summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
Diffstat
-rw-r--r--arch/arm/Kconfig11
-rw-r--r--board/barco/platinum/Kconfig37
-rw-r--r--board/barco/platinum/MAINTAINERS7
-rw-r--r--board/barco/platinum/Makefile14
-rw-r--r--board/barco/platinum/platinum.c217
-rw-r--r--board/barco/platinum/platinum.h88
-rw-r--r--board/barco/platinum/platinum_picon.c244
-rw-r--r--board/barco/platinum/platinum_titanium.c209
-rw-r--r--board/barco/platinum/spl_picon.c182
-rw-r--r--board/barco/platinum/spl_titanium.c185
-rw-r--r--configs/platinum_picon_defconfig4
-rw-r--r--configs/platinum_titanium_defconfig4
-rw-r--r--include/configs/platinum.h319
-rw-r--r--include/configs/platinum_picon.h31
-rw-r--r--include/configs/platinum_titanium.h38
15 files changed, 1590 insertions, 0 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 5eb1d03cfa..dd35992983 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -664,6 +664,16 @@ config TARGET_OT1200
bool "Bachmann OT1200"
select CPU_V7
+config TARGET_PLATINUM_PICON
+ bool "Support platinum-picon"
+ select CPU_V7
+ select SUPPORT_SPL
+
+config TARGET_PLATINUM_TITANIUM
+ bool "Support platinum-titanium"
+ select CPU_V7
+ select SUPPORT_SPL
+
config OMAP34XX
bool "OMAP34XX SoC"
select CPU_V7
@@ -869,6 +879,7 @@ source "board/atmel/sama5d4_xplained/Kconfig"
source "board/atmel/sama5d4ek/Kconfig"
source "board/bachmann/ot1200/Kconfig"
source "board/balloon3/Kconfig"
+source "board/barco/platinum/Kconfig"
source "board/barco/titanium/Kconfig"
source "board/bluegiga/apx4devkit/Kconfig"
source "board/bluewater/snapper9260/Kconfig"
diff --git a/board/barco/platinum/Kconfig b/board/barco/platinum/Kconfig
new file mode 100644
index 0000000000..8bbad24c0d
--- /dev/null
+++ b/board/barco/platinum/Kconfig
@@ -0,0 +1,37 @@
+if TARGET_PLATINUM_PICON
+
+config SYS_CPU
+ default "armv7"
+
+config SYS_VENDOR
+ default "barco"
+
+config SYS_SOC
+ default "mx6"
+
+config SYS_BOARD
+ default "platinum"
+
+config SYS_CONFIG_NAME
+ default "platinum_picon"
+
+endif
+
+if TARGET_PLATINUM_TITANIUM
+
+config SYS_CPU
+ default "armv7"
+
+config SYS_VENDOR
+ default "barco"
+
+config SYS_SOC
+ default "mx6"
+
+config SYS_BOARD
+ default "platinum"
+
+config SYS_CONFIG_NAME
+ default "platinum_titanium"
+
+endif
diff --git a/board/barco/platinum/MAINTAINERS b/board/barco/platinum/MAINTAINERS
new file mode 100644
index 0000000000..a22584b5e5
--- /dev/null
+++ b/board/barco/platinum/MAINTAINERS
@@ -0,0 +1,7 @@
+PLATINUM BOARD
+M: Stefan Roese <sr@denx.de>
+S: Maintained
+F: board/barco/platinum/
+F: include/configs/platinum.h
+F: configs/platinum_picon_defconfig
+F: configs/platinum_titanium_defconfig
diff --git a/board/barco/platinum/Makefile b/board/barco/platinum/Makefile
new file mode 100644
index 0000000000..abc941914a
--- /dev/null
+++ b/board/barco/platinum/Makefile
@@ -0,0 +1,14 @@
+#
+# Copyright (C) 2014, Barco (www.barco.com)
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := platinum.o
+obj-$(CONFIG_TARGET_PLATINUM_PICON) += platinum_picon.o
+obj-$(CONFIG_TARGET_PLATINUM_TITANIUM) += platinum_titanium.o
+
+ifneq ($(CONFIG_SPL_BUILD),)
+obj-$(CONFIG_TARGET_PLATINUM_PICON) += spl_picon.o
+obj-$(CONFIG_TARGET_PLATINUM_TITANIUM) += spl_titanium.o
+endif
diff --git a/board/barco/platinum/platinum.c b/board/barco/platinum/platinum.c
new file mode 100644
index 0000000000..1485a4856f
--- /dev/null
+++ b/board/barco/platinum/platinum.c
@@ -0,0 +1,217 @@
+/*
+ * Copyright (C) 2014, Barco (www.barco.com)
+ * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+
+#include "platinum.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+iomux_v3_cfg_t const usdhc3_pads[] = {
+ MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT5__GPIO7_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+};
+
+iomux_v3_cfg_t nfc_pads[] = {
