diff options
Diffstat (limited to 'cpu/blackfin/initcode.c')
| -rw-r--r-- | cpu/blackfin/initcode.c | 687 |
1 files changed, 0 insertions, 687 deletions
diff --git a/cpu/blackfin/initcode.c b/cpu/blackfin/initcode.c deleted file mode 100644 index 5f80ad615e..0000000000 --- a/cpu/blackfin/initcode.c +++ /dev/null @@ -1,687 +0,0 @@ -/* - * initcode.c - Initialize the processor. This is usually entails things - * like external memory, voltage regulators, etc... Note that this file - * cannot make any function calls as it may be executed all by itself by - * the Blackfin's bootrom in LDR format. - * - * Copyright (c) 2004-2008 Analog Devices Inc. - * - * Licensed under the GPL-2 or later. - */ - -#define BFIN_IN_INITCODE - -#include <config.h> -#include <asm/blackfin.h> -#include <asm/mach-common/bits/bootrom.h> -#include <asm/mach-common/bits/core.h> -#include <asm/mach-common/bits/ebiu.h> -#include <asm/mach-common/bits/pll.h> -#include <asm/mach-common/bits/uart.h> - -#include "serial.h" - -__attribute__((always_inline)) -static inline void serial_init(void) -{ -#ifdef __ADSPBF54x__ -# ifdef BFIN_BOOT_UART_USE_RTS -# define BFIN_UART_USE_RTS 1 -# else -# define BFIN_UART_USE_RTS 0 -# endif - if (BFIN_UART_USE_RTS && CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_UART) { - size_t i; - - /* force RTS rather than relying on auto RTS */ - bfin_write16(&pUART->mcr, bfin_read16(&pUART->mcr) | FCPOL); - - /* Wait for the line to clear up. We cannot rely on UART - * registers as none of them reflect the status of the RSR. - * Instead, we'll sleep for ~10 bit times at 9600 baud. - * We can precalc things here by assuming boot values for - * PLL rather than loading registers and calculating. - * baud = SCLK / (16 ^ (1 - EDBO) * Divisor) - * EDB0 = 0 - * Divisor = (SCLK / baud) / 16 - * SCLK = baud * 16 * Divisor - * SCLK = (0x14 * CONFIG_CLKIN_HZ) / 5 - * CCLK = (16 * Divisor * 5) * (9600 / 10) - * In reality, this will probably be just about 1 second delay, - * so assuming 9600 baud is OK (both as a very low and too high - * speed as this will buffer things enough). - */ -#define _NUMBITS (10) /* how many bits to delay */ -#define _LOWBAUD (9600) /* low baud rate */ -#define _SCLK ((0x14 * CONFIG_CLKIN_HZ) / 5) /* SCLK based on PLL */ -#define _DIVISOR ((_SCLK / _LOWBAUD) / 16) /* UART DLL/DLH */ -#define _NUMINS (3) /* how many instructions in loop */ -#define _CCLK (((16 * _DIVISOR * 5) * (_LOWBAUD / _NUMBITS)) / _NUMINS) - i = _CCLK; - while (i--) - asm volatile("" : : : "memory"); - } -#endif - - if (BFIN_DEBUG_EARLY_SERIAL) { - int ucen = bfin_read16(&pUART->gctl) & UCEN; - serial_early_init(); - - /* If the UART is off, that means we need to program - * the baud rate ourselves initially. - */ - if (ucen != UCEN) - serial_early_set_baud(CONFIG_BAUDRATE); - } -} - -__attribute__((always_inline)) -static inline void serial_deinit(void) -{ -#ifdef __ADSPBF54x__ - if (BFIN_UART_USE_RTS && CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_UART) { - /* clear forced RTS rather than relying on auto RTS */ - bfin_write16(&pUART->mcr, bfin_read16(&pUART->mcr) & ~FCPOL); - } -#endif -} - -__attribute__((always_inline)) -static inline void serial_putc(char c) -{ - if (!BFIN_DEBUG_EARLY_SERIAL) - return; - - if (c == '\n') - serial_putc('\r'); - - bfin_write16(&pUART->thr, c); - - while (!(bfin_read16(&pUART->lsr) & TEMT)) - continue; -} - - -/* Max SCLK can be 133MHz ... dividing that by (2*4) gives - * us a freq of 16MHz for SPI which should generally be - * slow enough for the slow reads the bootrom uses. - */ -#if !defined(CONFIG_SPI_FLASH_SLOW_READ) && \ - ((defined(__ADSPBF52x__) && __SILICON_REVISION__ >= 2) || \ - (defined(__ADSPBF54x__) && __SILICON_REVISION__ >= 1)) -# define BOOTROM_SUPPORTS_SPI_FAST_READ 1 -#else -# define BOOTROM_SUPPORTS_SPI_FAST_READ 0 -#endif -#ifndef CONFIG_SPI_BAUD_INITBLOCK -# define CONFIG_SPI_BAUD_INITBLOCK (BOOTROM_SUPPORTS_SPI_FAST_READ ? 2 : 4) -#endif -#ifdef SPI0_BAUD -# define bfin_write_SPI_BAUD bfin_write_SPI0_BAUD -#endif - -/* PLL_DIV defines */ -#ifndef CONFIG_PLL_DIV_VAL -# if (CONFIG_CCLK_DIV == 1) -# define CONFIG_CCLK_ACT_DIV CCLK_DIV1 -# elif (CONFIG_CCLK_DIV == 2) -# define CONFIG_CCLK_ACT_DIV CCLK_DIV2 -# elif (CONFIG_CCLK_DIV == 4) -# define CONFIG_CCLK_ACT_DIV CCLK_DIV4 -# elif (CONFIG_CCLK_DIV == 8) -# define CONFIG_CCLK_ACT_DIV CCLK_DIV8 -# else -# define CONFIG_CCLK_ACT_DIV CONFIG_CCLK_DIV_not_defined_properly -# endif -# define CONFIG_PLL_DIV_VAL (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV) -#endif - -#ifndef CONFIG_PLL_LOCKCNT_VAL -# define CONFIG_PLL_LOCKCNT_VAL 0x0300 -#endif - -#ifndef CONFIG_PLL_CTL_VAL -# define CONFIG_PLL_CTL_VAL (SPORT_HYST | (CONFIG_VCO_MULT << 9) | CONFIG_CLKIN_HALF) -#endif - -#ifndef CONFIG_EBIU_RSTCTL_VAL -# define CONFIG_EBIU_RSTCTL_VAL 0 /* only MDDRENABLE is useful */ -#endif -#if ((CONFIG_EBIU_RSTCTL_VAL & 0xFFFFFFC4) != 0) -# error invalid EBIU_RSTCTL value: must not set reserved bits -#endif - -#ifndef CONFIG_EBIU_MBSCTL_VAL -# define CONFIG_EBIU_MBSCTL_VAL 0 -#endif - -#if defined(CONFIG_EBIU_DDRQUE_VAL) && ((CONFIG_EBIU_DDRQUE_VAL & 0xFFFF8000) != 0) -# error invalid EBIU_DDRQUE value: must not set reserved bits -#endif - -/* Make sure our voltage value is sane so we don't blow up! */ -#ifndef CONFIG_VR_CTL_VAL -# define BFIN_CCLK ((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT) / CONFIG_CCLK_DIV) -# if defined(__ADSPBF533__) || defined(__ADSPBF532__) || defined(__ADSPBF531__) -# define