summaryrefslogtreecommitdiffstats
path: root/arch/arm/cpu/armv7
Commit message (Collapse)AuthorAgeFilesLines
* ARM: OMAP3: rx51: Enable workaround for ARM errata 454179, 430973, 621766Nishanth Menon2015-03-131-25/+20
| | | | | | | | | | | | RX51 has a secure logic which uses different parameters compared to traditional implementation. So, make the generic secure acr write over-ride-able by board file and refactor rx51 code to use this. While at it, enable the OMAP3 specific errata code for 454179, 430973, 621766. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: OMAP3: Enable workaround for ARM errata 454179, 430973, 621766Nishanth Menon2015-03-131-21/+10
| | | | | | | | | Enable the OMAP3 specific errata code for 454179, 430973, 621766 and while at it, remove legacy non-revision checked errata logic. Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: OMAP5 / DRA7: Setup L2 Aux Control Register with recommended configurationNishanth Menon2015-03-131-0/+16
| | | | | | | | | | | Update to existing recommendation for L2ACTLR configuration to prevent system instability and optimize performance. These apply to both OMAP5 and DRA7. Reported-by: Vivek Chengalvala <vchengalvala@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: DRA7 / OMAP5: Add workaround for ARM errata 798870Praveen Rao2015-03-131-0/+7
| | | | | | | | | | | | | | | | | | | This patch enables the workaround for ARM errata 798870 for OMAP5 / DRA7 which says "If back-to-back speculative cache line fills (fill A and fill B) are issued from the L1 data cache of a CPU to the L2 cache, the second request (fill B) is then cancelled, and the second request would have detected a hazard against a recent write or eviction (write B) to the same cache line as fill B then the L2 logic might deadlock." An l2auxctlr accessor implementation for OMAP5 and DRA7 is introduced here as well. Signed-off-by: Praveen Rao <prao@ti.com> Signed-off-by: Angela Stegmaier <angelabaker@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: OMAP3: Get rid of omap3_gp_romcode_call and replace with omap_smc1Nishanth Menon2015-03-134-16/+5
| | | | | | | | | | | | omap_smc1 is now generic enough to remove duplicate omap3_gp_romcode_call logic that omap3 introduced. As part of this change, move to using the generic lowlevel_init.S for omap3 as well. Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: OMAP: Change set_pl310_ctrl_reg to be genericNishanth Menon2015-03-132-9/+13
| | | | | | | | | | | | | | | | | | | set_pl310_ctrl_reg does use the Secure Monitor Call (SMC) to setup PL310 control register, however, that is something that is generic enough to be used for OMAP5 generation of processors as well. The only difference being the service being invoked for the function. So, convert the service to a macro and use a generic name (same as that used in Linux for some consistency). While at that, also add a data barrier which is necessary as per recommendation. While at this, smc #0 is maintained as handcoded assembly thanks to various gcc version eccentricities, discussion thread: http://marc.info/?t=142542166800001&r=1&w=2 Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: Introduce erratum workaround for 621766Nishanth Menon2015-03-131-0/+13
| | | | | | | | | | | | | 621766: Under a specific set of conditions, executing a sequence of NEON or vfp load instructions can cause processor deadlock Impacts: Every Cortex-A8 processors with revision lower than r2p1 Work around: Set L1NEON to 1 Based on ARM errata Document revision 20.0 (13 Nov 2010) Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: Introduce erratum workaround for 430973Nishanth Menon2015-03-131-0/+13
| | | | | | | | | | | | | 430973: Stale prediction on replaced inter working branch causes Cortex-A8 to execute in the wrong ARM/Thumb state Impacts: Every Cortex-A8 processors with revision lower than r2p1 Work around: Set IBE to 1 Based on ARM errata Document revision 20.0 (13 Nov 2010) Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: Introduce erratum workaround for 454179Nishanth Menon2015-03-132-0/+19