+ MX6_PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_WP_B__NAND_WP_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_CS1__NAND_CE1_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_CS2__NAND_CE2_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_CS3__NAND_CE3_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_SD4_CMD__NAND_RE_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_SD4_CLK__NAND_WE_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_D0__NAND_DATA00 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_D1__NAND_DATA01 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_D2__NAND_DATA02 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_D3__NAND_DATA03 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_D4__NAND_DATA04 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_D5__NAND_DATA05 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_D6__NAND_DATA06 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_D7__NAND_DATA07 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_SD4_DAT0__NAND_DQS | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+struct fsl_esdhc_cfg usdhc_cfg[] = {
+ { USDHC3_BASE_ADDR },
+};
+
+void setup_gpmi_nand(void)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ /* config gpmi nand iomux */
+ imx_iomux_v3_setup_multiple_pads(nfc_pads, ARRAY_SIZE(nfc_pads));
+
+ /* config gpmi and bch clock to 100 MHz */
+ clrsetbits_le32(&mxc_ccm->cs2cdr,
+ MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK |
+ MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK |
+ MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK,
+ MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) |
+ MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) |
+ MXC_CCM_CS2CDR_ENFC_CLK_SEL(3));
+
+ /* enable gpmi and bch clock gating */
+ setbits_le32(&mxc_ccm->CCGR4,
+ MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
+ MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_OFFSET);
+
+ /* enable apbh clock gating */
+ setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
+}
+
+int dram_init(void)
+{
+ gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+
+ return 0;
+}
+
+int board_ehci_hcd_init(int port)
+{
+ return 0;
+}
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+
+ if (cfg->esdhc_base == usdhc_cfg[0].esdhc_base) {
+ unsigned sd3_cd = IMX_GPIO_NR(7, 0);
+ gpio_direction_input(sd3_cd);
+ return !gpio_get_value(sd3_cd);
+ }
+
+ return 0;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+
+ return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+}
+
+void board_init_gpio(void)
+{
+ platinum_init_gpio();
+}
+
+void board_init_gpmi_nand(void)
+{
+ setup_gpmi_nand();
+}
+
+void board_init_i2c(void)
+{
+ platinum_setup_i2c();
+}
+
+void board_init_spi(void)
+{
+ platinum_setup_spi();
+}
+
+void board_init_uart(void)
+{
+ platinum_setup_uart();
+}
+
+void board_init_usb(void)
+{
+ platinum_init_usb();
+}
+
+void board_init_finished(void)
+{
+ platinum_init_finished();
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+ return platinum_phy_config(phydev);
+}
+
+int board_eth_init(bd_t *bis)
+{
+ return cpu_eth_init(bis);
+}
+
+int board_early_init_f(void)
+{
+ board_init_uart();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+ board_init_spi();
+
+ board_init_i2c();
+
+ board_init_gpmi_nand();
+
+ board_init_gpio();
+
+ board_init_usb();
+
+ board_init_finished();
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: " CONFIG_PLATINUM_BOARD "\n");
+ return 0;
+}
+
+static const struct boot_mode board_boot_modes[] = {
+ /* NAND */
+ { "nand", MAKE_CFGVAL(0x80, 0x02, 0x00, 0x00) },
+ /* 4 bit bus width */
+ { "mmc0", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00) },
+ { "mmc1", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00) },
+ { NULL, 0 },
+};
+
+int misc_init_r(void)
+{
+ add_board_boot_modes(board_boot_modes);
+
+ return 0;
+}
diff --git a/board/barco/platinum/platinum.h b/board/barco/platinum/platinum.h
new file mode 100644
index 0000000000..8650d6d5e0
--- /dev/null
+++ b/board/barco/platinum/platinum.h
@@ -0,0 +1,88 @@
+/*
+ * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _PLATINUM_H_
+#define _PLATINUM_H_
+
+#include <miiphy.h>
+#include <asm/arch/crm_regs.h>
+
+/* Defines */
+
+#define ECSPI1_PAD_CLK (PAD_CTL_SRE_SLOW | PAD_CTL_PUS_100K_DOWN | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_40ohm | \
+ PAD_CTL_HYS)
+#define ECSPI2_PAD_CLK (PAD_CTL_SRE_FAST | PAD_CTL_PUS_100K_DOWN | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
+ PAD_CTL_HYS)
+#define ECSPI_PAD_MOSI (PAD_CTL_SRE_SLOW | PAD_CTL_PUS_100K_DOWN | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_120ohm | \
+ PAD_CTL_HYS)