CCLK_VLEV_120 400000000 -# define CCLK_VLEV_125 533000000 -# elif defined(__ADSPBF537__) || defined(__ADSPBF536__) || defined(__ADSPBF534__) -# define CCLK_VLEV_120 401000000 -# define CCLK_VLEV_125 401000000 -# elif defined(__ADSPBF561__) -# define CCLK_VLEV_120 300000000 -# define CCLK_VLEV_125 501000000 -# endif -# if BFIN_CCLK < CCLK_VLEV_120 -# define CONFIG_VR_CTL_VLEV VLEV_120 -# elif BFIN_CCLK < CCLK_VLEV_125 -# define CONFIG_VR_CTL_VLEV VLEV_125 -# else -# define CONFIG_VR_CTL_VLEV VLEV_130 -# endif -# if defined(__ADSPBF52x__) /* TBD; use default */ -# undef CONFIG_VR_CTL_VLEV -# define CONFIG_VR_CTL_VLEV VLEV_110 -# elif defined(__ADSPBF54x__) /* TBD; use default */ -# undef CONFIG_VR_CTL_VLEV -# define CONFIG_VR_CTL_VLEV VLEV_120 -# elif defined(__ADSPBF538__) || defined(__ADSPBF539__) /* TBD; use default */ -# undef CONFIG_VR_CTL_VLEV -# define CONFIG_VR_CTL_VLEV VLEV_125 -# endif - -# ifdef CONFIG_BFIN_MAC -# define CONFIG_VR_CTL_CLKBUF CLKBUFOE -# else -# define CONFIG_VR_CTL_CLKBUF 0 -# endif - -# if defined(__ADSPBF52x__) -# define CONFIG_VR_CTL_FREQ FREQ_1000 -# else -# define CONFIG_VR_CTL_FREQ (GAIN_20 | FREQ_1000) -# endif - -# define CONFIG_VR_CTL_VAL (CONFIG_VR_CTL_CLKBUF | CONFIG_VR_CTL_VLEV | CONFIG_VR_CTL_FREQ) -#endif - -/* some parts do not have an on-chip voltage regulator */ -#if defined(__ADSPBF51x__) -# define CONFIG_HAS_VR 0 -# undef CONFIG_VR_CTL_VAL -# define CONFIG_VR_CTL_VAL 0 -#else -# define CONFIG_HAS_VR 1 -#endif - -#if CONFIG_MEM_SIZE -#ifndef EBIU_RSTCTL -/* Blackfin with SDRAM */ -#ifndef CONFIG_EBIU_SDBCTL_VAL -# if CONFIG_MEM_SIZE == 16 -# define CONFIG_EBSZ_VAL EBSZ_16 -# elif CONFIG_MEM_SIZE == 32 -# define CONFIG_EBSZ_VAL EBSZ_32 -# elif CONFIG_MEM_SIZE == 64 -# define CONFIG_EBSZ_VAL EBSZ_64 -# elif CONFIG_MEM_SIZE == 128 -# define CONFIG_EBSZ_VAL EBSZ_128 -# elif CONFIG_MEM_SIZE == 256 -# define CONFIG_EBSZ_VAL EBSZ_256 -# elif CONFIG_MEM_SIZE == 512 -# define CONFIG_EBSZ_VAL EBSZ_512 -# else -# error You need to define CONFIG_EBIU_SDBCTL_VAL or CONFIG_MEM_SIZE -# endif -# if CONFIG_MEM_ADD_WDTH == 8 -# define CONFIG_EBCAW_VAL EBCAW_8 -# elif CONFIG_MEM_ADD_WDTH == 9 -# define CONFIG_EBCAW_VAL EBCAW_9 -# elif CONFIG_MEM_ADD_WDTH == 10 -# define CONFIG_EBCAW_VAL EBCAW_10 -# elif CONFIG_MEM_ADD_WDTH == 11 -# define CONFIG_EBCAW_VAL EBCAW_11 -# else -# error You need to define CONFIG_EBIU_SDBCTL_VAL or CONFIG_MEM_ADD_WDTH -# endif -# define CONFIG_EBIU_SDBCTL_VAL (CONFIG_EBCAW_VAL | CONFIG_EBSZ_VAL | EBE) -#endif -#endif -#endif - -/* Conflicting Column Address Widths Causes SDRAM Errors: - * EB2CAW and EB3CAW must be the same - */ -#if ANOMALY_05000362 -# if ((CONFIG_EBIU_SDBCTL_VAL & 0x30000000) >> 8) != (CONFIG_EBIU_SDBCTL_VAL & 0x00300000) -# error "Anomaly 