| | | | | | | | | | | | | | | 454179: Stale prediction may inhibit target address misprediction on next predicted taken branch Impacts: Every Cortex-A8 processors with revision lower than r2p1 Work around: Set IBE and disable branch size mispredict to 1 Also provide a hook for SoC specific handling to take place if needed. Based on ARM errata Document revision 20.0 (13 Nov 2010) Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: Introduce erratum workaround for 798870Nishanth Menon2015-03-133-2/+48
| | | | | | | | | | | | | | | | | | | | | | | Add workaround for Cortex-A15 ARM erratum 798870 which says "If back-to-back speculative cache line fills (fill A and fill B) are issued from the L1 data cache of a CPU to the L2 cache, the second request (fill B) is then cancelled, and the second request would have detected a hazard against a recent write or eviction (write B) to the same cache line as fill B then the L2 logic might deadlock." Implementations for SoC families such as Exynos, OMAP5/DRA7 etc will be widely different. Every SoC has slightly different manner of setting up access to L2ACLR and similar registers since the Secure Monitor handling of Secure Monitor Call(smc) is diverse. Hence an weak function is introduced which may be overriden to implement SoC specific accessor implementation. Based on ARM errata Document revision 18.0 (22 Nov 2013) Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* Merge branch 'master' of git://git.denx.de/u-boot-tegraTom Rini2015-03-101-1/+8
|\ | | | | | | | | | | | | Conflicts: README Signed-off-by: Tom Rini <trini@konsulko.com>
| * ARM: HYP/non-sec: relocation before enable secondary coresPeng Fan2015-03-011-1/+8
| | | | | | | | | | | | | | | | | | | | If CONFIG_ARMV7_PSCI is not defined and CONFIG_ARMV7_SECURE_BASE is defined, smp_kicl_all_cpus may enable secondary cores and runs into secure_ram_addr( _smp_pen), before code is relocated to secure ram. So need relocation to secure ram before enable secondary cores. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com>
* | ARM: PSCI: Rework the DT handler slightlyTom Rini2015-03-091-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The way the PSCI DT update happens currently means we pull in <asm/armv7.h> everywhere, including on ARMv8 and that in turn brings in <asm/io.h> for some non-PSCI related things that header needs to deal with. To fix this, we rework the hook slightly. A good portion of arch/arm/cpu/armv7/virt-dt.c is common looking and I hope that when PSCI is needed on ARMv8 we can re-use this by and large. So rename the current hook to psci_update_dt(), move the prototype to <asm/psci.h> and add an #ifdef that will make re-use later easier. Reported-by: York Sun <yorksun@freescale.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: York Sun <yorksun@freescale.com> Cc: Ian Campbell <ijc@hellion.org.uk> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: York Sun <yorksun@freescale.com>
* | omap: gpmc: 'nandecc sw' can use HAM1 or BCH8Ash Charles2015-03-051-1/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The 'nandecc sw' command selects a software-based error correction algorithm. By default, this is OMAP_ECC_HAM1_CODE_SW but some platforms use OMAP_ECC_BCH8_CODE_HW_DETECTION_SW as their software-based correction algorithm. Allow a user to be specific e.g. # nandecc sw <hamming|bch8> where 'hamming' is still the default. Note: we don't just use CONFIG_NAND_OMAP_ECCSCHEME as it might be set to a hardware-based ECC scheme---a little strange when the user has requested 'sw' ECC. Signed-off-by: Ash Charles <ashcharles@gmail.com>
* | omap3: add support for QUIPOS Cairo board.Albert ARIBAUD \(3ADEV\)2015-03-051-0/+5
| | | | | | | | | | | | | | | | This patch extends OMAP3 support for AM/DM37xx and introduces the AM3703-based Quipos Cairo board. Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr> Reviewed-by: Simon Glass <sjg@chromium.org>
* | Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2015-03-051-0/+29
|\ \
| * \ Merge branch 'master' of git://git.denx.de/u-bootStefano Babic2015-03-0259-4184/+808
| |\ \
| * | | ARM: imx6 Add WDOG3 for i.MX6SXPeng Fan2015-02-171-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | There are three wdogs for i.MX 6SoloX. Add wdog3 support in function imx_set_wdog_powerdown. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
