summaryrefslogtreecommitdiffstats
path: root/board/atmel
Commit message (Collapse)AuthorAgeFilesLines
...
* | arm: atmel: sama5d3: early enable PIO peripheralsBo Shen2013-12-011-0/+6
|/ | | | | | | Enable the PIO peripherals early than other peripherals. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* Merge branch 'iu-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-11-091-0/+11
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h
| * arm: atmel: at91sam9n12ek: add usb host supportBo Shen2013-11-041-0/+11
| | | | | | | | | | | | | | Add usb host support for at91sam9n12ek board. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* | board: arm: convert makefiles to Kbuild styleMasahiro Yamada2013-11-019-199/+19
| | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Vipin Kumar <vipin.kumar@st.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Tom Rini <trini@ti.com>
* | avr32: convert makefiles to Kbuild styleMasahiro Yamada2013-10-313-60/+3
|/ | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Andreas Bießmann <andreas.devel@googlemail.com>
* ARM: atmel: add RNDIS gadget supportBo Shen2013-09-241-0/+13
| | | | | | Add RNDIS gadget support to test atmel usba udc driver Signed-off-by: Bo Shen <voice.shen@atmel.com>
* arm: atmel: remove the config.mk fileBo Shen2013-08-222-2/+0
| | | | | | | | | | remove the config.mk file move text base define to board config file for following boards - at91sam9m10g45ek - at91sam9x5ek Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* arm: atmel: add gmac support for sama5d3xek boardBo Shen2013-08-221-0/+20
| | | | | | | | add gmac support for sama5d3xek board, the gmac embedded in: - sama5d33, sama5d34, sama5d35 Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-2434-568/+34
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* arm: at91sam9n12: change EBI IO to high drive modeBo Shen2013-07-221-1/+1
| | | | | | | | | | | | As both the DDR SDRAM and NAND flash connect to EBI on at91sam9n12 and share the lower 8 bits data line. If use low drive of the data line, it will cause DDR data access corrupt in lower address, so change the data line to high drive mode This will fix the Linux kernel boot issue when use Lower address Signed-off-by: Bo Shen <voice.shen@atmel.com> Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
* ARM: at91sam9n12: add network support with ksz8851_16mllBo Shen2013-06-241-0/+36
| | | | | | | add network support with ksz8851_16mll on at91sam9n12ek board Signed-off-by: Bo Shen <voice.shen@atmel.com> Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
* ARM: atmel: add sama5d3xek supportBo Shen2013-05-212-0/+326
| | | | | | | | | | | | | Add sama5d3xek support with following feature - boot from NAND flash, PMECC support, 4bit ECC @ 512 bytes sector - boot from SPI flash support - boot from SD card support - LCD support - EMAC support - USB OHCI support Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* at91sam9260ek: move board id setup to config headerAndreas Bießmann2013-05-121-12/+0
| | | | | Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: Bo Shen <voice.shen@atmel.com>
* arm: at91: enable mci support for at91sam9g20ek.Wu, Josh2013-05-121-0/+10
| | | | | Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* arm: at91: add at91sam9n12ek board supportWu, Josh2013-05-122-0/+280
| | | | | | | | | | | | Add support for following features: - nand boot, with PMECC 2bit ECC for 512 bytes sector - SPI flash boot - SD card boot - LCD support Signed-off-by: Josh Wu <josh.wu@atmel.com> [fix -Wimplicit-function-declaration for at91_lcd_hw_init()] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* ARM: atmel: add at91sam9g20ek_2mmc nand boot supportBo Shen2013-02-191-1/+6
| | | | | | | | | | Add at91sam9g20_2mmc nand boot support. on this board, there is no dataflash, so disable it change one commet for at91sam9g20ek board Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* at91sam9x5: enable USB support for 9x5ek board.Richard Genoud2012-12-091-0/+3
| | | | | | Signed-off-by: Richard Genoud <richard.genoud@gmail.com> Acked-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* ARM: at91sam9x5: enable MCI0 support for 9x5ek board.Wu, Josh2012-10-171-0/+10
| | | | | Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* Merge remote-tracking branch 'u-boot/master'Albert ARIBAUD2012-09-302-0/+196
|\
| * avr32: add atngw100mkii boardAndreas Bießmann2012-09-132-0/+196
| | | | | | | | | | | | | | | | | | This patch is derived from an older patch provided by atmel in its buildroot-avr32-v3.0.0.tar.bz2 Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> cc: Hans-Christian Egtvedt <egtvedt@samfundet.no> Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
* | at91sam9x5: set default EBI I/O drive configuration.Wu, Josh2012-09-131-0/+4