05000362: EB2CAW and EB3CAW must be the same" -# endif -#endif - -__attribute__((always_inline)) static inline void -program_early_devices(ADI_BOOT_DATA *bs, uint *sdivB, uint *divB, uint *vcoB) -{ - serial_putc('a'); - - /* Save the clock pieces that are used in baud rate calculation */ - if (BFIN_DEBUG_EARLY_SERIAL || CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_UART) { - serial_putc('b'); - *sdivB = bfin_read_PLL_DIV() & 0xf; - *vcoB = (bfin_read_PLL_CTL() >> 9) & 0x3f; - *divB = serial_early_get_div(); - serial_putc('c'); - } - - serial_putc('d'); - -#ifdef CONFIG_HW_WATCHDOG -# ifndef CONFIG_HW_WATCHDOG_TIMEOUT_INITCODE -# define CONFIG_HW_WATCHDOG_TIMEOUT_INITCODE 20000 -# endif - /* Program the watchdog with an initial timeout of ~20 seconds. - * Hopefully that should be long enough to load the u-boot LDR - * (from wherever) and then the common u-boot code can take over. - * In bypass mode, the start.S would have already set a much lower - * timeout, so don't clobber that. - */ - if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_BYPASS) { - serial_putc('e'); - bfin_write_WDOG_CNT(MSEC_TO_SCLK(CONFIG_HW_WATCHDOG_TIMEOUT_INITCODE)); - bfin_write_WDOG_CTL(0); - serial_putc('f'); - } -#endif - - serial_putc('g'); - - /* Blackfin bootroms use the SPI slow read opcode instead of the SPI - * fast read, so we need to slow down the SPI clock a lot more during - * boot. Once we switch over to u-boot's SPI flash driver, we'll - * increase the speed appropriately. - */ - if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) { - serial_putc('h'); - if (BOOTROM_SUPPORTS_SPI_FAST_READ && CONFIG_SPI_BAUD_INITBLOCK < 4) - bs->dFlags |= BFLAG_FASTREAD; - bfin_write_SPI_BAUD(CONFIG_SPI_BAUD_INITBLOCK); - serial_putc('i'); - } - - serial_putc('j'); -} - -__attribute__((always_inline)) static inline bool -maybe_self_refresh(ADI_BOOT_DATA *bs) -{ - serial_putc('a'); - - if (!CONFIG_MEM_SIZE) - return false; - - /* If external memory is enabled, put it into self refresh first. */ -#ifdef EBIU_RSTCTL - if (bfin_read_EBIU_RSTCTL() & DDR_SRESET) { - serial_putc('b'); - bfin_write_EBIU_RSTCTL(bfin_read_EBIU_RSTCTL() | SRREQ); - return true; - } -#else - if (bfin_read_EBIU_SDBCTL() & EBE) { - serial_putc('b'); - bfin_write_EBIU_SDGCTL(bfin_read_EBIU_SDGCTL() | SRFS); - return true; - } -#endif - - serial_putc('c'); - - return false; -} - -__attribute__((always_inline)) static inline u16 -program_clocks(ADI_BOOT_DATA *bs, bool put_into_srfs) -{ - u16 vr_ctl; - - serial_putc('a'); - - vr_ctl = bfin_read_VR_CTL(); - - serial_putc('b'); - - /* If we're entering self refresh, make sure it has happened. */ - if (put_into_srfs) -#ifdef EBIU_RSTCTL - while (!(bfin_read_EBIU_RSTCTL() & SRACK)) -#else - while (!