| * | | ARM: imx6: disable bandgap self-bias after bootPeng Fan2015-02-171-0/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The self-bias circuit is used by the bandgap during startup. Once the bandgap has stabilized, the self-bias circuit should be disabled for best noise performance of analog blocks. Also this bit should be disabled before the chip enters STOP mode or when ever the regular bandgap is disabled. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Signed-off-by: Ranjani Vaidyanathan <Ranjani.Vaidyanathan@freescale.com>
* | | | ti: armv7: Move SPL SDRAM init to the right place, drop unused CONFIG_SPL_STACKSimon Glass2015-03-043-9/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently in some cases SDRAM init requires global_data to be available and soon this will not be available prior to board_init_f(). Adjust the code paths in these cases to be correct. In some cases we had the SPL stack be in DDR as we might have large stacks (due to Falcon Mode + Environment). In these cases switch to CONFIG_SPL_STACK_R. In other cases we had simply been setting CONFIG_SPL_STACK into SRAM. In these cases we no longer need to (CONFIG_SYS_INIT_SP_ADDR is used and is also in SRAM) so drop those lines. Signed-off-by: Simon Glass <sjg@chromium.org> Tested on Beagleboard, Beagleboard xM Tested-by: Matt Porter <mporter@konsulko.com> Tested on Beaglebone Black, AM43xx GP EVM, OMAP5 uEVM, OMAP4 Pandaboard Tested-by: Tom Rini <trini@konsulko.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* | | | arm: Reduce the scope of lowlevel_init()Simon Glass2015-03-041-2/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This function has grown into something of a monster. Some boards are setting up a console and DRAM here in SPL. This requires global_data which should be set up in one place (crt0.S). There is no need for SPL to use s_init() for anything since board_init_f() is called immediately afterwards. Signed-off-by: Simon Glass <sjg@chromium.org>
* | | | Merge branch 'master' of git://git.denx.de/u-boot-samsungTom Rini2015-03-016-35/+342
|\ \ \ \
| * | | | Exynos: Fix L2 cache timings on Exynos5420 and Exynos5800Doug Anderson2015-02-283-93/+77
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It was found that the L2 cache timings that we had before could cause freezes and hangs. We should make things more robust with better timings. Currently the production ChromeOS kernel applies these timings, but it's nice to fixup firmware too (and upstream probably won't take our kernel hacks). This also provides a big cleanup of the L2 cache init code avoiding some duplication. The way things used to work: * low_power_start() was installed by the SPL (both at boot and resume time) and left resident in iRAM for the kernel to use when bringing up additional CPUs. It used configure_l2_ctlr() and configure_l2_actlr() when it detected it was on an A15. This was needed (despite the L2 cache registers being shared among all A15s) because we might have been the first man in after the whole A15 cluster was shutdown. * secondary_cores_configure() was called on at boot time and at resume time. Strangely this called configure_l2_ctlr() but not configure_l2_actlr() which was almost certainly wrong. Given that we'll call both (see next bullet) later in the boot process it didn't matter for normal boot, but I guess this is how L2 cache settings got set on 5420/5800 (but not 5250?) at resume time. * exynos5_set_l2cache_params() was called as part of cache enablement. This should happen at boot time (normally in the SPL except for USB boot where it happens in main U-Boot). Note that the old code wasn't setting ECC/parity in the cache enablement code but we happened to get it anyway because we'd call secondary_cores_configure() at boot time. For resume time we'd get it anyway when the 2nd A15 core came up. Let's make this a whole lot simpler. Now we always set these parameters in the same place for all boots and use the same code for setting up secondary CPUs. Intended net effects of this change (other than cleanup): * Timings go from before: data: 0 cycle setup, 3 cycles (0x2) latency tag: 0 cycle setup, 3 cycles (0x2) latency after: data: 1 cycle setup, 4 cycles (0x3) latency tag: 1 cycle setup, 4 cycles (0x3) latency * L2ACTLR is properly initted on 5420/5800 in all cases. One note is that we're still relying on luck to keep low_power_start() working. The compiler is being