+#define ECSPI_PAD_MISO (PAD_CTL_SRE_FAST | PAD_CTL_PUS_100K_DOWN | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_40ohm | \
+ PAD_CTL_HYS)
+#define ECSPI_PAD_SS (PAD_CTL_SRE_SLOW | PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_120ohm | \
+ PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
+ PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+#define I2C_PAD_CTRL_SCL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_LOW | \
+ PAD_CTL_DSE_80ohm | PAD_CTL_HYS | \
+ PAD_CTL_ODE | PAD_CTL_SRE_SLOW)
+
+#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | \
+ PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
+ PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | \
+ PAD_CTL_HYS)
+
+
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+#define PC_SCL MUX_PAD_CTRL(I2C_PAD_CTRL_SCL)
+
+/* Prototypes */
+
+int platinum_setup_enet(void);
+int platinum_setup_i2c(void);
+int platinum_setup_spi(void);
+int platinum_setup_uart(void);
+int platinum_phy_config(struct phy_device *phydev);
+int platinum_init_gpio(void);
+int platinum_init_usb(void);
+int platinum_init_finished(void);
+
+static inline void ccgr_init(void)
+{
+ struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ writel(0x00C03F3F, &ccm->CCGR0);
+ writel(0x0030FC03, &ccm->CCGR1);
+ writel(0x0FFFC000, &ccm->CCGR2);
+ writel(0x3FF00000, &ccm->CCGR3);
+ writel(0xFFFFF300, &ccm->CCGR4); /* enable NAND/GPMI/BCH clks */
+ writel(0x0F0000C3, &ccm->CCGR5);
+ writel(0x000003FF, &ccm->CCGR6);
+}
+
+static inline void gpr_init(void)
+{
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+ /* enable AXI cache for VDOA/VPU/IPU */
+ writel(0xF00000CF, &iomux->gpr[4]);
+ /* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+ writel(0x007F007F, &iomux->gpr[6]);
+ writel(0x007F007F, &iomux->gpr[7]);
+}
+
+#endif /* _PLATINUM_H_ */
diff --git a/board/barco/platinum/platinum_picon.c b/board/barco/platinum/platinum_picon.c
new file mode 100644
index 0000000000..b2eab766c5
--- /dev/null
+++ b/board/barco/platinum/platinum_picon.c
@@ -0,0 +1,244 @@
+/*
+ * Copyright (C) 2014, Barco (www.barco.com)
+ * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <i2c.h>
+#include <miiphy.h>
+
+#include "platinum.h"
+
+#define GPIO_IP_NCONFIG IMX_GPIO_NR(5, 18)
+#define GPIO_HK_NCONFIG IMX_GPIO_NR(7, 13)
+#define GPIO_LS_NCONFIG IMX_GPIO_NR(5, 19)
+
+#define GPIO_I2C0_SEL0 IMX_GPIO_NR(5, 2)
+#define GPIO_I2C0_SEL1 IMX_GPIO_NR(1, 11)
+#define GPIO_I2C0_ENBN IMX_GPIO_NR(1, 13)
+
+#define GPIO_I2C2_SEL0 IMX_GPIO_NR(1, 17)
+#define GPIO_I2C2_SEL1 IMX_GPIO_NR(1, 20)
+#define GPIO_I2C2_ENBN IMX_GPIO_NR(1, 14)
+
+#define GPIO_USB_RESET IMX_GPIO_NR(1, 5)
+
+iomux_v3_cfg_t const ecspi1_pads[] = {
+ MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(ECSPI1_PAD_CLK),
+ MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(ECSPI_PAD_MISO),
+ MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(ECSPI_PAD_MOSI),
+ MX6_PAD_CSI0_DAT7__ECSPI1_SS0 | MUX_PAD_CTRL(ECSPI_PAD_SS),
+ MX6_PAD_EIM_D24__ECSPI1_SS2 | MUX_PAD_CTRL(ECSPI_PAD_SS),
+ MX6_PAD_EIM_D25__ECSPI1_SS3 | MUX_PAD_CTRL(ECSPI_PAD_SS),
+};
+
+iomux_v3_cfg_t const ecspi2_pads[] = {
+ MX6_PAD_EIM_CS0__ECSPI2_SCLK | MUX_PAD_CTRL(ECSPI2_PAD_CLK),
+ MX6_PAD_EIM_OE__ECSPI2_MISO | MUX_PAD_CTRL(ECSPI_PAD_MISO),
+ MX6_PAD_EIM_CS1__ECSPI2_MOSI | MUX_PAD_CTRL(ECSPI_PAD_MOSI),
+ MX6_PAD_EIM_RW__ECSPI2_SS0 | MUX_PAD_CTRL(ECSPI_PAD_SS),
+ MX6_PAD_EIM_LBA__ECSPI2_SS1 | MUX_PAD_CTRL(ECSPI_PAD_SS),
+};
+
+iomux_v3_cfg_t const enet_pads[] = {
+ MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_CRS_DV__ENET_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_GPIO_16__ENET_REF_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_RX_ER__ENET_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_RXD0__ENET_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_RXD1__ENET_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_TX_EN__ENET_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_TXD0__ENET_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_TXD1__ENET_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+/* PHY nRESET */
+iomux_v3_cfg_t const phy_reset_pad = {
+ MX6_PAD_SD1_DAT2__GPIO1_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart1_pads[] = {
+ MX6_PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart4_pads[] = {