(bfin_read_EBIU_SDSTAT() & SDSRA)) -#endif - continue; - - serial_putc('c'); - - /* With newer bootroms, we use the helper function to set up - * the memory controller. Older bootroms lacks such helpers - * so we do it ourselves. - */ - if (!ANOMALY_05000386) { - serial_putc('d'); - - /* Always programming PLL_LOCKCNT avoids Anomaly 05000430 */ - ADI_SYSCTRL_VALUES memory_settings; - uint32_t actions = SYSCTRL_WRITE | SYSCTRL_PLLCTL | SYSCTRL_PLLDIV | SYSCTRL_LOCKCNT; - if (CONFIG_HAS_VR) { - actions |= SYSCTRL_VRCTL; - if (CONFIG_VR_CTL_VAL & FREQ_MASK) - actions |= SYSCTRL_INTVOLTAGE; - else - actions |= SYSCTRL_EXTVOLTAGE; - memory_settings.uwVrCtl = CONFIG_VR_CTL_VAL; - } else - actions |= SYSCTRL_EXTVOLTAGE; - memory_settings.uwPllCtl = CONFIG_PLL_CTL_VAL; - memory_settings.uwPllDiv = CONFIG_PLL_DIV_VAL; - memory_settings.uwPllLockCnt = CONFIG_PLL_LOCKCNT_VAL; -#if ANOMALY_05000432 - bfin_write_SIC_IWR1(0); -#endif - serial_putc('e'); - bfrom_SysControl(actions, &memory_settings, NULL); - serial_putc('f'); -#if ANOMALY_05000432 - bfin_write_SIC_IWR1(-1); -#endif -#if ANOMALY_05000171 - bfin_write_SICA_IWR0(-1); - bfin_write_SICA_IWR1(-1); -#endif - serial_putc('g'); - } else { - serial_putc('h'); - - /* Disable all peripheral wakeups except for the PLL event. */ -#ifdef SIC_IWR0 - bfin_write_SIC_IWR0(1); - bfin_write_SIC_IWR1(0); -# ifdef SIC_IWR2 - bfin_write_SIC_IWR2(0); -# endif -#elif defined(SICA_IWR0) - bfin_write_SICA_IWR0(1); - bfin_write_SICA_IWR1(0); -#else - bfin_write_SIC_IWR(1); -#endif - - serial_putc('i'); - - /* Always programming PLL_LOCKCNT avoids Anomaly 05000430 */ - bfin_write_PLL_LOCKCNT(CONFIG_PLL_LOCKCNT_VAL); - - serial_putc('j'); - - /* Only reprogram when needed to avoid triggering unnecessary - * PLL relock sequences. - */ - if (vr_ctl != CONFIG_VR_CTL_VAL) { - serial_putc('?'); - bfin_write_VR_CTL(CONFIG_VR_CTL_VAL); - asm("idle;"); - serial_putc('!'); - } - - serial_putc('k'); - - bfin_write_PLL_DIV(CONFIG_PLL_DIV_VAL); - - serial_putc('l'); - - /* Only reprogram when needed to avoid triggering unnecessary - * PLL relock sequences. - */ - if (ANOMALY_05000242 || bfin_read_PLL_CTL() != CONFIG_PLL_CTL_VAL) { - serial_putc('?'); - bfin_write_PLL_CTL(CONFIG_PLL_CTL_VAL); - asm("idle;"); - serial_putc('!'); - } - - serial_putc('m'); - - /* Restore all peripheral wakeups. */ -#ifdef SIC_IWR0 - bfin_write_SIC_IWR0(-1); - bfin_write_SIC_IWR1(-1); -# ifdef SIC_IWR2 - bfin_write_SIC_IWR2(-1); -# endif -#elif defined(SICA_IWR0) - bfin_write_SICA_IWR0(-1); - bfin_write_SICA_IWR1(-1); -#else - bfin_write_SIC_IWR(-1); -#endif - - serial_putc('n'); - } - - serial_putc('o'); - - return vr_ctl; -} - -__attribute__((always_inline)) static inline void -update_serial_clocks(ADI_BOOT_DATA *bs, uint