nice and not storing anything on the stack. Another note is that on its own this patch won't help to fix cache settings in an RW U-Boot update where we still have the RO SPL. The plan for that is: * Have RW U-Boot re-init the cache right before calling the kernel (after it has turned the L2 cache off). This is why the functions are in a header file instead of lowlevel_init.c. * Have the kernel save the L2 cache settings of the boot CPU and apply them to all other CPUs. We get a little lucky here because the old code was using "|=" to modify the registers and all of the bits that it's setting are also present in the new settings (!). That means that when the 2nd CPU in the A15 cluster comes up it doesn't actually mess up the settings of the 1st CPU in the A15 cluster. An alternative option is to have the kernel write its own low_power_start() code. Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | | | Exynos542x: Make A7s boot with thumb-mode U-Boot on warm resetAkshay Saraswat2015-02-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On warm reset, all cores jump to the low_power_start function because iRAM data is retained and because while executing iROM code all cores find the jump flag 0x02020028 set. In low_power_start, cores check the reset status and if true they clear the jump flag and jump back to 0x0. The A7 cores do jump to 0x0 but consider following instructions as a Thumb instructions which in turn makes them loop inside the iROM code instead of jumping to power_down_core. This issue is fixed by replacing the "mov pc" instruction with a "bx" instruction which switches state along with the jump to make the execution unit consider the branch target as an ARM instruction. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | | | Exynos542x: Fix secondary core booting for thumbAkshay Saraswat2015-02-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When compiled SPL for Thumb secondary cores failed to boot at the kernel boot up. Only one core came up out of 4. This was happening because the code relocated to the address 0x02073000 by the primary core was an ARM asm code which was executed by the secondary cores as if it was a thumb code. This patch fixes the issue of secondary cores considering relocated code as Thumb instructions and not ARM instructions by jumping to the relocated with the help of "bx" ARM instruction. "bx" instruction changes the 5th bit of CPSR which allows execution unit to consider the following instructions as ARM instructions. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | | | Exynos542x: add L2 control register configurationAkshay Saraswat2015-02-282-13/+64
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch does 3 things: 1. Enables ECC by setting 21st bit of L2CTLR. 2. Restore data and tag RAM latencies to 3 cycles because iROM sets 0x3000400 L2CTLR value during switching. 3. Disable clean/evict push to external by setting 3rd bit of L2ACTLR. We need to restore this here due to switching. Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | | | Exynos542x: cache: Disable clean/evict push to externalAkshay Saraswat2015-02-281-1/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | L2 Auxiliary Control Register provides configuration and control options for the L2 memory system. Bit 3 of L2ACTLR stands for clean/evict push to external. Setting bit 3 disables clean/evict which is what this patch intends to do. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | | | Exynos542x: Add workaround for exynos iROM errataAkshay Saraswat2015-02-283-16/+200
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | iROM logic provides undesired jump address for CPU2. This patch adds a programmable susbstitute for a part of iROM logic which wakes up cores and provides jump addresses. This patch creates a logic to make all secondary cores jump to a particular address which evades the possibility of CPU2 jumping to wrong address and create undesired results. Logic of the workaround: Step-1: iROM code checks value at address 0x2020028. Step-2: If value is 0xc9cfcfcf, it jumps to the address (0x202000+CPUid*4), else, it continues executing normally. Step-3: Primary core puts secondary cores in WFE and store 0xc9cfcfcf in 0x2020028 and jump address (pointer to function low_power_start) in (0x202000+CPUid*4). Step-4: When secondary cores recieve event signal they jump to this address and continue execution. Signed-off-by: Kimoon Kim <kimoon.kim@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | | | Exynos542x: CPU: Power down all secondary coresAkshay Saraswat2015-02-282-0/+72