|/ | | | | | | This patch configure at91sam9x5's EBI drive I/O. Without this, When SD card boot, the nand flash read/write are not stable. Which will cause kernel MTD test fail (Since mainline kernel doesn't configure the EBI register). Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* at91: 9x5: change SMC config timing that both works for PMECC & non-PMECC.Wu, Josh2012-09-011-6/+6
| | | | | | Signed-off-by: Josh Wu <josh.wu@atmel.com> Tested-by: voice.shen@atmel.com Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* arm:at91-boards: remove console_init_f where unnecessaryAndreas Bießmann2012-09-013-9/+0
| | | | | | | | | | | | | | | | A lot of at91 boards have the console_init_f in board_init. This is useless cause it was called before by generic code in lib/board.c. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> cc: Jens Scharsig <esw@bus-elektronik.de> cc: Stelian Pop <stelian@popies.net> cc: Sedji Gaouaou<sedji.gaouaou@atmel.com> cc: Albin Tonnerre <albin.tonnerre@free-electrons.com> cc: Eric Benard <eric@eukrea.com> Tested-by: voice.shen@atmel.com Tested-by: voice.shen@atmel.com Acked-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Tested-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
* at91sam9263ek: remove unnecessary console_init_fAndreas Bießmann2012-09-011-3/+0
| | | | | Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> cc: Stelian Pop <stelian@popies.net>
* arm : at91sam9x5 : fix a small bug for NANDBo Shen2012-09-011-0/+2
| | | | | | | | | fix a bug: when not boot from NAND, the NAND flash can not be detected. Using this to fix it Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* arm : Atmel : add at91sam9x5ek board supportBo Shen2012-09-013-0/+346
| | | | | | | | | | | | Add at91sam9x5ek board support, this board support the following SoCs AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35 Using at91sam9x5ek_nandflash to configure for the board Now only supports NAND with software ECC boot up Signed-off-by: Bo Shen <voice.shen@atmel.com> [move MAINTAINERS entry to right place] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* AT91SAM9*: Change kernel address in dataflash to match u-boot's sizeAlexandre Belloni2012-07-074-12/+12
| | | | | | | | | | | | | | | | | | | | | | | On at91sam platforms, u-boot grew larger than the allocated size in dataflash, the layout was: bootstrap 0x00000000 ubootenv 0x00004200 uboot 0x00008400 kernel 0x00042000 fs 0x00252000 u-boot with the defconfig doesn't seem to fit in 0x42000 - 0x8400 = 0x39C00 bytes anymore. Now, the layout is: bootstrap 0x00000000 ubootenv 0x00004200 uboot 0x00008400 kernel 0x00084000 fs 0x00294000 Signed-off-by: Alexandre Belloni <alexandre.belloni@piout.net> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* Fix: broken boot message at serial line on AT91SAM9263-EK boardesw@bus-elektronik.de2012-07-071-1/+1
| | | | | Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* Fix Stelian's email addressStelian Pop2011-11-2915-15/+15
| | | | | | | Change my old email address which is no longer valid. Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Anatolij Gustschin <agust@denx.de>
* punt unused clean/distclean targetsMike Frysinger2011-10-156-36/+0
| | | | | | | | | | The top level Makefile does not do any recursion into subdirs when cleaning, so these clean/distclean targets in random arch/board dirs never get used. Punt them all. MAKEALL didn't report any errors related to this that I could see. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* led: remove camel casing of led identifiers globallyJason Kridner2011-09-131-6/+6
| | | | | | | | | | | | | | | Result of running the following command to address Wolfgang's comment about camel case: for file in `find . | grep '\.[chS]$'`; do perl -i -pe 's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done Discussion: http://patchwork.ozlabs.org/patch/84988/ Signed-off-by: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* ARM: remove broken "at91rm9200dk" boardWolfgang Denk2011-09-047-877/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* ARM: remove broken "at91cap9adk" boardWolfgang Denk2011-09-045-491/+0
| | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stelian Pop <stelian.pop@leadtechdesign.com>
* atmel: Update support of board AT91SAM9M10G45-EK to new styleThomas Petazzoni2011-09-032-54/+67
| | | | | | Based on earlier work by Alex Waterman <awaterman@dawning.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
* AT91: Makes AT91SAM9263-EK build correctly against u-boot-atmel/masterXu, Hong2011-08-033-34/+46
| | | | | | | | Rework for AT91SAM9263-EK, makes it build again. Based on the work for AT91SAM9260-EK. Signed-off-by: Hong Xu <hong.xu@atmel.com> Signed-off-by: Reinhard Meyer <uboot@emk-elektronik.de>
* AT91: Board fix for AT91SAM9261-EKXu, Hong2011-08-033-67/+77
| | | | | | | Fix board part of AT91SAM9261-EK according to the new scheme Signed-off-by: Hong Xu <hong.xu@atmel.com> Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
