summaryrefslogtreecommitdiffstats
path: root/arch/arm/cpu
Commit message (Collapse)AuthorAgeFilesLines
...
* | Tegra: Configure L2 cache control reg properly.Tom Warren2013-04-153-8/+51
| | | | | | | | | | | | | | | | | | | | Without this change, kernel fails at calling function cache_clean_flush during kernel early boot. Aprocryphally, intended for T114 only, so I check for a T114 SoC. Works (i.e. dalmore 3.8 kernel now starts printing to console). Signed-off-by: Tom Warren <twarren@nvidia.com>
* | Tegra: Restore cp15 VBAR _start vector write for ARMv7Tom Warren2013-04-151-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | A start vector fix was added by AneeshV for OMAP4 (commit 0d479b53), and caused the old monilithic Tegra builds to hang due to an undefined instruction trap. Previously, the code needed to run on both the AVP (ARM7TDI) and A9, and the AVP doesn't have a CP15 register. I corrected this in commit 6d6c0bae w/#ifndef CONFIG_TEGRA, but now that we use SPL, and boot the AVP w/o any ARMv7 code, I can revert my change, and make Aneesh's change apply to Tegra. Signed-off-by: Tom Warren <twarren@nvidia.com>
* | ARM: tegra: support T33 SKU of Tegra30Stephen Warren2013-04-151-0/+1
|/ | | | | | | | | | | | | | | | | | | Make U-Boot aware of the T33 SKU of Tegra30, and treat it identically to any other Tegra30. An alternative would be to simply remove the SKU checking from tegra_get_chip_type(); most use of the value most likely simply wants to know the current chip, not the specific SKU. Or, the function could be split into separate tegra_get_chip() and tegra_get_sku() for the cases where differentiation really is required. I wonder whether tegra_get_chip_type() should printf() whenever any unkown chip/SKU is found, although perhaps the function is called so early that the printf() wouldn't actually make it to the UART anyway. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
* ARMv7: start.S: stay in HYP mode if u-boot is entered in itAndre Przywara2013-04-151-3/+7
| | | | | | | | | | The KVM and Xen hypervisors for the Cortex-A15 virtualization implementation need to be entered in HYP mode. Should the primary board firmware already enter HYP mode (Calxeda firmware does that), we should not deliberately drop back to SVC mode. Since U-boot does not use the MMU, running in HYP mode is just fine. Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
* ARM: fix CONFIG_SPL_MAX_SIZE semanticsAlbert ARIBAUD2013-04-142-15/+13
| | | | | | | | | | | | | | | | | | | | Remove SPL-related ASSERT() in arch/arm/cpu/u-boot.lds as this file is never used for SPL builds. Rewrite the ASSERT() in arch/arm/cpu/u-boot-spl.lds to separately test image (text,data,rodata...) size, BSS size, and full footprint each against its own max, and make Tegra boards check full footprint. Also, output section mmutable is not used in SPL builds. Remove it. Finally, update README regarding the (now homogeneous) semantics of CONFIG_SPL_[BSS_]MAX_SIZE and add the new CONFIG_SPL_MAX_FOOTPRINT macro. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Reported-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* ARM: Fix __bss_start and __bss_end in linker scriptsAlbert ARIBAUD2013-04-132-8/+20
| | | | | | | | | | | | | | Commit 3ebd1cbc introduced compiler-generated __bss_start and __bss_end__ and commit c23561e7 rewrote all __bss_end__ as __bss_end. Their merge caused silent and harmless but potentially bug-inducing clashes between compiler- and linker- generated __bss_end symbols. Make __bss_end and __bss_start compiler-only, and create __bss_base and __bss_limit for linker-only use. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Reported-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* BUGFIX: arm: data abort in get_bad_stack_swiTetsuyuki Kobayashi2013-04-134-4/+9
| | | | | | | | | | | | | When swi instruction is executed, it is expected to get message "software interrupt" in console and dump registers and reboot, as do_software_interrupt() in arch/arm/lib/interrupts.c. But, actually it causes data abort accessing wrong address in get_bad_stack_swi macro in arch/arm/cpu/v7/start.S. This patch fixes this problem. The same mistake in arch/arm/cpu/{arm1136,arm1176,pxa}/start.S. Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
* Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2013-04-131-2/+2
|\
| * omap3: Display MHz instead of mHz on the consoleman.huber@arcor.de2013-04-121-2/+2
| | | | | | | | | | | | The processor is hopefully running with M(ega)Hz and not with m(illi)Hz. Signed-off-by: Manfred Huber <man.huber@arcor.de>
* | Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-04-124-674/+18
|\ \ | |/ |/| | | | | Conflicts: drivers/video/exynos_fb.c
| * Consolidate bool typeYork Sun2013-04-012-21/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | 'bool' is defined in random places. This patch consolidates them into a single header file include/linux/types.h, using stdbool.h introduced in C99. All other #define, typedef and enum are removed. They are all consistent with true = 1, false = 0. Replace FALSE, False with false. Replace TRUE, True with true. Skip *.py, *.php, lib/* files. Signed-off-by: York Sun <yorksun@freescale.com>
| * Merge branch 'for-v2013.04'Anatolij Gustschin2013-03-292-653/+0
| |\ | | | | | | | | | | | | | | | | | | Conflicts: drivers/video/Makefile Signed-off-by: Anatolij Gustschin <agust@denx.de>
| | * lcd, pxafb: move the pxafb to drivers/videoJeroen Hofstee2013-03-212-651/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since the lcd code was compiled unconditionally for pxa also add CONFIG_PXA_LCD to the boards using this framebuffer. Since driver/video contains video and lcd drivers, add lcd to the name to make clear it belongs to common/lcd.c. cc: Anatolij Gustschin <agust@denx.de> cc: Cliff Brake <cliff.brake@gmail.com> cc: Marek Vasut <marek.vasut@gmail.com> Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
| | * common/lcd.c: cleanup use of global variablesWolfgang Denk2013-03-211-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | lcd_color_fg and lcd_color_bg had to be declared in board specific code, but were not actually used there; in addition, we have getter / setter functions for these, which were not used either. Get rid of the global variables, and use the getter function where needed (so far no setter calls are needed). Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Alessandro Rubini <rubini@unipv.it> Cc: Anatolij Gustschin <agust@denx.de> Cc: Bo Shen <voice.shen@atmel.com> Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: Simon Glass <sjg@chromium.org> Cc: Stelian Pop <stelian@popies.net> Cc: Tom Warren <twarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Jeroen Hofstee <jeroen@myspectrum.nl> [agust: also fixed cm_t35 board while rebasing] Signed-off-by: Anatolij Gustschin <agust@denx.de>
* | | Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2013-04-122-11/+12
|\ \ \
| * | | omap5912-osk: Fix get_timer() and CONFIG_SYS_HZJon Hunter2013-04-101-7/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The function get_timer() should return time in ms and CONFIG_SYS_HZ should be set to 1000 by default. Fix both of these items. Signed-off-by: Jon Hunter <jon-hunter@ti.com>
| * | | OMAP4: Fix bug in omap4460_volts structLubomir Popov2013-04-101-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The omap4460_volts struct was incorrectly referencing tps62361 instead of twl6030 as PMIC for the core and mm voltages (the tps is used for mpu supply only). This shall lead to bad OPP settings while booting kernel. Fixing it. Fix some comments as well. Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
* | | | arm: Make all linker scripts compatible with per-symbol sectionsBenoît Thébaudeau2013-04-126-14/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Let all ARM linker scripts handle properly -ffunction-sections and -fdata-sections. This will be useful for future changes in order to create symbol-specific sections in common .S files. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* | | | arm1176: Remove unused MMU setup from start.SBenoît Thébaudeau2013-04-121-90/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Following the removal of the smdk6400 board, the MMU setup code in arm1176/start.S becomes unused, so remove it. It will still be possible to restore it later from the Git history if necessary, in which case it should be moved out of the relocate_code() function. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* | | | arm: Remove deprecated and now unused NAND SPLBenoît Thébaudeau2013-04-121-8/+4
| | | | | | | | | | | | | | | | Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* | | | arm: Remove support for unused s3c64xxBenoît Thébaudeau2013-04-127-584/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Following the removal of the smdk6400 board, the s3c64xx SoC becomes unused, so remove associated code. It will still be possible to restore it later from the Git history if necessary. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* | | | arm: Remove unused relocate_code() parametersBenoît Thébaudeau2013-04-1213-52/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit e05e5de7fae5bec79617e113916dac6631251156 made the 2 1st parameters of ARM's relocate_code() useless since it moved the code handling them to crt0.S. So, drop these parameters. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* | | | arm926ejs: Remove deprecated and now unused NAND SPLBenoît Thébaudeau2013-04-121-10/+0
| | | | | | | | | | | | | | | | Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* | | | nand: mxc: Switch NAND SPL to generic SPLBenoît Thébaudeau2013-04-121-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This also fixes support for mx31pdk and tx25, which had been broken by commit e05e5de7fae5bec79617e113916dac6631251156. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Acked-by: Scott Wood <scottwood@freescale.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
* | | | imx: Fix automatic make targets for imx imagesBenoît Thébaudeau2013-04-123-2/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Automatically build the 'u-boot.imx' (i.e. imx header + u-boot.bin) and 'SPL' (i.e. imx header + u-boot-spl.bin) make targets for all imx processors supporting this header, so for arm926ejs, arm1136 and armv7. Some combinations were missing. At the same time, fix the build of SPL targets not supporting the imx header on arm1136. For arm1136, the 'SPL' make target was forced to build in all cases if CONFIG_SPL_BUILD was defined, even for non-imx platforms or imx setups without an imx header. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* | | | arm: relocate_code(): Use __image_copy_end for end of relocationBenoît Thébaudeau2013-04-1215-15/+64
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use __image_copy_end instead of __bss_start for the end of the image to relocate. This is the same as commit 033ca72, but applied to all ARM start.S. This is a more appropriate symbol naming for an image copy & relocate feature, and this also saves a useless copy of data put between __image_copy_end and __bss_start in linker scripts (e.g. relocation information, or MMU initialization tables used only before jumping to the relocated image). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* | | | arm: relocate_code(): Remove useless relocation offset computationBenoît Thébaudeau2013-04-1213-66/+39
| | | | | | | | | | | | | | | | Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* | | | arm1136: Remove redundant relocate_code() returnBenoît Thébaudeau2013-04-121-2/+0
| | | | | | | | | | | | | | | | Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* | | | arm: relocate_code() is no longer noreturnBenoît Thébaudeau2013-04-1213-39/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit e05e5de7fae5bec79617e113916dac6631251156 made ARM's relocate_code() return to its caller, but it did not update its declaration accordingly. Fixing this function declaration fixes dropped C code following calls to relocate_code(). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* | | | arm: start.S: Fix _TEXT_BASE for SPLBenoît Thébaudeau2013-04-1214-4/+52
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | _TEXT_BASE must be set to CONFIG_SPL_TEXT_BASE for generic SPL, and to CONFIG_SYS_TEXT_BASE for non-SPL builds. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Reviewed-by: Tom Rini <trini@ti.com>
* | | | imx: mx5: lowlevel_init: Simplify codeBenoît Thébaudeau2013-04-121-6/+2
|/ / / | | | | | | | | | | | | | | | | | | Don't use several instructions to build constant values. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Acked-by: Stefano Babic <sbabic@denx.de>
* | | OMAP3/4/5/AM33xx: Correct logic for checking FAT or RAW MMCTom Rini2013-04-081-3/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the case of booting from certain peripherals, such as UART, we must not see what the device descriptor says for RAW or FAT mode because in addition to being nonsensical, it leads to a hang. This is why we have a test currently for the boot mode being within range. The problem however is that on some platforms we get MMC2_2 as the boot mode and not the defined value for MMC2, and in others we get the value for MMC2_2. This is required to fix eMMC booting on omap5_uevm. Tested on am335x_evm (UART, NAND, SD), omap3_beagle (NAND, SD on classic, SD only on xM rev C5) and omap5_uevm (SD, eMMC). Signed-off-by: Tom Rini <trini@ti.com>