+ MX6_PAD_CSI0_DAT12__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_CSI0_DAT13__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_CSI0_DAT16__UART4_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_CSI0_DAT17__UART4_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart5_pads[] = {
+ MX6_PAD_CSI0_DAT14__UART5_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_CSI0_DAT15__UART5_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_CSI0_DAT18__UART5_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_CSI0_DAT19__UART5_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const i2c0_mux_pads[] = {
+ MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_SD2_CMD__GPIO1_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_SD2_DAT2__GPIO1_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const i2c2_mux_pads[] = {
+ MX6_PAD_SD1_DAT1__GPIO1_IO17 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_SD1_CLK__GPIO1_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_SD2_DAT1__GPIO1_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+struct i2c_pads_info i2c_pad_info0 = {
+ .scl = {
+ .i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | PC_SCL,
+ .gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | PC_SCL,
+ .gp = IMX_GPIO_NR(5, 27)
+ },
+ .sda = {
+ .i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | PC,
+ .gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | PC,
+ .gp = IMX_GPIO_NR(5, 26)
+ }
+};
+
+struct i2c_pads_info i2c_pad_info2 = {
+ .scl = {
+ .i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | PC_SCL,
+ .gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | PC_SCL,
+ .gp = IMX_GPIO_NR(1, 3)
+ },
+ .sda = {
+ .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | PC,
+ .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | PC,
+ .gp = IMX_GPIO_NR(1, 6)
+ }
+};
+
+/*
+ * This enet related pin-muxing and GPIO handling is done
+ * in SPL U-Boot. For early initialization. And to give the
+ * PHY some time to come out of reset before the U-Boot
+ * ethernet driver tries to access its registers via MDIO.
+ */
+int platinum_setup_enet(void)
+{
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+ unsigned phy_reset = IMX_GPIO_NR(1, 19);
+
+ /* First configure PHY reset GPIO pin */
+ imx_iomux_v3_setup_pad(phy_reset_pad);
+
+ /* Reconfigure enet muxing while PHY is in reset */
+ gpio_direction_output(phy_reset, 0);
+ imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+ mdelay(10);
+ gpio_set_value(phy_reset, 1);
+ udelay(100);
+
+ /* set GPIO_16 as ENET_REF_CLK_OUT */
+ setbits_le32(&iomux->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
+
+ return enable_fec_anatop_clock(ENET_50MHZ);
+}
+
+int platinum_setup_i2c(void)
+{
+ imx_iomux_v3_setup_multiple_pads(i2c0_mux_pads,
+ ARRAY_SIZE(i2c0_mux_pads));
+ imx_iomux_v3_setup_multiple_pads(i2c2_mux_pads,
+ ARRAY_SIZE(i2c2_mux_pads));
+
+ mdelay(10);
+
+ /* Disable i2c mux 0 */
+ gpio_direction_output(GPIO_I2C0_SEL0, 0);
+ gpio_direction_output(GPIO_I2C0_SEL1, 0);
+ gpio_direction_output(GPIO_I2C0_ENBN, 1);
+
+ /* Disable i2c mux 1 */
+ gpio_direction_output(GPIO_I2C2_SEL0, 0);
+ gpio_direction_output(GPIO_I2C2_SEL1, 0);
+ gpio_direction_output(GPIO_I2C2_ENBN, 1);
+
+ udelay(10);
+
+ setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0);
+ setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+
+ /* Disable all leds */
+ i2c_set_bus_num(0);
+ i2c_reg_write(0x60, 0x05, 0x55);
+
+ return 0;
+}
+
+int platinum_setup_spi(void)
+{
+ imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
+ imx_iomux_v3_setup_multiple_pads(ecspi2_pads, ARRAY_SIZE(ecspi2_pads));
+
+ return 0;
+}
+
+int platinum_setup_uart(void)
+{
+ imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+ imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
+ imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
+
+ return 0;
+}
+
+int platinum_phy_config(struct phy_device *phydev)
+{
+ /* Use generic infrastructure, no specific setup */
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+ return 0;
+}
+
+int platinum_init_gpio(void)
+{
+ /* Reset FPGA's */
+ gpio_direction_output(GPIO_IP_NCONFIG, 0);
+ gpio_direction_output(GPIO_HK_NCONFIG, 0);
+ gpio_direction_output(GPIO_LS_NCONFIG, 0);
+ udelay(3);
+ gpio_set_value(GPIO_IP_NCONFIG, 1);