sdivB, uint divB, uint vcoB) -{ - serial_putc('a'); - - /* Since we've changed the SCLK above, we may need to update - * the UART divisors (UART baud rates are based on SCLK). - * Do the division by hand as there are no native instructions - * for dividing which means we'd generate a libgcc reference. - */ - if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_UART) { - serial_putc('b'); - unsigned int sdivR, vcoR; - sdivR = bfin_read_PLL_DIV() & 0xf; - vcoR = (bfin_read_PLL_CTL() >> 9) & 0x3f; - int dividend = sdivB * divB * vcoR; - int divisor = vcoB * sdivR; - unsigned int quotient; - for (quotient = 0; dividend > 0; ++quotient) - dividend -= divisor; - serial_early_put_div(quotient - ANOMALY_05000230); - serial_putc('c'); - } - - serial_putc('d'); -} - -__attribute__((always_inline)) static inline void -program_memory_controller(ADI_BOOT_DATA *bs, bool put_into_srfs) -{ - serial_putc('a'); - - if (!CONFIG_MEM_SIZE) - return; - - serial_putc('b'); - - /* Program the external memory controller before we come out of - * self-refresh. This only works with our SDRAM controller. - */ -#ifndef EBIU_RSTCTL -# ifdef CONFIG_EBIU_SDRRC_VAL - bfin_write_EBIU_SDRRC(CONFIG_EBIU_SDRRC_VAL); -# endif -# ifdef CONFIG_EBIU_SDBCTL_VAL - bfin_write_EBIU_SDBCTL(CONFIG_EBIU_SDBCTL_VAL); -# endif -# ifdef CONFIG_EBIU_SDGCTL_VAL - bfin_write_EBIU_SDGCTL(CONFIG_EBIU_SDGCTL_VAL); -# endif -#endif - - serial_putc('c'); - - /* Now that we've reprogrammed, take things out of self refresh. */ - if (put_into_srfs) -#ifdef EBIU_RSTCTL - bfin_write_EBIU_RSTCTL(bfin_read_EBIU_RSTCTL() & ~(SRREQ)); -#else - bfin_write_EBIU_SDGCTL(bfin_read_EBIU_SDGCTL() & ~(SRFS)); -#endif - - serial_putc('d'); - - /* Our DDR controller sucks and cannot be programmed while in - * self-refresh. So we have to pull it out before programming. - */ -#ifdef EBIU_RSTCTL -# ifdef CONFIG_EBIU_RSTCTL_VAL - bfin_write_EBIU_RSTCTL(bfin_read_EBIU_RSTCTL() | 0x1 /*DDRSRESET*/ | CONFIG_EBIU_RSTCTL_VAL); -# endif -# ifdef CONFIG_EBIU_DDRCTL0_VAL - bfin_write_EBIU_DDRCTL0(CONFIG_EBIU_DDRCTL0_VAL); -# endif -# ifdef CONFIG_EBIU_DDRCTL1_VAL - bfin_write_EBIU_DDRCTL1(CONFIG_EBIU_DDRCTL1_VAL); -# endif -# ifdef CONFIG_EBIU_DDRCTL2_VAL - bfin_write_EBIU_DDRCTL2(CONFIG_EBIU_DDRCTL2_VAL); -# endif -# ifdef CONFIG_EBIU_DDRCTL3_VAL - /* default is disable, so don't need to force this */ - bfin_write_EBIU_DDRCTL3(CONFIG_EBIU_DDRCTL3_VAL); -# endif -# ifdef CONFIG_EBIU_DDRQUE_VAL - bfin_write_EBIU_DDRQUE(bfin_read_EBIU_DDRQUE() | CONFIG_EBIU_DDRQUE_VAL); -# endif -#endif - - serial_putc('e'); -} - -__attribute__((always_inline)) static inline void -check_hibernation(ADI_BOOT_DATA *bs, u16 vr_ctl, bool put_into_srfs) -{ - serial_putc('a'); - - if (!CONFIG_MEM_SIZE) - return; - - serial_putc('b'); - - /* Are