* AT91: Makes AT91SAM9RL-EK build correctly against u-boot-atmel/masterXu, Hong2011-08-033-31/+49
| | | | | | | | | Rework for AT91SAM9RL-EK, makes it build again. Based on the work for AT91SAM9260-EK. V4: added changes to MAKEALL Signed-off-by: Hong Xu <hong.xu@atmel.com> Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
* Remove volatile qualifier in get_ram_size() callsAlbert ARIBAUD2011-07-171-1/+1
| | | | | | | | | Checkpatch.pl complains about the volatile qualifier in calls to get_ram_size(). Remove this qualifier in the prototype and in the calls where it is useless, and leave it only in the function body where it is needed. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* Timer: Fix misuse of ARM *timer_masked() functions outside arch/armGraeme Russ2011-07-161-4/+6
| | | | Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
* atstk100x: switch to common cfi driverAndreas Bießmann2011-07-042-233/+0
| | | | | | | | | This patch removes the board implemenatation for flash driver which can now safely switched to the common cfi driver. Compile tested for all atstk100x boards, runtime tested on atstk1002. Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
* at91rm9200ek: use atmel_usartAndreas Bießmann2011-07-041-0/+7
| | | | Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* AT91 rework: fix at91sam(9260/9g20/9xe)ek board port to build again:Reinhard Meyer2011-06-213-64/+72
| | | | | | Make ATMEL's at91sam9260/9g20/9xe-ek boards build again Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
* update arm/at91rm9200 work with rework rework110202Jens Scharsig2011-06-212-12/+14
| | | | | | | | | | | * convert at91rm9200ek and eb_cpux9k2 board to ATMEL_xxx name scheme * Fix: timer.c compile error io.h not found with arm/at91rm9200 * update arm920t/at91 to ATMEL_xxx name scheme * update arm920t/at91 soc lib * update at91_emac driver Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de> Tested-by: Andreas Bießmann <andreas.devel@gmail.com>
* atstk100x: move CONFIG_SYS_TEXT_BASE to headerAndreas Bießmann2011-05-181-1/+0
| | | | Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
* atngw100: move CONFIG_SYS_TEXT_BASE to headerAndreas Bießmann2011-05-181-1/+0
| | | | Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
* avr32: use single linker scriptAndreas Bießmann2011-05-182-144/+0
| | | | | | | This patch move the atstk100x linker script to $(CPUDIR) and delete other pure copies of this file in each board directory. Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
* avr32/config.mk: simplify PLATFORM_RELFLAGSAndreas Bießmann2011-05-182-2/+0
| | | | | | | This patch removes PLATFORM_RELFLAGS from board specific config.mk files and define them in arch specific config.mk file. Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
* avr32: fix linkingAndreas Bießmann2011-05-182-2/+0
| | | | | | | | | | | | | This patch fixes following error: ---8<--- avr32-linux-ld: --gc-sections and -r may not be used together --->8--- Since 8aba9dceebb14144e07d19593111ee3a999c37fc all avr32 boards are broken due to linking error as seen above. Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
* avr32: fixup definitions to ATMEL_BASE_xxxAndreas Bießmann2011-05-182-4/+4
| | | | Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
* Handle most LDSCRIPT setting centrallyScott Wood2011-04-301-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, some linker scripts are found by common code in config.mk. Some are found using CONFIG_SYS_LDSCRIPT, but the code for that is sometimes in arch config.mk and sometimes in board config.mk. Some are found using an arch-specific rule for looking in CPUDIR, etc. Further, the powerpc config.mk rule relied on CONFIG_NAND_SPL when it really wanted CONFIG_NAND_U_BOOT -- which covered up the fact that not all NAND_U_BOOT builds actually wanted CPUDIR/u-boot-nand.lds. Replace all of this -- except for a handful of boards that are actually selecting a linker script in a unique way -- with centralized ldscript finding. If board code specifies LDSCRIPT, that will be used. Otherwise, if CONFIG_SYS_LDSCRIPT is specified, that will be used. If neither of these are specified, then the central config.mk will check for the existence of the following, in order: $(TOPDIR)/board/$(BOARDDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT) $(TOPDIR)/$(CPUDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT) $(TOPDIR)/board/$(BOARDDIR)/u-boot.lds $(TOPDIR)/$(CPUDIR)/u-boot.lds Some boards (sc3, cm5200, munices) provided their own u-boot.lds that were dead code, because they were overridden by a CPUDIR u-boot.lds under the old powerpc rules. These boards' own u-boot.lds have bitrotted and no longer work -- these lds files have been removed. Signed-off-by: Scott Wood <scottwood@freescale.com> Tested-by: Graeme Russ <graeme.russ@gmail.com>
OpenPOWER on IntegriCloud