diff options
Diffstat (limited to 'drivers/net/3c589.h')
| -rw-r--r-- | drivers/net/3c589.h | 435 |
1 files changed, 0 insertions, 435 deletions
diff --git a/drivers/net/3c589.h b/drivers/net/3c589.h deleted file mode 100644 index 8f8cf5be1d..0000000000 --- a/drivers/net/3c589.h +++ /dev/null @@ -1,435 +0,0 @@ -/* - * Copyright (c) 1993 Herb Peyerl (hpeyerl@novatel.ca) All rights reserved. - * - * Redistribution and use in source and binary forms, with or without - * modification, are permitted provided that the following conditions are - * met: 1. Redistributions of source code must retain the above copyright - * notice, this list of conditions and the following disclaimer. 2. The name - * of the author may not be used to endorse or promote products derived from - * this software without specific prior written permission - * - * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO - * EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, - * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED - * TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR - * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF - * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING - * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS - * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - October 2, 1994 - - Modified by: Andres Vega Garcia - - INRIA - Sophia Antipolis, France - e-mail: avega@sophia.inria.fr - finger: avega@pax.inria.fr - - */ - -/* - * Created from if_epreg.h by Fred Gray (fgray@rice.edu) to support the - * 3c590 family. - */ - -/* - * Modified by Shusuke Nisiyama <shu@athena.qe.eng.hokudai.ac.jp> - * for etherboot - * Mar. 14, 2000 -*/ - -/* - * Ethernet software status per interface. - */ - -/* - * Some global constants - */ - -#define TX_INIT_RATE 16 -#define TX_INIT_MAX_RATE 64 -#define RX_INIT_LATENCY 64 -#define RX_INIT_EARLY_THRESH 64 -#define MIN_RX_EARLY_THRESHF 16 /* not less than ether_header */ -#define MIN_RX_EARLY_THRESHL 4 - -#define EEPROMSIZE 0x40 -#define MAX_EEPROMBUSY 1000 -#define VX_LAST_TAG 0xd7 -#define VX_MAX_BOARDS 16 -#define VX_ID_PORT 0x100 - -/* - * some macros to acces long named fields - */ -#define BASE (EL_BASE_ADDR) - -/* - * Commands to read/write EEPROM trough EEPROM command register (Window 0, - * Offset 0xa) - */ -#define EEPROM_CMD_RD 0x0080 /* Read: Address required (5 bits) */ -#define EEPROM_CMD_WR 0x0040 /* Write: Address required (5 bits) */ -#define EEPROM_CMD_ERASE 0x00c0 /* Erase: Address required (5 bits) */ -#define EEPROM_CMD_EWEN 0x0030 /* Erase/Write Enable: No data required */ - -#define EEPROM_BUSY (1<<15) - -/* - * Some short functions, worth to let them be a macro - */ - -/************************************************************************** - * * - * These define the EEPROM data structure. They are used in the probe - * function to verify the existence of the adapter after having sent - * the ID_Sequence. - * - * There are others but only the ones we use are defined here. - * - **************************************************************************/ - -#define EEPROM_NODE_ADDR_0 0x0 /* Word */ -#define EEPROM_NODE_ADDR_1 0x1 /* Word */ -#define EEPROM_NODE_ADDR_2 0x2 /* Word */ -#define EEPROM_PROD_ID 0x3 /* 0x9[0-f]50 */ -#define EEPROM_MFG_ID 0x7 /* 0x6d50 */ -#define EEPROM_ADDR_CFG 0x8 /* Base addr */ -#define EEPROM_RESOURCE_CFG 0x9 /* IRQ. Bits 12-15 */ -#define EEPROM_OEM_ADDR_0 0xa /* Word */ -#define EEPROM_OEM_ADDR_1 0xb /* Word */ -#define EEPROM_OEM_ADDR_2 0xc /* Word */ -#define EEPROM_SOFT_INFO_2 0xf /* Software information 2 */ - -#define NO_RX_OVN_ANOMALY (1<<5) - -/************************************************************************** - * * - * These are the registers for the 3Com 3c509 and their bit patterns when * - * applicable. They have been taken out the the "EtherLink III Parallel * - * Tasking EISA and ISA Technical Reference" "Beta Draft 10/30/92" manual * - * from 3com. * - * * - **************************************************************************/ - -#define VX_COMMAND 0x0e /* Write. BASE+0x0e is always a - * command reg. */ -#define VX_STATUS 0x0e /* Read. BASE+0x0e is always status - * reg. */ -#define VX_WINDOW 0x0f /* Read. BASE+0x0f is always window - * reg. */ -/* - * Window 0 registers. Setup. - */ -/* Write */ -#define VX_W0_EEPROM_DATA 0x0c -#define VX_W0_EEPROM_COMMAND 0x0a -#define VX_W0_RESOURCE_CFG 0x08 -#define VX_W0_ADDRESS_CFG 0x06 -#define VX_W0_CONFIG_CTRL 0x04 - /* Read */ -#define VX_W0_PRODUCT_ID 0x02 -#define VX_W0_MFG_ID 0x00 - - -/* - * Window 1 registers. Operating Set. - */ -/* Write */ -#define VX_W1_TX_PIO_WR_2 0x02 -#define VX_W1_TX_PIO_WR_1 0x00 -/* Read */ -#define VX_W1_FREE_TX 0x0c -#define VX_W1_TX_STATUS 0x0b /* byte */ -#define VX_W1_TIMER 0x0a /* byte */ -#define VX_W1_RX_STATUS 0x08 -#define VX_W1_RX_PIO_RD_2 0x02 -#define VX_W1_RX_PIO_RD_1 0x00 - -/* - * Window 2 registers. Station Address Setup/Read - */ -/* Read/Write */ -#define VX_W2_ADDR_5 0x05 -#define VX_W2_ADDR_4 0x04 -#define VX_W2_ADDR_3 0x03 -#define VX_W2_ADDR_2 0x02 -#define VX_W2_ADDR_1 0x01 -#define VX_W2_ADDR_0 0x00 - -/* - * Window 3 registers. FIFO Management. - */ -/* Read */ -#define VX_W3_INTERNAL_CFG 0x00 -#define VX_W3_RESET_OPT 0x08 -#define VX_W3_FREE_TX 0x0c -#define VX_W3_FREE_RX 0x0a - -/* - * Window 4 registers. Diagnostics. - */ -/* Read/Write */ -#define VX_W4_MEDIA_TYPE 0x0a -#define VX_W4_CTRLR_STATUS 0x08 -#define VX_W4_NET_DIAG 0x06 -#define VX_W4_FIFO_DIAG 0x04 -#define VX_W4_HOST_DIAG 0x02 -#define VX_W4_TX_DIAG 0x00 - -/* - * Window 5 Registers. Results and Internal status. - */ -/* Read */ -#define VX_W5_READ_0_MASK 0x0c -#define VX_W5_INTR_MASK 0x0a -#define VX_W5_RX_FILTER 0x08 -#define VX_W5_RX_EARLY_THRESH 0x06 -#define VX_W5_TX_AVAIL_THRESH 0x02 -#define VX_W5_TX_START_THRESH 0x00 - -/* - * Window 6 registers. Statistics. - */ -/* Read/Write */ -#define TX_TOTAL_OK 0x0c -#define RX_TOTAL_OK 0x0a -#define TX_DEFERRALS 0x08 -#define RX_FRAMES_OK 0x07 -#define TX_FRAMES_OK 0x06 -#define RX_OVERRUNS 0x05 -#define TX_COLLISIONS 0x04 -#define TX_AFTER_1_COLLISION 0x03 -#define TX_AFTER_X_COLLISIONS 0x02 -#define TX_NO_SQE 0x01 -#define TX_CD_LOST 0x00 - -/**************************************** - * - * Register definitions. - * - ****************************************/ - -/* - * Command register. All windows. - * - * 16 bit register. - * 15-11: 5-bit code for command to be executed. - * 10-0: 11-bit arg if any. For commands with no args; - * this can be set to anything. - */ -#define GLOBAL_RESET (unsigned short) 0x0000 /* Wait at least 1ms - * after issuing */ -#define WINDOW_SELECT (unsigned short) (0x1<<11) -#define START_TRANSCEIVER (unsigned short) (0x2<<11) /* Read ADDR_CFG reg to - * determine whether - * this is