+ gpio_set_value(GPIO_HK_NCONFIG, 1);
+ gpio_set_value(GPIO_LS_NCONFIG, 1);
+
+ /* no dmd configuration yet */
+
+ return 0;
+}
+
+int platinum_init_usb(void)
+{
+ /* Reset usb hub */
+ gpio_direction_output(GPIO_USB_RESET, 0);
+ udelay(100);
+ gpio_set_value(GPIO_USB_RESET, 1);
+
+ return 0;
+}
+
+int platinum_init_finished(void)
+{
+ /* Enable led 0 */
+ i2c_set_bus_num(0);
+ i2c_reg_write(0x60, 0x05, 0x54);
+
+ return 0;
+}
diff --git a/board/barco/platinum/platinum_titanium.c b/board/barco/platinum/platinum_titanium.c
new file mode 100644
index 0000000000..73a955f019
--- /dev/null
+++ b/board/barco/platinum/platinum_titanium.c
@@ -0,0 +1,209 @@
+/*
+ * Copyright (C) 2014, Barco (www.barco.com)
+ * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <miiphy.h>
+#include <micrel.h>
+
+#include "platinum.h"
+
+iomux_v3_cfg_t const ecspi1_pads[] = {
+ MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(ECSPI1_PAD_CLK),
+ MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(ECSPI_PAD_MISO),
+ MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(ECSPI_PAD_MOSI),
+ MX6_PAD_CSI0_DAT7__ECSPI1_SS0 | MUX_PAD_CTRL(ECSPI_PAD_SS),
+ /* non mounted spi nor flash for booting */
+ MX6_PAD_EIM_D19__ECSPI1_SS1 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_EIM_D24__ECSPI1_SS2 | MUX_PAD_CTRL(ECSPI_PAD_SS),
+ MX6_PAD_EIM_D25__ECSPI1_SS3 | MUX_PAD_CTRL(ECSPI_PAD_SS),
+};
+
+iomux_v3_cfg_t const ecspi2_pads[] = {
+ MX6_PAD_EIM_CS0__ECSPI2_SCLK | MUX_PAD_CTRL(ECSPI2_PAD_CLK),
+ MX6_PAD_EIM_OE__ECSPI2_MISO | MUX_PAD_CTRL(ECSPI_PAD_MISO),
+ MX6_PAD_EIM_CS1__ECSPI2_MOSI | MUX_PAD_CTRL(ECSPI_PAD_MOSI),
+ MX6_PAD_EIM_RW__ECSPI2_SS0 | MUX_PAD_CTRL(ECSPI_PAD_SS),
+};
+
+iomux_v3_cfg_t const enet_pads1[] = {
+ MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ /* pin 35 - 1 (PHY_AD2) on reset */
+ MX6_PAD_RGMII_RXC__GPIO6_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* pin 32 - 1 - (MODE0) all */
+ MX6_PAD_RGMII_RD0__GPIO6_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* pin 31 - 1 - (MODE1) all */
+ MX6_PAD_RGMII_RD1__GPIO6_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* pin 28 - 1 - (MODE2) all */
+ MX6_PAD_RGMII_RD2__GPIO6_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* pin 27 - 1 - (MODE3) all */
+ MX6_PAD_RGMII_RD3__GPIO6_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* pin 33 - 1 - (CLK125_EN) 125Mhz clockout enabled */
+ MX6_PAD_RGMII_RX_CTL__GPIO6_IO24 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* pin 42 PHY nRST */
+ MX6_PAD_EIM_D23__GPIO3_IO23 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const enet_pads2[] = {
+ MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart1_pads[] = {
+ MX6_PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart2_pads[] = {
+ MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_EIM_D28__UART2_DTE_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_EIM_D29__UART2_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart4_pads[] = {
+ MX6_PAD_CSI0_DAT12__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_CSI0_DAT13__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_CSI0_DAT16__UART4_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_CSI0_DAT17__UART4_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+struct i2c_pads_info i2c_pad_info0 = {
+ .scl = {
+ .i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | PC_SCL,
+ .gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | PC_SCL,
+ .gp = IMX_GPIO_NR(5, 27)
+ },
+ .sda = {
+ .i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | PC,
+ .gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | PC,
+ .gp = IMX_GPIO_NR(5, 26)
+ }
+};
+
+struct i2c_pads_info i2c_pad_info2 = {
+ .scl = {
+ .i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | PC_SCL,
+ .gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | PC_SCL,
+ .gp = IMX_GPIO_NR(1, 3)
+ },
+ .sda = {
+ .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | PC,
+ .gpio_mode = MX6_PAD_GPIO_16__GPIO7_IO11 | PC,
+ .gp = IMX_GPIO_NR(7, 11)
+ }
+};
+
+/*
+ * This enet related pin-muxing and GPIO handling is done
+ * in SPL U-Boot. For early initialization. And to give the
+ * PHY some time to come out of reset before the U-Boot
+ * ethernet driver tries to access its registers via MDIO.