* | | arm: omap4: Fix SDRAM AUTO DETECTIONLokesh Vutla2013-04-083-15/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit "8602114 omap: emif: configure emif only when required" breaks SDRAM_AUTO_DETECTION. The issue is dmm_init() depends on emif_sizes[](SDRAM Auto detection) done in do_sdram_init(). The above commit moves dmm_init() above do_sdram_init() because of which dmm_init() uses uninitialized emif_sizes[]. So instead of using global emif_sizes[], get sdram details locally and calculate emif sizes. Reported-by: Michael Cashwell <mboards@prograde.net> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* | | OMAP: Fix copy-paste bug that did not enable UART4 clockLubomir Popov2013-04-081-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | V2 fixes line wrap issue of the patch itself. UART3 was enabled twice instead of UART4. One more cosmetic change in a comment on EMIF clock. Signed-off-by: Lubomir Popov <lpopov@mm-sol.com> Reviewed-by: R Sricharan <r.sricharan@ti.com>
* | | omap2420-h4: Fix get_timer() and CONFIG_SYS_HZHunter, Jon2013-04-081-2/+6
| | | | | | | | | | | | | | | | | | | | | The function get_timer() should return time in ms and CONFIG_SYS_HZ should be set to 1000 by default. Fix both of these items. Signed-off-by: Jon Hunter <jon-hunter@ti.com>
* | | omap_gpmc: change nandecc commandAndreas Bießmann2013-04-081-8/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With uppcoming BCH support on OMAP devices we need to decide between differnt algorithms when switching the ECC engine. Currently we support 1-bit hammign and 8-bit BCH on HW backend. In order to switch between differnet ECC algorithms we need to change the interface of omap_nand_switch_ecc() also. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Tom Rini <trini@ti.com> Cc: Thomas Weber <thomas.weber.linux@googlemail.com>
* | | asm/omap_gpmc.h: consolidate common definesAndreas Bießmann2013-04-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | arch/arm/include/asm/arch-am33xx/omap_gpmc.h and arch/arm/include/asm/arch-omap3/omap_gpmc.h are almost the same, consolidate the common parts into a new header. Introduce a new asm/omap_gpmc.h which defines the command part and pulls in the architecture specific one. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Tom Rini <trini@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* | | am335x: Enable MMC1 clockTom Rini2013-04-081-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | We must not assume ROM has enabled the clock for MMC1. Reported-by: Koen Kooi <koen@dominion.thruhere.net> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
* | | Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD2013-04-044-106/+256
|\ \ \
| * | | Exynos: pwm: Remove dead code of function exynos5_get_pwm_clkAkshay Saraswat2013-04-011-21/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As we shall now be using clock_get_periph_rate function. We find no reason for keeping code in function exynos5_get_pwm_clk. Hence, removing it. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | | Exynos: pwm: Use generic api to get pwm clk freqPadmavathi Venna2013-04-011-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use generic api to get the pwm clock frequency Test with command "sf probe 1:0; time sf read 40008000 0 1000". Try with different numbers of bytes and see that sane values are obtained Build and boot U-boot with this patch, backlight works properly. Signed-off-by: Padmavathi Venna <padma.v@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | | Exynos: clock: Add generic api to get the clk freqPadmavathi Venna2013-04-011-0/+144
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add generic api to get the frequency of the required peripherial. This API gets the source clock frequency and returns the required frequency by dividing with first and second dividers based on the requirement. Test with command "sf probe 1:0; time sf read 40008000 0 1000". Try with different numbers of bytes and see that sane values are obtained Build and boot U-boot with this patch, backlight works properly. Signed-off-by: Padmavathi Venna <padma.v@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | | Exynos: Tidy up the pwm_config function in the exynos pwm driverGabe Black2013-04-011-16/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some small fixes in the exynos pwm driver: 1. NS_IN_HZ is non-sensical since these are not compatible units. This constant actually describes the number of nanoseconds in a second. Renamed it to NS_IN_SEC. Also dropped the unnecessary parenthesis. 2. The variable "period" is not used to hold a period, it's used to hold a frequency. Renamed it to "frequency". 3. tcmp is an unsigned value, so (tcmp < 0) will never be true and the if which checks that condition will never execute. Also, there should be no problem if the pwm never switches, so there's no reason to subtract one from tcmp and therefore no reason to compare it against zero. Removed both ifs. If they weren't removed, tcmp should be a signed value. 