diff options
Diffstat (limited to 'include/configs/ti_armv7_common.h')
| -rw-r--r-- | include/configs/ti_armv7_common.h | 34 |
1 files changed, 31 insertions, 3 deletions
diff --git a/include/configs/ti_armv7_common.h b/include/configs/ti_armv7_common.h index 69d69a5421..485427276a 100644 --- a/include/configs/ti_armv7_common.h +++ b/include/configs/ti_armv7_common.h @@ -20,6 +20,7 @@ /* Common define for many platforms. */ #define CONFIG_OMAP #define CONFIG_OMAP_COMMON +#define CONFIG_SYS_GENERIC_BOARD /* * We typically do not contain NOR flash. In the cases where we do, we @@ -36,8 +37,28 @@ /* * Our DDR memory always starts at 0x80000000 and U-Boot shall have * relocated itself to higher in memory by the time this value is used. + * However, set this to a 32MB offset to allow for easier Linux kernel + * booting as the default is often used as the kernel load address. */ -#define CONFIG_SYS_LOAD_ADDR 0x80000000 +#define CONFIG_SYS_LOAD_ADDR 0x82000000 + +/* + * We setup defaults based on constraints from the Linux kernel, which should + * also be safe elsewhere. We have the default load at 32MB into DDR (for + * the kernel), FDT above 128MB (the maximum location for the end of the + * kernel), and the ramdisk 512KB above that (allowing for hopefully never + * seen large trees). We say all of this must be within the first 256MB + * as that will normally be within the kernel lowmem and thus visible via + * bootm_size and we only run on platforms with 256MB or more of memory. + */ +#define DEFAULT_LINUX_BOOT_ENV \ + "loadaddr=0x82000000\0" \ + "kernel_addr_r=0x82000000\0" \ + "fdtaddr=0x88000000\0" \ + "fdt_addr_r=0x88000000\0" \ + "rdaddr=0x88080000\0" \ + "ramdisk_addr_r=0x88080000\0" \ + "bootm_size=0x10000000\0" /* * Default to a quick boot delay. @@ -90,7 +111,9 @@ */ #ifdef CONFIG_NAND #define CONFIG_NAND_OMAP_GPMC +#ifndef CONFIG_SYS_NAND_BASE #define CONFIG_SYS_NAND_BASE 0x8000000 +#endif #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_CMD_NAND #endif @@ -188,12 +211,18 @@ * We have the SPL malloc pool at the end of the BSS area. */ #define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR +#ifndef CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_TEXT_BASE 0x80800000 +#endif +#ifndef CONFIG_SPL_BSS_START_ADDR #define CONFIG_SPL_BSS_START_ADDR 0x80a00000 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ +#endif +#ifndef CONFIG_SYS_SPL_MALLOC_START #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ CONFIG_SPL_BSS_MAX_SIZE) #define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN +#endif /* RAW SD card / eMMC locations. */ #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ @@ -204,8 +233,6 @@ #define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img" #ifdef CONFIG_SPL_OS_BOOT -#define CONFIG_SYS_SPL_ARGS_ADDR 0x80F80000 - /* FAT */ #define CONFIG_SPL_FAT_LOAD_KERNEL_NAME "uImage" #define CONFIG_SPL_FAT_LOAD_ARGS_NAME "args" @@ -245,6 +272,7 @@ #define CONFIG_SPL_NAND_BASE #define CONFIG_SPL_NAND_DRIVERS #define CONFIG_SPL_NAND_ECC +#define CONFIG_SPL_MTD_SUPPORT #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 #endif |