| | |/ / | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds code to shutdown secondary cores. When U-boot comes up, all secondary cores appear powered on, which is undesirable and causes side effects while initializing these cores in kernel. Secondary core power down happens in following steps: Step-1: After Exynos power-on, primary core starts executing first. Step-2: In iROM code every core has to check 2 flags i.e. addresses 0x02020028 & 0x02020004. Step-3: Initially 0x02020028 is 0 for all cores and 0x02020004 has a jump address for primary core and 0 for all secondary cores. Step-4: Therefore, primary core follows normal iROM execution and jumps to BL1 eventually, whereas all secondary cores enter WFE. Step-5: When primary core comes into function secondary_cores_configure, it puts pointer to function power_down_core into 0x02020004 and provides DSB and SEV for all cores so that they may come out of WFE and jump to power_down_core function. Step-6: And ultimately because of power_down_core all secondary cores shut-down. Signed-off-by: Kimoon Kim <kimoon.kim@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | | | Merge branch 'master' of git://git.denx.de/u-boot-uniphierTom Rini2015-03-0159-3588/+0
|\ \ \ \
| * | | | ARM: UniPhier: move SoC sources to mach-uniphierMasahiro Yamada2015-03-0159-3588/+0
| |/ / / | | | | | | | | | | | | | | | | | | | | | | | | Move arch/arm/cpu/armv7/uniphier/* -> arch/arm/mach-uniphier/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | | Merge branch 'rmobile' of git://git.denx.de/u-boot-shTom Rini2015-03-013-14/+1141
|\ \ \ \ | |/ / / |/| | |
| * | | arm: rmobile: Add Porter board supportVladimir Barinov2015-02-251-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Porter is an entry level development board based on R-Car M2 SoC (R8A7791) This commit supports the following peripherals: - SCIF, I2C, Ethernet, QSPI, SD, USB Host Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * | | arm: rmobile: lager: Add support SDHINobuhiro Iwamatsu2015-02-251-8/+993
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Lager board has two SDHI port as SDHI0 and SDHI2. This adds GPIO configuration and initialization function of SDHI, and enables MMC command. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * | | arm: rmobile: alt: Add support SDHINobuhiro Iwamatsu2015-02-251-5/+143
| | |/ | |/| | | | | | | | | | | | | | | | | | | | | | Alt board has two SDHI port. This adds GPIO configuration and initialization function of SDHI, and enables MMC command. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* | | Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini2015-02-251-10/+221
|\ \ \
| * | | arm: ls102xa: workaround for cache coherency problemchenhui zhao2015-02-241-0/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The RCPM FSM may not be reset after power-on, for example, in the cases of cold boot and wakeup from deep sleep. It causes cache coherency problem and may block deep sleep. Therefore, reset them if they are not be reset. Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | | arm/ls102xa: create TLB to map PCIe regionMinghuan Lian2015-02-241-10/+193
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | LS1021A's PCIe1 region begins 0x40_00000000; PCIe2 begins 0x48_00000000. In order to access PCIe device, we must create TLB to map the 40bit physical address to 32bit virtual address. This patch will enable MMU after DDR is available and creates MMU table in DRAM to map all 4G space; then, re-use the reserved space to map PCIe region. The following the mapping layout. VA mapping: ------- <---- 0GB | | | | |-------| <---- 0x24000000 |///////| ===> 192MB VA map for PCIe1 with offset 0x40_0000_0000 |-------| <---- 0x300000000 | | |-------| <---- 0x34000000 |///////| ===> 192MB VA map for PCIe2 with offset 0x48_0000_0000 |-------| <---- 0x40000000 | | |-------| <---- 0x80000000 DDR0 space start |\\\\\\\| |\\\\\\\| ===> 2GB VA map for 2GB DDR0 Memory space |\\\\\\\| ------- <---- 4GB DDR0 space end Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | | kconfig: remove unneeded dependency on !SPL_BUILDMasahiro Yamada2015-02-244-22/+21
