diff options
Diffstat (limited to 'include/configs/ELPPC.h')
| -rw-r--r-- | include/configs/ELPPC.h | 337 |
1 files changed, 0 insertions, 337 deletions
diff --git a/include/configs/ELPPC.h b/include/configs/ELPPC.h deleted file mode 100644 index debfc3697e..0000000000 --- a/include/configs/ELPPC.h +++ /dev/null @@ -1,337 +0,0 @@ -/* - * (C) Copyright 2002 ELTEC Elektronik AG - * Frank Gottschling <fgottschling@eltec.de> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define GTREGREAD(x) 0xffffffff /* needed for debug */ - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 - -/* these hardware addresses are pretty bogus, please change them to - suit your needs */ - -/* first ethernet */ -#define CONFIG_ETHADDR 00:00:5b:ee:de:ad - -#define CONFIG_IPADDR 192.168.0.105 -#define CONFIG_SERVERIP 192.168.0.100 - -#define CONFIG_ELPPC 1 /* this is an BAB740/BAB750 board */ - -#define CONFIG_BAUDRATE 9600 /* console baudrate */ - -#undef CONFIG_WATCHDOG - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_ZERO_BOOTDELAY_CHECK - -#undef CONFIG_BOOTARGS -#define CONFIG_BOOTCOMMAND \ - "bootp 1000000; " \ - "setenv bootargs root=ramfs console=ttyS00,9600 " \ - "ip=${ipaddr}:${serverip}:${rootpath}:${gatewayip}:" \ - "${netmask}:${hostname}:eth0:none; " \ - "bootm" - -#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate changes */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH - -#define CONFIG_BOOTP_BOOTFILESIZE - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_PCI -#define CONFIG_CMD_JFFS2 - - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -/* - * choose between COM1 and COM2 as serial console - */ -#define CONFIG_CONS_INDEX 1 - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x04000000 /* 0 ... 64 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */ - -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -#define CONFIG_SYS_BOARD_ASM_INIT -#define CONFIG_MISC_INIT_R - -/* - * Address mapping scheme for the MPC107 mem controller is mapping B (CHRP) - */ -#undef CONFIG_SYS_ADDRESS_MAP_A - -#define CONFIG_SYS_PCI_MEMORY_BUS 0x00000000 -#define CONFIG_SYS_PCI_MEMORY_PHYS 0x00000000 -#define CONFIG_SYS_PCI_MEMORY_SIZE 0x40000000 - -#define CONFIG_SYS_PCI_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCI_MEM_PHYS 0x80000000 -#define CONFIG_SYS_PCI_MEM_SIZE 0x7d000000 - -#define CONFIG_SYS_ISA_MEM_BUS 0x00000000 -#define CONFIG_SYS_ISA_MEM_PHYS 0xfd000000 -#define CONFIG_SYS_ISA_MEM_SIZE 0x01000000 - -#define CONFIG_SYS_PCI_IO_BUS 0x00800000 -#define CONFIG_SYS_PCI_IO_PHYS 0xfe800000 -#define CONFIG_SYS_PCI_IO_SIZE 0x00400000 - -#define CONFIG_SYS_ISA_IO_BUS 0x00000000 -#define CONFIG_SYS_ISA_IO_PHYS 0xfe000000 -#define CONFIG_SYS_ISA_IO_SIZE 0x00800000 - -/* driver defines FDC,IDE,... */ -#define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_ISA_IO_PHYS -#define CONFIG_SYS_ISA_IO CONFIG_SYS_ISA_IO_PHYS -#define CONFIG_SYS_60X_PCI_IO_OFFSET CONFIG_SYS_ISA_IO_PHYS - -/* - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -#define CONFIG_SYS_USR_LED_BASE 0x78000000 -#define CONFIG_SYS_NVRAM_BASE 0xff000000 -#define CONFIG_SYS_UART_BASE 0xff400000 -#define CONFIG_SYS_FLASH_BASE 0xfff00000 - -#define MPC107_EUMB_ADDR 0xfce00000 -#define MPC107_EUMB_PI 0xfce41090 -#define MPC107_EUMB_GCR 0xfce41020 -#define MPC107_EUMB_IACKR 0xfce600a0 -#define MPC107_I2C_ADDR 0xfce03000 - -/* - * Definitions for initial stack pointer and data area - */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x00fd0000 /* above the memtest region */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* - * Flash mapping/organization on the MPC10x. - */ -#define FLASH_BASE0_PRELIM 0xff800000 -#define FLASH_BASE1_PRELIM 0xffc00000 - -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -/* - * JFFS2 partitions - * - */ -/* No command line, one static partition, whole device */ -#undef CONFIG_CMD_MTDPARTS -#define CONFIG_JFFS2_DEV "nor0" -#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF -#define CONFIG_JFFS2_PART_OFFSET 0x00000000 - -/* mtdparts command line support */ -/* Note: fake mtd_id used, no linux mtd map file */ -/* -#define CONFIG_CMD_MTDPARTS -#define MTDIDS_DEFAULT "nor0=elppc-0,nor1=elppc-1" -#define MTDPARTS_DEFAULT "mtdparts=elppc-0:-(jffs2),elppc-1:-(user)" -*/ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN 0x40000 /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN 0x20000 /* Reserve 128 kB for malloc() */ -#undef CONFIG_SYS_MEMTEST - -/* - * Environment settings - */ -#define CONFIG_ENV_OVERWRITE -#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ -#define CONFIG_SYS_NVRAM_SIZE 0x800 /* NVRAM size (2kB) */ -#define CONFIG_ENV_SIZE 0x400 /* Size of Environment vars (1kB) */ -#define CONFIG_ENV_ADDR 0x0 -#define CONFIG_ENV_MAP_ADRS 0xff000000 -#define CONFIG_SYS_NV_SROM_COPY_ADDR (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE) -#define CONFIG_SYS_NVRAM_ACCESS_ROUTINE /* only byte accsess alowed */ -#define CONFIG_SYS_SROM_SIZE 0x100 /* shadow of revision info is in nvram */ - -/* - * Serial devices - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK 24000000 -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_UART_BASE + 0) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_UART_BASE + 8) - -/* - * PCI stuff - */ -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_PNP /* pci plug-and-play */ -#define CONFIG_PCI_HOST PCI_HOST_AUTO -#undef CONFIG_PCI_SCAN_SHOW - -/* - * Optional Video console (graphic: SMI LynxEM) - */ -#define CONFIG_VIDEO -#define CONFIG_CFB_CONSOLE -#define VIDEO_KBD_INIT_FCT (simple_strtol (getenv("console"), NULL, 10)) -#define VIDEO_TSTC_FCT serial_stub_tstc -#define VIDEO_GETC_FCT serial_stub_getc - -#define CONFIG_VIDEO_SMI_LYNXEM -#define CONFIG_VIDEO_LOGO -#define CONFIG_CONSOLE_EXTRA_INFO - -/* - * Initial BATs - */ -#if 1 - -#define CONFIG_SYS_IBAT0L 0 -#define CONFIG_SYS_IBAT0U 0 -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT1U - -#define CONFIG_SYS_IBAT1L 0 -#define CONFIG_SYS_IBAT1U 0 -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U - -#define CONFIG_SYS_IBAT2L 0 -#define CONFIG_SYS_IBAT2U 0 -#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U - -#define CONFIG_SYS_IBAT3L 0 -#define CONFIG_SYS_IBAT3U 0 -#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -#else - -/* SDRAM */ -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_RW) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT1U - -/* address range for flashes */ -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_FLASH_BASE | BATL_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT1U (CONFIG_SYS_FLASH_BASE | BATU_BL_16M | BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U - -/* ISA IO space */ -#define CONFIG_SYS_IBAT2L (CONFIG_SYS_ISA_IO | BATL_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT2U (CONFIG_SYS_ISA_IO | BATU_BL_16M | BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U - -/* ISA memory space */ -#define CONFIG_SYS_IBAT3L (CONFIG_SYS_ISA_MEM | BATL_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT3U (CONFIG_SYS_ISA_MEM | BATU_BL_16M | BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -#endif - -/* - * Speed settings are board specific - */ -#define CONFIG_SYS_BUS_CLK 100000000 -#define CONFIG_SYS_CPU_CLK 400000000 - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * L2CR setup -- make sure this is right for your board! - * look in include/74xx_7xx.h for the defines used here - */ - -#define CONFIG_SYS_L2 - -#if 1 -#define L2_INIT 0 /* cpu 750 CXe*/ -#else -#define L2_INIT (L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \ - L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT) -#endif -#define L2_ENABLE (L2_INIT | L2CR_L2E) - -#define CONFIG_EEPRO100 -#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ -#define CONFIG_EEPRO100_SROM_WRITE - -#endif /* __CONFIG_H */ |