+ */
+int platinum_setup_enet(void)
+{
+ gpio_direction_output(IMX_GPIO_NR(3, 23), 0);
+ gpio_direction_output(IMX_GPIO_NR(6, 30), 1);
+ gpio_direction_output(IMX_GPIO_NR(6, 25), 1);
+ gpio_direction_output(IMX_GPIO_NR(6, 27), 1);
+ gpio_direction_output(IMX_GPIO_NR(6, 28), 1);
+ gpio_direction_output(IMX_GPIO_NR(6, 29), 1);
+ imx_iomux_v3_setup_multiple_pads(enet_pads1, ARRAY_SIZE(enet_pads1));
+ gpio_direction_output(IMX_GPIO_NR(6, 24), 1);
+
+ /* Need delay 10ms according to KSZ9021 spec */
+ mdelay(10);
+ gpio_set_value(IMX_GPIO_NR(3, 23), 1);
+ udelay(100);
+
+ imx_iomux_v3_setup_multiple_pads(enet_pads2, ARRAY_SIZE(enet_pads2));
+
+ return 0;
+}
+
+int platinum_setup_i2c(void)
+{
+ setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0);
+ setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+
+ return 0;
+}
+
+int platinum_setup_spi(void)
+{
+ imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
+ imx_iomux_v3_setup_multiple_pads(ecspi2_pads, ARRAY_SIZE(ecspi2_pads));
+
+ return 0;
+}
+
+int platinum_setup_uart(void)
+{
+ imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+ imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
+ imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
+
+ return 0;
+}
+
+int platinum_phy_config(struct phy_device *phydev)
+{
+ /* min rx data delay */
+ ksz9021_phy_extended_write(phydev, MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW,
+ 0x0);
+ /* min tx data delay */
+ ksz9021_phy_extended_write(phydev, MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW,
+ 0x0);
+ /* max rx/tx clock delay, min rx/tx control */
+ ksz9021_phy_extended_write(phydev, MII_KSZ9021_EXT_RGMII_CLOCK_SKEW,
+ 0xf0f0);
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+ return 0;
+}
+
+int platinum_init_gpio(void)
+{
+ /* Default GPIO's */
+ /* Toggle CONFIG_n to reset fpga on every boot */
+ gpio_direction_output(IMX_GPIO_NR(5, 18), 0);
+ /* Need delay >=2uS */
+ udelay(3);
+ gpio_set_value(IMX_GPIO_NR(5, 18), 1);
+
+ /* Default pin 1,15 high - DLP_FLASH_WPZ */
+ gpio_direction_output(IMX_GPIO_NR(1, 15), 1);
+
+ return 0;
+}
+
+int platinum_init_usb(void)
+{
+ return 0;
+}
+
+int platinum_init_finished(void)
+{
+ return 0;
+}
diff --git a/board/barco/platinum/spl_picon.c b/board/barco/platinum/spl_picon.c
new file mode 100644
index 0000000000..f421c2108c
--- /dev/null
+++ b/board/barco/platinum/spl_picon.c
@@ -0,0 +1,182 @@
+/*
+ * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ *
+ * Based on: gw_ventana_spl.c which is:
+ * Copyright (C) 2014 Gateworks Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <asm/io.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <spl.h>
+
+#include "platinum.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#undef RTT_NOM_120OHM /* use 120ohm Rtt_nom vs 60ohm (lower power) */
+
+/* Configure MX6Q/DUAL mmdc DDR io registers */
+struct mx6sdl_iomux_ddr_regs mx6sdl_ddr_ioregs = {
+ /* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
+ .dram_sdclk_0 = 0x00020030,
+ .dram_sdclk_1 = 0x00020030,
+ .dram_cas = 0x00020030,
+ .dram_ras = 0x00020030,
+ .dram_reset = 0x00020030,
+ /* SDCKE[0:1]: 100k pull-up */
+ .dram_sdcke0 = 0x00003000,
+ .dram_sdcke1 = 0x00003000,
+ /* SDBA2: pull-up disabled */
+ .dram_sdba2 = 0x00000000,
+ /* SDODT[0:1]: 100k pull-up, 40 ohm */
+ .dram_sdodt0 = 0x00003030,
+ .dram_sdodt1 = 0x00003030,
+ /* SDQS[0:7]: Differential input, 40 ohm */
+ .dram_sdqs0 = 0x00000030,
+ .dram_sdqs1 = 0x00000030,
+ .dram_sdqs2 = 0x00000030,
+ .dram_sdqs3 = 0x00000030,
+ .dram_sdqs4 = 0x00000030,
+ .dram_sdqs5 = 0x00000030,
+ .dram_sdqs6 = 0x00000030,
+ .dram_sdqs7 = 0x00000030,
+ /* DQM[0:7]: Differential input, 40 ohm */