needed. If - * so; wait 800 uSec - * before using trans- - * ceiver. */ -#define RX_DISABLE (unsigned short) (0x3<<11) /* state disabled on - * power-up */ -#define RX_ENABLE (unsigned short) (0x4<<11) -#define RX_RESET (unsigned short) (0x5<<11) -#define RX_DISCARD_TOP_PACK (unsigned short) (0x8<<11) -#define TX_ENABLE (unsigned short) (0x9<<11) -#define TX_DISABLE (unsigned short) (0xa<<11) -#define TX_RESET (unsigned short) (0xb<<11) -#define REQ_INTR (unsigned short) (0xc<<11) -/* - * The following C_* acknowledge the various interrupts. Some of them don't - * do anything. See the manual. - */ -#define ACK_INTR (unsigned short) (0x6800) -# define C_INTR_LATCH (unsigned short) (ACK_INTR|0x1) -# define C_CARD_FAILURE (unsigned short) (ACK_INTR|0x2) -# define C_TX_COMPLETE (unsigned short) (ACK_INTR|0x4) -# define C_TX_AVAIL (unsigned short) (ACK_INTR|0x8) -# define C_RX_COMPLETE (unsigned short) (ACK_INTR|0x10) -# define C_RX_EARLY (unsigned short) (ACK_INTR|0x20) -# define C_INT_RQD (unsigned short) (ACK_INTR|0x40) -# define C_UPD_STATS (unsigned short) (ACK_INTR|0x80) -#define SET_INTR_MASK (unsigned short) (0xe<<11) -#define SET_RD_0_MASK (unsigned short) (0xf<<11) -#define SET_RX_FILTER (unsigned short) (0x10<<11) -# define FIL_INDIVIDUAL (unsigned short) (0x1) -# define FIL_MULTICAST (unsigned short) (0x02) -# define FIL_BRDCST (unsigned short) (0x04) -# define FIL_PROMISC (unsigned short) (0x08) -#define SET_RX_EARLY_THRESH (unsigned short) (0x11<<11) -#define SET_TX_AVAIL_THRESH (unsigned short) (0x12<<11) -#define SET_TX_START_THRESH (unsigned short) (0x13<<11) -#define STATS_ENABLE (unsigned short) (0x15<<11) -#define STATS_DISABLE (unsigned short) (0x16<<11) -#define STOP_TRANSCEIVER (unsigned short) (0x17<<11) - -/* - * Status register. All windows. - * - * 15-13: Window number(0-7). - * 12: Command_in_progress. - * 11: reserved. - * 10: reserved. - * 9: reserved. - * 8: reserved. - * 7: Update Statistics. - * 6: Interrupt Requested. - * 5: RX Early. - * 4: RX Complete. - * 3: TX Available. - * 2: TX Complete. - * 1: Adapter Failure. - * 0: Interrupt Latch. - */ -#define S_INTR_LATCH (unsigned short) (0x1) -#define S_CARD_FAILURE (unsigned short) (0x2) -#define S_TX_COMPLETE (unsigned short) (0x4) -#define S_TX_AVAIL (unsigned short) (0x8) -#define S_RX_COMPLETE (unsigned short) (0x10) -#define S_RX_EARLY (unsigned short) (0x20) -#define S_INT_RQD (unsigned short) (0x40) -#define S_UPD_STATS (unsigned short) (0x80) -#define S_COMMAND_IN_PROGRESS (unsigned short) (0x1000) - -#define VX_BUSY_WAIT while (inw(BASE + VX_STATUS) & S_COMMAND_IN_PROGRESS) - -/* Address Config. Register. - * Window 0/Port 06 - */ - -#define ACF_CONNECTOR_BITS 14 -#define ACF_CONNECTOR_UTP 0 -#define ACF_CONNECTOR_AUI 1 -#define ACF_CONNECTOR_BNC 3 - -#define INTERNAL_CONNECTOR_BITS 20 -#define INTERNAL_CONNECTOR_MASK 0x01700000 - -/* - * FIFO Registers. RX Status. - * - * 15: Incomplete or FIFO empty. - * 14: 1: Error in RX Packet 0: Incomplete or no error. - * 13-11: Type of error. - * 1000 = Overrun. - * 1011 = Run Packet Error. - * 1100 = Alignment Error. - * 1101 = CRC Error. - * 1001 = Oversize Packet Error (>1514 bytes) - * 0010 = Dribble Bits. - * (all other error codes, no errors.) - * - * 10-0: RX Bytes (0-1514) - */ -#define ERR_INCOMPLETE (unsigned short) (0x8000) -#define ERR_RX (unsigned short) (0x4000) -#define ERR_MASK (unsigned