diff options
Diffstat (limited to 'board/Marvell/openrd/openrd.c')
| -rw-r--r-- | board/Marvell/openrd/openrd.c | 161 |
1 files changed, 0 insertions, 161 deletions
diff --git a/board/Marvell/openrd/openrd.c b/board/Marvell/openrd/openrd.c deleted file mode 100644 index 55cf525cf8..0000000000 --- a/board/Marvell/openrd/openrd.c +++ /dev/null @@ -1,161 +0,0 @@ -/* - * (C) Copyright 2009 - * Net Insight <www.netinsight.net> - * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net> - * - * Based on sheevaplug.c: - * (C) Copyright 2009 - * Marvell Semiconductor <www.marvell.com> - * Written-by: Prafulla Wadaskar <prafulla@marvell.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <miiphy.h> -#include <asm/arch/cpu.h> -#include <asm/arch/soc.h> -#include <asm/arch/mpp.h> -#include "openrd.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - /* - * default gpio configuration - * There are maximum 64 gpios controlled through 2 sets of registers - * the below configuration configures mainly initial LED status - */ - mvebu_config_gpio(OPENRD_OE_VAL_LOW, - OPENRD_OE_VAL_HIGH, - OPENRD_OE_LOW, OPENRD_OE_HIGH); - - /* Multi-Purpose Pins Functionality configuration */ - static const u32 kwmpp_config[] = { - MPP0_NF_IO2, - MPP1_NF_IO3, - MPP2_NF_IO4, - MPP3_NF_IO5, - MPP4_NF_IO6, - MPP5_NF_IO7, - MPP6_SYSRST_OUTn, - MPP7_GPO, - MPP8_TW_SDA, - MPP9_TW_SCK, - MPP10_UART0_TXD, - MPP11_UART0_RXD, - MPP12_SD_CLK, - MPP13_SD_CMD, /* Alt UART1_TXD */ - MPP14_SD_D0, /* Alt UART1_RXD */ - MPP15_SD_D1, - MPP16_SD_D2, - MPP17_SD_D3, - MPP18_NF_IO0, - MPP19_NF_IO1, - MPP20_GE1_0, - MPP21_GE1_1, - MPP22_GE1_2, - MPP23_GE1_3, - MPP24_GE1_4, - MPP25_GE1_5, - MPP26_GE1_6, - MPP27_GE1_7, - MPP28_GPIO, - MPP29_TSMP9, - MPP30_GE1_10, - MPP31_GE1_11, - MPP32_GE1_12, - MPP33_GE1_13, - MPP34_GPIO, /* UART1 / SD sel */ - MPP35_TDM_CH0_TX_QL, - MPP36_TDM_SPI_CS1, - MPP37_TDM_CH2_TX_QL, - MPP38_TDM_CH2_RX_QL, - MPP39_AUDIO_I2SBCLK, - MPP40_AUDIO_I2SDO, - MPP41_AUDIO_I2SLRC, - MPP42_AUDIO_I2SMCLK, - MPP43_AUDIO_I2SDI, - MPP44_AUDIO_EXTCLK, - MPP45_TDM_PCLK, - MPP46_TDM_FS, - MPP47_TDM_DRX, - MPP48_TDM_DTX, - MPP49_TDM_CH0_RX_QL, - 0 - }; - - kirkwood_mpp_conf(kwmpp_config, NULL); - return 0; -} - -int board_init(void) -{ - /* - * arch number of board - */ -#if defined(CONFIG_BOARD_IS_OPENRD_BASE) - gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE; -#elif defined(CONFIG_BOARD_IS_OPENRD_CLIENT) - gd->bd->bi_arch_number = MACH_TYPE_OPENRD_CLIENT; -#elif defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE) - gd->bd->bi_arch_number = MACH_TYPE_OPENRD_ULTIMATE; -#endif - - /* adress of boot parameters */ - gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; - return 0; -} - -#ifdef CONFIG_RESET_PHY_R -/* Configure and enable MV88E1116/88E1121 PHY */ -void mv_phy_init(char *name) -{ - u16 reg; - u16 devadr; - - if (miiphy_set_current_dev(name)) - return; - - /* command to read PHY dev address */ - if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { - printf("Err..%s could not read PHY dev address\n", - __FUNCTION__); - return; - } - - /* - * Enable RGMII delay on Tx and Rx for CPU port - * Ref: sec 4.7.2 of chip datasheet - */ - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); - miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®); - reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); - miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); - - /* reset the phy */ - miiphy_reset(name, devadr); - - printf(PHY_NO" Initialized on %s\n", name); -} - -void reset_phy(void) -{ - mv_phy_init("egiga0"); - -#ifdef CONFIG_BOARD_IS_OPENRD_CLIENT - /* Kirkwood ethernet driver is written with the assumption that in case - * of multiple PHYs, their addresses are consecutive. But unfortunately - * in case of OpenRD-Client, PHY addresses are not consecutive.*/ - miiphy_write("egiga1", 0xEE, 0xEE, 24); -#endif - -#if defined(CONFIG_BOARD_IS_OPENRD_CLIENT) || \ - defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE) - /* configure and initialize both PHY's */ - mv_phy_init("egiga1"); -#endif -} -#endif /* CONFIG_RESET_PHY_R */ |