+ .dram_dqm0 = 0x00020030,
+ .dram_dqm1 = 0x00020030,
+ .dram_dqm2 = 0x00020030,
+ .dram_dqm3 = 0x00020030,
+ .dram_dqm4 = 0x00020030,
+ .dram_dqm5 = 0x00020030,
+ .dram_dqm6 = 0x00020030,
+ .dram_dqm7 = 0x00020030,
+};
+
+/* Configure MX6Q/DUAL mmdc GRP io registers */
+struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = {
+ /* DDR3 */
+ .grp_ddr_type = 0x000c0000,
+ .grp_ddrmode_ctl = 0x00020000,
+ /* disable DDR pullups */
+ .grp_ddrpke = 0x00000000,
+ /* ADDR[00:16], SDBA[0:1]: 40 ohm */
+ .grp_addds = 0x00000030,
+ /* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
+ .grp_ctlds = 0x00000030,
+ /* DATA[00:63]: Differential input, 40 ohm */
+ .grp_ddrmode = 0x00020000,
+ .grp_b0ds = 0x00000030,
+ .grp_b1ds = 0x00000030,
+ .grp_b2ds = 0x00000030,
+ .grp_b3ds = 0x00000030,
+ .grp_b4ds = 0x00000030,
+ .grp_b5ds = 0x00000030,
+ .grp_b6ds = 0x00000030,
+ .grp_b7ds = 0x00000030,
+};
+
+/* MT41K256M16HA-125 */
+static struct mx6_ddr3_cfg mt41k256m16ha_125 = {
+ .mem_speed = 1600,
+ .density = 4, /* 4Gbit */
+ .width = 16,
+ .banks = 8,
+ .rowaddr = 15,
+ .coladdr = 10,
+ .pagesz = 2,
+ .trcd = 1375,
+ .trcmin = 4875,
+ .trasmin = 3500,
+};
+
+/*
+ * Values from running the Freescale DDR stress tool via USB
+ */
+static struct mx6_mmdc_calibration mx6dq_mmdc_calib = {
+ /* write leveling calibration determine */
+ .p0_mpwldectrl0 = 0x0044004E,
+ .p0_mpwldectrl1 = 0x001F0023,
+ /* Read DQS Gating calibration */
+ .p0_mpdgctrl0 = 0x02480248,
+ .p0_mpdgctrl1 = 0x0210021C,
+ /* Read Calibration: DQS delay relative to DQ read access */
+ .p0_mprddlctl = 0x42444444,
+ /* Write Calibration: DQ/DM delay relative to DQS write access */
+ .p0_mpwrdlctl = 0x36322C32,
+};
+
+static void spl_dram_init(int width)
+{
+ struct mx6_ddr3_cfg *mem = &mt41k256m16ha_125;
+ struct mx6_ddr_sysinfo sysinfo = {
+ /* width of data bus:0=16,1=32,2=64 */
+ .dsize = width / 32,
+ /* config for full 4GB range so that get_mem_size() works */
+ .cs_density = 32, /* 32Gb per CS */
+ /* single chip select */
+ .ncs = 1,
+ .cs1_mirror = 1,
+ .rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */
+#ifdef RTT_NOM_120OHM
+ .rtt_nom = 2 /*DDR3_RTT_120_OHM*/, /* RTT_Nom = RZQ/2 */
+#else
+ .rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */
+#endif
+ .walat = 0, /* Write additional latency */
+ .ralat = 5, /* Read additional latency */
+ .mif3_mode = 3, /* Command prediction working mode */
+ .bi_on = 1, /* Bank interleaving enabled */
+ .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
+ .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
+ };
+
+ mx6sdl_dram_iocfg(width, &mx6sdl_ddr_ioregs, &mx6sdl_grp_ioregs);
+ mx6_dram_cfg(&sysinfo, &mx6dq_mmdc_calib, mem);
+}
+
+/*
+ * Called from C runtime startup code (arch/arm/lib/crt0.S:_main)
+ * - we have a stack and a place to store GD, both in SRAM
+ * - no variable global data is available
+ */
+void board_init_f(ulong dummy)
+{
+ /* Setup AIPS and disable watchdog */
+ arch_cpu_init();
+
+ ccgr_init();
+ gpr_init();
+
+ /* UART iomux */
+ board_early_init_f();
+
+ /* Setup GP timer */
+ timer_init();
+
+ /* UART clocks enabled and gd valid - init serial console */
+ preloader_console_init();
+
+ /* Init DDR with 32bit width */
+ spl_dram_init(32);
+
+ /* Clear the BSS */
+ memset(__bss_start, 0, __bss_end - __bss_start);
+
+ /*
+ * Setup enet related MUXing early to give the PHY
+ * some time to wake-up from reset
+ */
+ platinum_setup_enet();
+
+ /* load/boot image from boot device */
+ board_init_r(NULL, 0);
+}
diff --git a/board/barco/platinum/spl_titanium.c b/board/barco/platinum/spl_titanium.c
new file mode 100644
index 0000000000..26fe26ba2b
--- /dev/null
