diff options
Diffstat (limited to 'arch/arm/dts/exynos5250-snow.dts')
| -rw-r--r-- | arch/arm/dts/exynos5250-snow.dts | 371 |
1 files changed, 329 insertions, 42 deletions
diff --git a/arch/arm/dts/exynos5250-snow.dts b/arch/arm/dts/exynos5250-snow.dts index e4b3dc29e4..32c0098bd8 100644 --- a/arch/arm/dts/exynos5250-snow.dts +++ b/arch/arm/dts/exynos5250-snow.dts @@ -7,24 +7,28 @@ * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. -*/ + */ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/input/input.h> #include "exynos5250.dtsi" / { model = "Google Snow"; - compatible = "google,snow", "samsung,exynos5250"; + compatible = "google,snow", "samsung,exynos5250", "samsung,exynos5"; aliases { - i2c0 = "/i2c@12c60000"; - i2c1 = "/i2c@12c70000"; - i2c2 = "/i2c@12c80000"; - i2c3 = "/i2c@12c90000"; - i2c4 = "/i2c@12ca0000"; - i2c5 = "/i2c@12cb0000"; - i2c6 = "/i2c@12cc0000"; - i2c7 = "/i2c@12cd0000"; + i2c0 = "/i2c@12C60000"; + i2c1 = "/i2c@12C70000"; + i2c2 = "/i2c@12C80000"; + i2c3 = "/i2c@12C90000"; + i2c4 = "/i2c@12CA0000"; + i2c104 = &i2c_104; + i2c5 = "/i2c@12CB0000"; + i2c6 = "/i2c@12CC0000"; + i2c7 = "/i2c@12CD0000"; spi0 = "/spi@12d20000"; spi1 = "/spi@12d30000"; spi2 = "/spi@12d40000"; @@ -39,18 +43,166 @@ i2s = "/sound@3830000"; }; - i2c4: i2c@12ca0000 { - cros_ec: cros-ec@1e { - reg = <0x1e>; - compatible = "google,cros-ec-i2c"; - i2c-max-frequency = <100000>; - u-boot,i2c-offset-len = <0>; - ec-interrupt = <&gpx1 6 GPIO_ACTIVE_LOW>; + memory { + reg = <0x40000000 0x80000000>; + }; + + chosen { + bootargs = "console=tty1"; + stdout-path = "serial3:115200n8"; + }; + + iram { + reg = <0x02020000 0x60000>; + }; + + config { + samsung,bl1-offset = <0x1400>; + samsung,bl2-offset = <0x3400>; + u-boot-memory = "/memory"; + u-boot-offset = <0x3e00000 0x100000>; + }; + + flash { + reg = <0 0x100000>; + #address-cells = <1>; + #size-cells = <1>; + pre-boot { + label = "bl1 pre-boot"; + reg = <0 0x2000>; + read-only; + filename = "e5250.nbl1.bin"; + type = "blob exynos-bl1"; + required; }; - power-regulator@48 { - compatible = "ti,tps65090"; - reg = <0x48>; + spl { + label = "bl2 spl"; + reg = <0x2000 0x4000>; + read-only; + filename = "bl2.bin"; + type = "blob exynos-bl2 boot,dtb"; + payload = "/flash/ro-boot"; + required; + }; + + ro-boot { + label = "u-boot"; + reg = <0x6000 0x9a000>; + read-only; + type = "blob boot,dtb"; + required; + }; + }; + + i2c-arbitrator { + compatible = "i2c-arb-gpio-challenge"; + #address-cells = <1>; + #size-cells = <0>; + + i2c-parent = <&{/i2c@12CA0000}>; + + our-claim-gpio = <&gpf0 3 GPIO_ACTIVE_LOW>; + their-claim-gpios = <&gpe0 4 GPIO_ACTIVE_LOW>; + slew-delay-us = <10>; + wait-retry-us = <3000>; + wait-free-us = <50000>; + + /* Use ID 104 as a hint that we're on physical bus 4 */ + i2c_104: i2c@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + battery: sbs-battery@b { + compatible = "sbs,sbs-battery"; + reg = <0xb>; + sbs,poll-retry-count = <1>; + }; + + cros_ec: embedded-controller { + compatible = "google,cros-ec-i2c"; + reg = <0x1e>; + interrupts = <6 IRQ_TYPE_NONE>; + interrupt-parent = <&gpx1>; + wakeup-source; + i2c-max-frequency = <100000>; + u-boot,i2c-offset-len = <0>; + ec-interrupt = <&gpx1 6 GPIO_ACTIVE_LOW>; + }; + + power-regulator { + compatible = "ti,tps65090"; + reg = <0x48>; + + regulators { + dcdc1 { + ti,enable-ext-control; + }; + dcdc2 { + ti,enable-ext-control; + }; + dcdc3 { + ti,enable-ext-control; + }; + fet1: fet1 { + regulator-name = "vcd_led"; + ti,overcurrent-wait = <3>; + }; + tps65090_fet2: fet2 { + regulator-name = "video_mid"; + regulator-always-on; + ti,overcurrent-wait = <3>; + }; + fet3 { + regulator-name = "wwan_r"; + regulator-always-on; + ti,overcurrent-wait = <3>; + }; + fet4 { + regulator-name = "sdcard"; + ti,overcurrent-wait = <3>; + }; + fet5 { + regulator-name = "camout"; + regulator-always-on; + ti,overcurrent-wait = <3>; + }; + fet6: fet6 { + regulator-name = "lcd_vdd"; + ti,overcurrent-wait = <3>; + }; + tps65090_fet7: fet7 { + regulator-name = "video_mid_1a"; + regulator-always-on; + ti,overcurrent-wait = <3>; + }; + ldo1 { + }; + ldo2 { + }; + }; + + charger { + compatible = "ti,tps65090-charger"; + }; + }; + }; + }; + + i2c@12CD0000 { + ptn3460: lvds-bridge@20 { + compatible = "nxp,ptn3460"; + reg = <0x20>; + sleep-gpios = <&gpy2 5 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpx1 5 GPIO_ACTIVE_LOW>; + hotplug-gpios = <&gpx0 7 GPIO_ACTIVE_HIGH>; + edid-emulation = <5>; + }; + + soundcodec@22 { + reg = <0x22>; + compatible = "maxim,max98095-codec"; }; }; @@ -66,6 +218,7 @@ spi-max-frequency = <1000000>; spi-deactivate-delay = <100>; + /* Snow did support SPI but the released version used I2C */ embedded-controller { compatible = "google,cros-ec-i2c"; reg = <0x1e>; @@ -85,28 +238,8 @@ status = "disabled"; }; - i2c@12cd0000 { - soundcodec@22 { - reg = <0x22>; - compatible = "maxim,max98095-codec"; - }; - - ptn3460-bridge@20 { - compatible = "nxp,ptn3460"; - reg = <0x20>; - /* - * TODO(sjg@chromium.org): Use GPIOs here - * powerdown-gpio = <&gpy2 5 0>; - * reset-gpio = <&gpx1 5 0>; - * edid-emulation = <5>; - * pinctrl-names = "default"; - * pinctrl-0 = <&ptn3460_gpios>; - */ - }; - }; - - i2c@12c60000 { - pmic@9 { + i2c@12C60000 { + max77686@09 { reg = <0x9>; compatible = "maxim,max77686"; }; @@ -199,4 +332,158 @@ }; +&i2c_0 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <378000>; + + max77686: max77686@09 { + compatible = "maxim,max77686"; + interrupt-parent = <&gpx3>; + interrupts = <2 IRQ_TYPE_NONE>; + wakeup-source; + reg = <0x09>; + #clock-cells = <1>; + + voltage-regulators { + ldo1_reg: LDO1 { + regulator-name = "P1.0V_LDO_OUT1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "P1.8V_LDO_OUT2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "P1.8V_LDO_OUT3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo7_reg: LDO7 { + regulator-name = "P1.1V_LDO_OUT7"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + ldo8_reg: LDO8 { + regulator-name = "P1.0V_LDO_OUT8"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo10_reg: LDO10 { + regulator-name = "P1.8V_LDO_OUT10"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo12_reg: LDO12 { + regulator-name = "P3.0V_LDO_OUT12"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + }; + + ldo14_reg: LDO14 { + regulator-name = "P1.8V_LDO_OUT14"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo15_reg: LDO15 { + regulator-name = "P1.0V_LDO_OUT15"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo16_reg: LDO16 { + regulator-name = "P1.8V_LDO_OUT16"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo17_reg: LDO17 { + regulator-name = "vdd_mydp"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + buck3_reg: BUCK3 { + regulator-name = "vdd_int"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + }; + + buck4_reg: BUCK4 { + regulator-name = "vdd_g3d"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + + buck5_reg: BUCK5 { + regulator-name = "P1.8V_BUCK_OUT5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + buck6_reg: BUCK6 { + regulator-name = "P1.35V_BUCK_OUT6"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + buck7_reg: BUCK7 { + regulator-name = "P2.0V_BUCK_OUT7"; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + regulator-always-on; + }; + + buck8_reg: BUCK8 { + regulator-name = "P2.85V_BUCK_OUT8"; + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + }; + }; + }; +}; + #include "cros-ec-keyboard.dtsi" |