4. Add a check for a 0 period. Test with command "sf probe 1:0; time sf read 40008000 0 1000". Try with different numbers of bytes and see that sane values are obtained Build and boot U-boot with this patch, backlight works properly. Signed-off-by: Gabe Black <gabeblack@google.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | | Exynos: Avoid a divide by zero by specifying a non-zero period for pwm 4Gabe Black2013-04-011-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The pwm_config function in the exynos pwm driver divides by its period period parameter. A function was calling pwm_config with a 0ns period and a 0ns duty cycle. That doesn't actually make any sense physically, and results in a divide by zero in the driver. This change changes the parameters to be a 100000ns period and duty cycle. Test with command "sf probe 1:0; time sf read 40008000 0 1000". Try with different numbers of bytes and see that sane values are obtained Build and boot U-boot with this patch, backlight works properly. Signed-off-by: Gabe Black <gabeblack@google.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | | Exynos: pwm: Fix two bugs in the exynos pwm configuration codeGabe Black2013-04-011-10/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | First, the "div" value was being used incorrectly to compute the frequency of the PWM timer. The value passed in is a constant which reflects the value that would be found in a configuration register, 0 to 4. That should correspond to a scaling factor of 1, 2, 4, 8, or 16, 1 << div, but div + 1 was being used instead. Second, the reset value of the timers were being calculated to give an overall frequency, thrown out, and set to a maximum value. This was done so that PWM 4 could be used as the system clock by counting down from a high value, but it was applied indiscriminantly. It should at most be applied only to PWM 4. This change also takes the opportunity to tidy up the pwm_init function. Test with command "sf probe 1:0; time sf read 40008000 0 1000". Try with different numbers of bytes and see that sane values are obtained Build and boot U-boot with this patch, backlight works properly. Signed-off-by: Gabe Black <gabeblack@google.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | | Exynos: Add timer_get_us functionChe-Liang Chiou2013-04-011-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | timer_get_us returns the time in microseconds since a certain reference point of history. However, it does not guarantee to return an accurate time after a long period; instead, it wraps around (that is, the reference point is reset to some other point of history) after some periods. The frequency of wrapping around is about an hour (or 2^32 microseconds). Test with command "sf probe 1:0; time sf read 40008000 0 1000". Try with different numbers of bytes and see that sane values are obtained Signed-off-by: Che-Liang Chiou <clchiou@chromium.org> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | | Exynos: Change get_timer() to work correctlySimon Glass2013-04-012-62/+44
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | At present get_timer() does not return sane values. It should count up smoothly in milliscond intervals. We can change the PWM to count down at 1MHz, providing a resolution of 1us and a range of about an hour between required get_timer() calls. Test with command "sf probe 1:0; time sf read 40008000 0 1000". Try with different numbers of bytes and see that sane values are obtained Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | | EXYNOS5: Add L2 Cache Support.Rajeshwari Shinde2013-03-271-0/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch set adds L2 Cache Support to EXYNOS. Signed-off-by: Arun Mankuzhi <arun.m@samsung.com> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | | | Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2013-04-042-9/+21
|\ \ \ \
| * | | | mx6: Fix get_board_rev() for the mx6 solo caseFabio Estevam2013-04-031-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When booting a Freescale kernel 3.0.35 on a Wandboard solo, the get_board_rev() returns 0x62xxx, which is not a value understood by the VPU (Video Processing Unit) library in the kernel and causes the video playback to fail. The expected values for get_board_rev are: 0x63xxx: For mx6quad/dual 0x61xxx: For mx6dual-lite/solo So adjust get_board_rev() accordingly and make it as weak function, so that we do not need to define it in every mx6 board file. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
OpenPOWER on IntegriCloud