| | | | | | | | | | | | | | | | | | | | | Now CONFIG_SPL_BUILD is not defined in Kconfig, so "!depends on SPL_BUILD" and "if !SPL_BUILD" are redundant. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | kconfig: switch to single .config configurationMasahiro Yamada2015-02-241-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When Kconfig for U-boot was examined, one of the biggest issues was how to support multiple images (Normal, SPL, TPL). There were actually two options, "single .config" and "multiple .config". After some discussions and thought experiments, I chose the latter, i.e. to create ".config", "spl/.config", "tpl/.config" for Normal, SPL, TPL, respectively. It is true that the "multiple .config" strategy provided us the maximum flexibility and helped to avoid duplicating CONFIGs among Normal, SPL, TPL, but I have noticed some fatal problems: [1] It is impossible to share CONFIG options across the images. If you change the configuration of Main image, you often have to adjust some SPL configurations correspondingly. Currently, we cannot handle the dependencies between them. It means one of the biggest advantages of Kconfig is lost. [2] It is too painful to change both ".config" and "spl/.config". Sunxi guys started to work around this problem by creating a new configuration target. Commit cbdd9a9737cc (sunxi: kconfig: Add %_felconfig rule to enable FEL build of sunxi platforms.) added "make *_felconfig" to enable CONFIG_SPL_FEL on both images. Changing the configuration of multiple images in one command is a generic demand. The current implementation cannot propose any good solution about this. [3] Kconfig files are getting ugly and difficult to understand. Commit b724bd7d6349 (dm: Kconfig: Move CONFIG_SYS_MALLOC_F_LEN to Kconfig) has sprinkled "if !SPL_BUILD" over the Kconfig files. [4] The build system got more complicated than it should be. To adjust Linux-originated Kconfig to U-Boot, the helper script "scripts/multiconfig.sh" was introduced. Writing a complicated text processor is a shell script sometimes caused problems. Now I believe the "single .config" will serve us better. With it, all the problems above would go away. Instead, we will have to add some CONFIG_SPL_* (and CONFIG_TPL_*) options such as CONFIG_SPL_DM, but we will not have much. Anyway, this is what we do now in scripts/Makefile.spl. I admit my mistake with my apology and this commit switches to the single .config configuration. It is not so difficult to do that: - Remove unnecessary processings from scripts/multiconfig.sh This file will remain for a while to support the current defconfig format. It will be removed after more cleanups are done. - Adjust some makefiles and Kconfigs - Add some entries to include/config_uncmd_spl.h and the new file scripts/Makefile.uncmd_spl. Some CONFIG options that are not supported on SPL must be disabled because one .config is shared between SPL and U-Boot proper going forward. I know this is not a beautiful solution and I think we can do better, but let's see how much we will have to describe them. - update doc/README.kconfig More cleaning up patches will follow this. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* | | ARM: UniPhier: set CONFIG_SYS_MALLOC_F to the global default valueMasahiro Yamada2015-02-241-1/+1
|/ / | | | | | | | | | | | | | | | | It is true that malloc is necessary for Driver Model before relocation, but there is no good reason to reserve the malloc space more than enough. The default value 0x400 works well. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* | bcm2836 SoC support (used in Raspberry Pi 2 model B)Stephen Warren2015-02-212-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | The bcm2835 and bcm2836 are essentially identical, except: - The CPU is an ARM1176 v.s. a quad-core Cortex-A7. - The physical address of many IO controllers has moved. Rather than introducing a whole new bcm2836 value for $(SOC) or $(ARCH), update the existing bcm2835 code to handle the minor differences, and plumb it into the ARMv7 CPU architecture. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