we coming out of hibernate (suspend to memory) ? - * The memory layout is: - * 0x0: hibernate magic for anomaly 307 (0xDEADBEEF) - * 0x4: return address - * 0x8: stack pointer - * - * SCKELOW is unreliable on older parts (anomaly 307) - */ - if (ANOMALY_05000307 || vr_ctl & 0x8000) { - uint32_t *hibernate_magic = 0; - __builtin_bfin_ssync(); /* make sure memory controller is done */ - if (hibernate_magic[0] == 0xDEADBEEF) { - serial_putc('c'); - bfin_write_EVT15(hibernate_magic[1]); - bfin_write_IMASK(EVT_IVG15); - __asm__ __volatile__ ( - /* load reti early to avoid anomaly 281 */ - "reti = %0;" - /* clear hibernate magic */ - "[%0] = %1;" - /* load stack pointer */ - "SP = [%0 + 8];" - /* lower ourselves from reset ivg to ivg15 */ - "raise 15;" - "rti;" - : - : "p"(hibernate_magic), "d"(0x2000 /* jump.s 0 */) - ); - } - serial_putc('d'); - } - - serial_putc('e'); -} - -__attribute__((always_inline)) static inline void -program_async_controller(ADI_BOOT_DATA *bs) -{ - serial_putc('a'); - - /* Program the async banks controller. */ - bfin_write_EBIU_AMBCTL0(CONFIG_EBIU_AMBCTL0_VAL); - bfin_write_EBIU_AMBCTL1(CONFIG_EBIU_AMBCTL1_VAL); - bfin_write_EBIU_AMGCTL(CONFIG_EBIU_AMGCTL_VAL); - - serial_putc('b'); - - /* Not all parts have these additional MMRs. */ -#ifdef EBIU_MODE -# ifdef CONFIG_EBIU_MBSCTL_VAL - bfin_write_EBIU_MBSCTL(CONFIG_EBIU_MBSCTL_VAL); -# endif -# ifdef CONFIG_EBIU_MODE_VAL - bfin_write_EBIU_MODE(CONFIG_EBIU_MODE_VAL); -# endif -# ifdef CONFIG_EBIU_FCTL_VAL - bfin_write_EBIU_FCTL(CONFIG_EBIU_FCTL_VAL); -# endif -#endif - - serial_putc('c'); -} - -BOOTROM_CALLED_FUNC_ATTR -void initcode(ADI_BOOT_DATA *bs) -{ - ADI_BOOT_DATA bootstruct_scratch; - - serial_init(); - - serial_putc('A'); - - /* If the bootstruct is NULL, then it's because we're loading - * dynamically and not via LDR (bootrom). So set the struct to - * some scratch space. - */ - if (!bs) - bs = &bootstruct_scratch; - - serial_putc('B'); - bool put_into_srfs = maybe_self_refresh(bs); - - serial_putc('C'); - uint sdivB, divB, vcoB; - program_early_devices(bs, &sdivB, &divB, &vcoB); - - serial_putc('D'); - u16 vr_ctl = program_clocks(bs, put_into_srfs); - - serial_putc('E'); - update_serial_clocks(bs, sdivB, divB, vcoB); - - serial_putc('F'); - program_memory_controller(bs, put_into_srfs); - - serial_putc('G'); - check_hibernation(bs, vr_ctl, put_into_srfs); - - serial_putc('H'); - program_async_controller(bs); - -#ifdef CONFIG_BFIN_BOOTROM_USES_EVT1 - serial_putc('I'); - /* tell the bootrom where our entry point is */ - if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_BYPASS) - bfin_write_EVT1(CONFIG_SYS_MONITOR_BASE); -#endif - - serial_putc('>'); - serial_putc('\n'); - - serial_deinit(); -} |
