diff options
Diffstat (limited to 'arch/arm/cpu/armv7/sunxi/board.c')
| -rw-r--r-- | arch/arm/cpu/armv7/sunxi/board.c | 27 |
1 files changed, 11 insertions, 16 deletions
diff --git a/arch/arm/cpu/armv7/sunxi/board.c b/arch/arm/cpu/armv7/sunxi/board.c index 4b2494ea37..5f39aa07cf 100644 --- a/arch/arm/cpu/armv7/sunxi/board.c +++ b/arch/arm/cpu/armv7/sunxi/board.c @@ -45,11 +45,11 @@ static int gpio_init(void) sunxi_gpio_set_cfgpin(SUNXI_GPB(23), SUNXI_GPIO_INPUT); #endif #if defined(CONFIG_MACH_SUN8I) - sunxi_gpio_set_cfgpin(SUNXI_GPF(2), SUN8I_GPF_UART0_TX); - sunxi_gpio_set_cfgpin(SUNXI_GPF(4), SUN8I_GPF_UART0_RX); + sunxi_gpio_set_cfgpin(SUNXI_GPF(2), SUN8I_GPF_UART0); + sunxi_gpio_set_cfgpin(SUNXI_GPF(4), SUN8I_GPF_UART0); #else - sunxi_gpio_set_cfgpin(SUNXI_GPF(2), SUNXI_GPF_UART0_TX); - sunxi_gpio_set_cfgpin(SUNXI_GPF(4), SUNXI_GPF_UART0_RX); + sunxi_gpio_set_cfgpin(SUNXI_GPF(2), SUNXI_GPF_UART0); + sunxi_gpio_set_cfgpin(SUNXI_GPF(4), SUNXI_GPF_UART0); #endif sunxi_gpio_set_pull(SUNXI_GPF(4), 1); #elif CONFIG_CONS_INDEX == 1 && (defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I)) @@ -64,6 +64,10 @@ static int gpio_init(void) sunxi_gpio_set_cfgpin(SUNXI_GPH(20), SUN6I_GPH_UART0); sunxi_gpio_set_cfgpin(SUNXI_GPH(21), SUN6I_GPH_UART0); sunxi_gpio_set_pull(SUNXI_GPH(21), SUNXI_GPIO_PULL_UP); +#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN8I_A33) + sunxi_gpio_set_cfgpin(SUNXI_GPB(0), SUN8I_A33_GPB_UART0); + sunxi_gpio_set_cfgpin(SUNXI_GPB(1), SUN8I_A33_GPB_UART0); + sunxi_gpio_set_pull(SUNXI_GPB(1), SUNXI_GPIO_PULL_UP); #elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN9I) sunxi_gpio_set_cfgpin(SUNXI_GPH(12), SUN9I_GPH_UART0); sunxi_gpio_set_cfgpin(SUNXI_GPH(13), SUN9I_GPH_UART0); @@ -119,20 +123,11 @@ void s_init(void) #ifdef CONFIG_SPL_BUILD /* The sunxi internal brom will try to loader external bootloader * from mmc0, nand flash, mmc2. - * - * Unfortunately we can't check how SPL was loaded so assume it's - * always the first SD/MMC controller, unless it was explicitly - * stated that SPL is on nand flash. + * Unfortunately we can't check how SPL was loaded so assume + * it's always the first SD/MMC controller */ u32 spl_boot_device(void) { -#if defined(CONFIG_SPL_NAND_SUPPORT) - /* - * This is compile time configuration informing SPL, that it - * was loaded from nand flash. - */ - return BOOT_DEVICE_NAND; -#else /* * When booting from the SD card, the "eGON.BT0" signature is expected * to be found in memory at the address 0x0004 (see the "mksunxiboot" @@ -153,7 +148,6 @@ u32 spl_boot_device(void) return BOOT_DEVICE_MMC1; else return BOOT_DEVICE_BOARD; -#endif } /* No confirmation data available in SPL yet. Hardcode bootmode */ @@ -202,6 +196,7 @@ void reset_cpu(ulong addr) writel(WDT_CFG_RESET, &wdog->cfg); writel(WDT_MODE_EN, &wdog->mode); writel(WDT_CTRL_KEY | WDT_CTRL_RESTART, &wdog->ctl); + while (1) { } #endif } |
