);
goto do_reset;
}
/*
* wb_end() is a dummy function, and must be directly following wb_start(),
* and is used to calculate the size of wb_start().
*/
void wb_end(void)
{
}
|