short) (0x7800) -#define ERR_OVERRUN (unsigned short) (0x4000) -#define ERR_RUNT (unsigned short) (0x5800) -#define ERR_ALIGNMENT (unsigned short) (0x6000) -#define ERR_CRC (unsigned short) (0x6800) -#define ERR_OVERSIZE (unsigned short) (0x4800) -#define ERR_DRIBBLE (unsigned short) (0x1000) - -/* - * TX Status. - * - * Reports the transmit status of a completed transmission. Writing this - * register pops the transmit completion stack. - * - * Window 1/Port 0x0b. - * - * 7: Complete - * 6: Interrupt on successful transmission requested. - * 5: Jabber Error (TP Only, TX Reset required. ) - * 4: Underrun (TX Reset required. ) - * 3: Maximum Collisions. - * 2: TX Status Overflow. - * 1-0: Undefined. - * - */ -#define TXS_COMPLETE 0x80 -#define TXS_INTR_REQ 0x40 -#define TXS_JABBER 0x20 -#define TXS_UNDERRUN 0x10 -#define TXS_MAX_COLLISION 0x8 -#define TXS_STATUS_OVERFLOW 0x4 - -#define RS_AUI (1<<5) -#define RS_BNC (1<<4) -#define RS_UTP (1<<3) -#define RS_T4 (1<<0) -#define RS_TX (1<<1) -#define RS_FX (1<<2) -#define RS_MII (1<<6) - - -/* - * FIFO Status (Window 4) - * - * Supports FIFO diagnostics - * - * Window 4/Port 0x04.1 - * - * 15: 1=RX receiving (RO). Set when a packet is being received - * into the RX FIFO. - * 14: Reserved - * 13: 1=RX underrun (RO). Generates Adapter Failure interrupt. - * Requires RX Reset or Global Reset command to recover. - * It is generated when you read past the end of a packet - - * reading past what has been received so far will give bad - * data. - * 12: 1=RX status overrun (RO). Set when there are already 8 - * packets in the RX FIFO. While this bit is set, no additional - * packets are received. Requires no action on the part of - * the host. The condition is cleared once a packet has been - * read out of the RX FIFO. - * 11: 1=RX overrun (RO). Set when the RX FIFO is full (there - * may not be an overrun packet yet). While this bit is set, - * no additional packets will be received (some additional - * bytes can still be pending between the wire and the RX - * FIFO). Requires no action on the part of the host. The - * condition is cleared once a few bytes have been read out - * from the RX FIFO. - * 10: 1=TX overrun (RO). Generates adapter failure interrupt. - * Requires TX Reset or Global Reset command to recover. - * Disables Transmitter. - * 9-8: Unassigned. - * 7-0: Built in self test bits for the RX and TX FIFO's. - */ -#define FIFOS_RX_RECEIVING (unsigned short) 0x8000 -#define FIFOS_RX_UNDERRUN (unsigned short) 0x2000 -#define FIFOS_RX_STATUS_OVERRUN (unsigned short) 0x1000 -#define FIFOS_RX_OVERRUN (unsigned short) 0x0800 -#define FIFOS_TX_OVERRUN (unsigned short) 0x0400 - -/* - * Misc defines for various things. - */ -#define TAG_ADAPTER 0xd0 -#define ACTIVATE_ADAPTER_TO_CONFIG 0xff -#define ENABLE_DRQ_IRQ 0x0001 -#define MFG_ID 0x506d /* `TCM' */ -#define PROD_ID 0x5090 -#define GO_WINDOW(x) outw(WINDOW_SELECT|(x),BASE+VX_COMMAND) -#define JABBER_GUARD_ENABLE 0x40 -#define LINKBEAT_ENABLE 0x80 -#define ENABLE_UTP (JABBER_GUARD_ENABLE | LINKBEAT_ENABLE) -#define DISABLE_UTP 0x0 -#define RX_BYTES_MASK (unsigned short) (0x07ff) -#define RX_ERROR 0x4000 -#define RX_INCOMPLETE 0x8000 -#define TX_INDICATE 1<<15 -#define is_eeprom_busy(b) (inw((b)+VX_W0_EEPROM_COMMAND)&EEPROM_BUSY) - -#define VX_IOSIZE 0x20 - -#define VX_CONNECTORS 8 - -/* - * Local variables: - * c-basic-offset: 8 - * End: - */ |