* | ARM: keystone: move SoC sources to mach-keystoneMasahiro Yamada2015-02-2115-2190/+0
| | | | | | | | | | | | | | | | Move arch/arm/cpu/armv7/keystone/* -> arch/arm/mach-keystone/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Rini <trini@ti.com>
* | ARM: highbank: move SoC sources to mach-highbankMasahiro Yamada2015-02-214-55/+0
| | | | | | | | | | | | | | | | Move arch/arm/cpu/armv7/highbank/* -> arch/arm/mach-highbank/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Rob Herring <robh@kernel.org>
* | ARM: tegra: collect SoC sources into mach-tegraMasahiro Yamada2015-02-2111-736/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit moves files as follows: arch/arm/cpu/arm720t/tegra20/* -> arch/arm/mach-tegra/tegra20/* arch/arm/cpu/arm720t/tegra30/* -> arch/arm/mach-tegra/tegra30/* arch/arm/cpu/arm720t/tegra114/* -> arch/arm/mach-tegra/tegra114/* arch/arm/cpu/arm720t/tegra124* -> arch/arm/mach-tegra/tegra124/* arch/arm/cpu/arm720t/tegra-common/* -> arch/arm/mach-tegra/* arch/arm/cpu/armv7/tegra20/* -> arch/arm/mach-tegra/tegra20/* arch/arm/cpu/armv7/tegra30/* -> arch/arm/mach-tegra/tegra30/* arch/arm/cpu/armv7/tegra114/* -> arch/arm/mach-tegra/tegra114/* arch/arm/cpu/armv7/tegra124/* -> arch/arm/mach-tegra/tegra124/* arch/arm/cpu/armv7/tegra-common/* -> arch/arm/mach-tegra/* arch/arm/cpu/tegra20-common/* -> arch/arm/mach-tegra/tegra20/* arch/arm/cpu/tegra30-common/* -> arch/arm/mach-tegra/tegra30/* arch/arm/cpu/tegra114-common/* -> arch/arm/mach-tegra/tegra114/* arch/arm/cpu/tegra124-common/* -> arch/arm/mach-tegra/tegra124/* arch/arm/cpu/tegra-common/* -> arch/arm/mach-tegra/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Tested-by: Simon Glass <sjg@chromium.org> [ on nyan-big ] Cc: Stephen Warren <swarren@nvidia.com> Cc: Tom Warren <twarren@nvidia.com>
* | ARM: at91: collect SoC sources into mach-at91Masahiro Yamada2015-02-219-742/+0
| | | | | | | | | | | | | | | | | | | | | | | | This commit moves source files as follows: arch/arm/cpu/arm920t/at91/* -> arch/arm/mach-at91/arm920t/* arch/arm/cpu/arm926ejs/at91/* -> arch/arm/mach-at91/arm926ejs/* arch/arm/cpu/armv7/at91/* -> arch/arm/mach-at91/armv7/* arch/arm/cpu/at91-common/* -> arch/arm/mach-at91/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Andreas Bießmann <andreas.devel@googlemail.co>
* | Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini2015-02-1710-93/+133
|\ \
| * | sunxi: Support the FEL boot mode in the regular u-boot buildSiarhei Siamashka2015-02-163-10/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | So that the CONFIG_SPL_FEL option is not needed anymore. And the regular SPL binary, generated by the default u-boot build, is now also bootable over USB in the FEL mode. The SPL still can boot from the SD card too. A bunch of system registers need to be saved/restored in order to ensure that the IRQ handler still works in the BROM FEL code after getting control back from the SPL. This is done in the sunxi code instead of abusing ifdefs in 'start.S'. The decision whether to load the main u-boot binary from the SD card or return to the FEL code in the BROM is done at runtime. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> [hdegoede@redhat.com: Since we now restore various regs before returning to the FEL BROM code we can drop the sunxi specific #ifdefs in start.S] Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
| * | sunxi: Normalise FEL supportSimon Glass2015-02-166-88/+51
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Make sunxi's FEL code fit with the normal U-Boot boot sequence instead of creating its own. There are some #ifdefs required in start.S. Future work will hopefully remove these. This series is available at u-boot-dm, branch sunxi-working. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
| * | arm: Allow lr to be saved by board codeSimon Glass2015-02-164-5/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The link register value can be required on some boards (e.g. FEL mode on sunxi) so use a branch instruction to jump to save_boot_params() instead of a branch link. This requires a branch back to save_boot_params_ret so adjust the users to deal with this. For exynos just drop the function since it doesn't do anything. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
OpenPOWER on IntegriCloud