1 files changed, 0 insertions, 86 deletions
diff --git a/arch/arm/include/asm/arch-armada-xp/config.h b/arch/arm/include/asm/arch-armada-xp/config.h
deleted file mode 100644
index f9fd424609..0000000000
--- a/arch/arm/include/asm/arch-armada-xp/config.h
+++ /dev/null
@@ -1,86 +0,0 @@
-/*
- * (C) Copyright 2011
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Lei Wen <leiwen@marvell.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * This file should be included in board config header file.
- *
- * It supports common definitions for Armada XP platforms
- */
-
-#ifndef _ARMADA_XP_CONFIG_H
-#define _ARMADA_XP_CONFIG_H
-
-#include <asm/arch/soc.h>
-
-#define MV88F78X60 /* for the DDR training bin_hdr code */
-
-#define CONFIG_SYS_CACHELINE_SIZE	32
-
-/*
- * By default kwbimage.cfg from board specific folder is used
- * If for some board, different configuration file need to be used,
- * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
- */
-#ifndef CONFIG_SYS_KWD_CONFIG
-#define	CONFIG_SYS_KWD_CONFIG	$(CONFIG_BOARDDIR)/kwbimage.cfg
-#endif /* CONFIG_SYS_KWD_CONFIG */
-
-/* Add target to build it automatically upon "make" */
-#ifdef CONFIG_SPL
-#define CONFIG_BUILD_TARGET	"u-boot-spl.kwb"
-#else
-#define CONFIG_BUILD_TARGET	"u-boot.kwb"
-#endif
-
-/* end of 16M scrubbed by training in bootrom */
-#define CONFIG_SYS_INIT_SP_ADDR		0x00FF0000
-#define CONFIG_NR_DRAM_BANKS_MAX	2
-
-#define MV_UART_CONSOLE_BASE		MVEBU_UART0_BASE
-
-/*
- * SPI Flash configuration
- */
-#ifdef CONFIG_CMD_SF
-#define CONFIG_HARD_SPI			1
-#define CONFIG_KIRKWOOD_SPI		1
-#ifndef CONFIG_ENV_SPI_BUS
-# define CONFIG_ENV_SPI_BUS		0
-#endif
-#ifndef CONFIG_ENV_SPI_CS
-# define CONFIG_ENV_SPI_CS		0
-#endif
-#ifndef CONFIG_ENV_SPI_MAX_HZ
-# define CONFIG_ENV_SPI_MAX_HZ		50000000
-#endif
-#endif
-
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_CMD_MII
-#define CONFIG_MII		/* expose smi ove miiphy interface */
-#define CONFIG_MVNETA		/* Enable Marvell Gbe Controller Driver */
-#define CONFIG_PHYLIB
-#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
-#define CONFIG_PHY_GIGE		/* GbE speed/duplex detect */
-#endif /* CONFIG_CMD_NET */
-
-/*
- * I2C related stuff
- */
-#ifdef CONFIG_CMD_I2C
-#ifndef CONFIG_SYS_I2C_SOFT
-#define CONFIG_I2C_MVTWSI
-#endif
-#define CONFIG_SYS_I2C_SLAVE		0x0
-#define CONFIG_SYS_I2C_SPEED		100000
-#endif
-
-#endif /* _ARMADA_XP_CONFIG_H */