diff options
Diffstat (limited to 'include/configs/NETVIA.h')
| -rw-r--r-- | include/configs/NETVIA.h | 435 |
1 files changed, 0 insertions, 435 deletions
diff --git a/include/configs/NETVIA.h b/include/configs/NETVIA.h deleted file mode 100644 index 4a0fa9e119..0000000000 --- a/include/configs/NETVIA.h +++ /dev/null @@ -1,435 +0,0 @@ -/* - * (C) Copyright 2000-2010 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * Pantelis Antoniou, Intracom S.A., panto@intracom.gr - * U-Boot port on NetVia board - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC850 1 /* This is a MPC850 CPU */ -#define CONFIG_NETVIA 1 /* ...on a NetVia board */ - -#define CONFIG_SYS_TEXT_BASE 0x40000000 - -#if !defined(CONFIG_NETVIA_VERSION) || CONFIG_NETVIA_VERSION == 1 -#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ -#undef CONFIG_8xx_CONS_SMC2 -#undef CONFIG_8xx_CONS_NONE -#else -#define CONFIG_8xx_CONS_NONE -#define CONFIG_MAX3100_SERIAL -#endif - -#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ - -#define CONFIG_XIN 10000000 -#define CONFIG_8xx_GCLK_FREQ 80000000 - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#undef CONFIG_CLOCKS_IN_MHZ /* clocks NOT passsed to Linux in MHz */ - -#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" - -#undef CONFIG_BOOTARGS -#define CONFIG_BOOTCOMMAND \ - "tftpboot; " \ - "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \ - "bootm" - -#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#define CONFIG_STATUS_LED 1 /* Status LED enabled */ - -#if defined(CONFIG_NETVIA_VERSION) && CONFIG_NETVIA_VERSION >= 2 -#define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */ -#endif - -#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_NISDOMAIN - - -#undef CONFIG_MAC_PARTITION -#undef CONFIG_DOS_PARTITION - -#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_PING - -#if defined(CONFIG_NETVIA_VERSION) && CONFIG_NETVIA_VERSION >= 2 -/* #define CONFIG_CMD_NAND */ /* disabled */ -#endif - - -#define CONFIG_BOARD_EARLY_INIT_F 1 -#define CONFIG_MISC_INIT_R - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0300000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0700000 /* 3 ... 7 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xFF000000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x3000 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0x40000000 -#if defined(DEBUG) -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#else -#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#endif -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SECT_SIZE 0x10000 - -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x60000) -#define CONFIG_ENV_SIZE 0x4000 - -#define CONFIG_ENV_ADDR_REDUND (CONFIG_SYS_FLASH_BASE + 0x70000) -#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - * PCMCIA config., multi-function pin tri-state - */ -#ifndef CONFIG_CAN_DRIVER -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC) -#else /* we must activate GPL5 in the SIUMCR for CAN */ -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC) -#endif /* CONFIG_CAN_DRIVER */ - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) - -/*----------------------------------------------------------------------- - * RTCSC - Real-Time Clock Status and Control Register 11-27 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 - *----------------------------------------------------------------------- - * Reset PLL lock status sticky bit, timer expired status bit and timer - * interrupt status bit - * - * - *----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ - -#define SCCR_MASK SCCR_EBDF11 - -#if CONFIG_8xx_GCLK_FREQ == 50000000 - -#define CONFIG_SYS_PLPRCR ( ((5 - 1) << PLPRCR_MF_SHIFT) | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) -#define CONFIG_SYS_SCCR (SCCR_TBS | \ - SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ - SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ - SCCR_DFALCD00) - -#elif CONFIG_8xx_GCLK_FREQ == 80000000 - -#define CONFIG_SYS_PLPRCR ( ((8 - 1) << PLPRCR_MF_SHIFT) | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) -#define CONFIG_SYS_SCCR (SCCR_TBS | \ - SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ - SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ - SCCR_DFALCD00 | SCCR_EBDF01) - -#endif - -/*----------------------------------------------------------------------- - * - *----------------------------------------------------------------------- - * - */ -/*#define CONFIG_SYS_DER 0x2002000F*/ -#define CONFIG_SYS_DER 0 - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ - -#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ - -/* used to re-map FLASH both when starting from SRAM or FLASH: - * restrict access enough to keep SRAM working (if any) - * but not too much to meddle with FLASH accesses - */ -#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ -#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ - -/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */ -#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_BI | OR_SCY_5_CLK | OR_TRLX) - -#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V ) - -/* - * BR3 and OR3 (SDRAM) - * - */ -#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank #0 */ -#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */ - -/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ -#define CONFIG_SYS_OR_TIMING_SDRAM (OR_CSNT_SAM | OR_G5LS) - -#define CONFIG_SYS_OR3_PRELIM ((0xFFFFFFFFLU & ~(SDRAM_MAX_SIZE - 1)) | CONFIG_SYS_OR_TIMING_SDRAM) -#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_PS_32 | BR_V) - -/* - * Memory Periodic Timer Prescaler - */ - -/* periodic timer for refresh */ -#define CONFIG_SYS_MAMR_PTA 208 - -/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ -#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ - -/* - * MAMR settings for SDRAM - */ - -/* 9 column SDRAM */ -#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ - MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) - -/* Ethernet at SCC2 */ -#define CONFIG_SCC2_ENET - -/****************************************************************/ - -#define DSP_SIZE 0x00010000 /* 64K */ -#define FPGA_SIZE 0x00010000 /* 64K */ - -#define DSP0_BASE 0xF1000000 -#define DSP1_BASE (DSP0_BASE + DSP_SIZE) -#define FPGA_BASE (DSP1_BASE + DSP_SIZE) - -#if defined(CONFIG_NETVIA_VERSION) && CONFIG_NETVIA_VERSION >= 2 - -#define ER_SIZE 0x00010000 /* 64K */ -#define ER_BASE (FPGA_BASE + FPGA_SIZE) - -#define NAND_SIZE 0x00010000 /* 64K */ -#define NAND_BASE (ER_BASE + ER_SIZE) - -#endif - -/****************************************************************/ - -#if defined(CONFIG_NETVIA_VERSION) && CONFIG_NETVIA_VERSION >= 2 - -#define STATUS_LED_BIT 0x00000001 /* bit 31 */ -#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -#define STATUS_LED_STATE STATUS_LED_BLINKING - -#define STATUS_LED_BIT1 0x00000002 /* bit 30 */ -#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2) -#define STATUS_LED_STATE1 STATUS_LED_OFF - -#define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */ -#define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ - -#endif - - -/*****************************************************************************/ - -#ifndef __ASSEMBLY__ - -#if defined(CONFIG_NETVIA_VERSION) && CONFIG_NETVIA_VERSION >= 2 - -/* LEDs */ - -/* last value written to the external register; we cannot read back */ -extern unsigned int last_er_val; - -/* led_id_t is unsigned long mask */ -typedef unsigned int led_id_t; - -static inline void __led_init(led_id_t mask, int state) -{ - unsigned int new_er_val; - - if (state) - new_er_val = last_er_val & ~mask; - else - new_er_val = last_er_val | mask; - - *(volatile unsigned int *)ER_BASE = new_er_val; - last_er_val = new_er_val; -} - -static inline void __led_toggle(led_id_t mask) -{ - unsigned int new_er_val; - - new_er_val = last_er_val ^ mask; - *(volatile unsigned int *)ER_BASE = new_er_val; - last_er_val = new_er_val; -} - -static inline void __led_set(led_id_t mask, int state) -{ - unsigned int new_er_val; - - if (state) - new_er_val = last_er_val & ~mask; - else - new_er_val = last_er_val | mask; - - *(volatile unsigned int *)ER_BASE = new_er_val; - last_er_val = new_er_val; -} - -/* MAX3100 console */ -#define MAX3100_SPI_RXD_PORT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat) -#define MAX3100_SPI_RXD_BIT 0x00000008 - -#define MAX3100_SPI_TXD_PORT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat) -#define MAX3100_SPI_TXD_BIT 0x00000004 - -#define MAX3100_SPI_CLK_PORT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat) -#define MAX3100_SPI_CLK_BIT 0x00000002 - -#define MAX3100_CS_PORT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) -#define MAX3100_CS_BIT 0x0010 - -#endif - -#endif - -/*************************************************************************************************/ - -#endif /* __CONFIG_H */ |