+++ b/board/barco/platinum/spl_titanium.c
@@ -0,0 +1,185 @@
+/*
+ * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ *
+ * Based on: gw_ventana_spl.c which is:
+ * Copyright (C) 2014 Gateworks Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <asm/io.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <spl.h>
+
+#include "platinum.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#undef RTT_NOM_120OHM /* use 120ohm Rtt_nom vs 60ohm (lower power) */
+
+/* Configure MX6Q/DUAL mmdc DDR io registers */
+struct mx6dq_iomux_ddr_regs mx6dq_ddr_ioregs = {
+ /* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
+ .dram_sdclk_0 = 0x00020030,
+ .dram_sdclk_1 = 0x00020030,
+ .dram_cas = 0x00020030,
+ .dram_ras = 0x00020030,
+ .dram_reset = 0x00020030,
+ /* SDCKE[0:1]: 100k pull-up */
+ .dram_sdcke0 = 0x00003000,
+ .dram_sdcke1 = 0x00003000,
+ /* SDBA2: pull-up disabled */
+ .dram_sdba2 = 0x00000000,
+ /* SDODT[0:1]: 100k pull-up, 40 ohm */
+ .dram_sdodt0 = 0x00003030,
+ .dram_sdodt1 = 0x00003030,
+ /* SDQS[0:7]: Differential input, 40 ohm */
+ .dram_sdqs0 = 0x00000030,
+ .dram_sdqs1 = 0x00000030,
+ .dram_sdqs2 = 0x00000030,
+ .dram_sdqs3 = 0x00000030,
+ .dram_sdqs4 = 0x00000030,
+ .dram_sdqs5 = 0x00000030,
+ .dram_sdqs6 = 0x00000030,
+ .dram_sdqs7 = 0x00000030,
+ /* DQM[0:7]: Differential input, 40 ohm */
+ .dram_dqm0 = 0x00020030,
+ .dram_dqm1 = 0x00020030,
+ .dram_dqm2 = 0x00020030,
+ .dram_dqm3 = 0x00020030,
+ .dram_dqm4 = 0x00020030,
+ .dram_dqm5 = 0x00020030,
+ .dram_dqm6 = 0x00020030,
+ .dram_dqm7 = 0x00020030,
+};
+
+/* Configure MX6Q/DUAL mmdc GRP io registers */
+struct mx6dq_iomux_grp_regs mx6dq_grp_ioregs = {
+ /* DDR3 */
+ .grp_ddr_type = 0x000c0000,
+ .grp_ddrmode_ctl = 0x00020000,
+ /* disable DDR pullups */
+ .grp_ddrpke = 0x00000000,
+ /* ADDR[00:16], SDBA[0:1]: 40 ohm */
+ .grp_addds = 0x00000030,
+ /* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
+ .grp_ctlds = 0x00000030,
+ /* DATA[00:63]: Differential input, 40 ohm */
+ .grp_ddrmode = 0x00020000,
+ .grp_b0ds = 0x00000030,
+ .grp_b1ds = 0x00000030,
+ .grp_b2ds = 0x00000030,
+ .grp_b3ds = 0x00000030,
+ .grp_b4ds = 0x00000030,
+ .grp_b5ds = 0x00000030,
+ .grp_b6ds = 0x00000030,
+ .grp_b7ds = 0x00000030,
+};
+
+/* MT41J128M16JT-125 */
+static struct mx6_ddr3_cfg mt41j128m16jt_125 = {
+ .mem_speed = 1600,
+ .density = 2,
+ .width = 16,
+ .banks = 8,
+ .rowaddr = 14,
+ .coladdr = 10,
+ .pagesz = 2,
+ .trcd = 1375,
+ .trcmin = 4875,
+ .trasmin = 3500,
+};
+
+static struct mx6_mmdc_calibration mx6dq_mmdc_calib = {
+ /* Write leveling calibration determine */
+ .p0_mpwldectrl0 = 0x001f001f,
+ .p0_mpwldectrl1 = 0x001f001f,
+ .p1_mpwldectrl0 = 0x00440044,
+ .p1_mpwldectrl1 = 0x00440044,
+ /* Read DQS Gating calibration */
+ .p0_mpdgctrl0 = 0x434b0350,
+ .p0_mpdgctrl1 = 0x034c0359,
+ .p1_mpdgctrl0 = 0x434b0350,
+ .p1_mpdgctrl1 = 0x03650348,
+ /* Read Calibration: DQS delay relative to DQ read access */
+ .p0_mprddlctl = 0x4436383b,
+ .p1_mprddlctl = 0x39393341,
+ /* Write Calibration: DQ/DM delay relative to DQS write access */
+ .p0_mpwrdlctl = 0x35373933,
+ .p1_mpwrdlctl = 0x48254a36,
+};
+
+static void spl_dram_init(int width)
+{
+ struct mx6_ddr3_cfg *mem = &mt41j128m16jt_125;
+ struct mx6_ddr_sysinfo sysinfo = {
+ /* width of data bus:0=16,1=32,2=64 */
+ .dsize = width / 32,
+ /* config for full 4GB range so that get_mem_size() works */
+ .cs_density = 32, /* 32Gb per CS */
+ /* single chip select */
+ .ncs = 1,
+ .cs1_mirror = 1,
+ .rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */
+#ifdef RTT_NOM_120OHM
+ .rtt_nom = 2 /*DDR3_RTT_120_OHM*/, /* RTT_Nom = RZQ/2 */
+#else
+ .rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */
+#endif
+ .walat = 0, /* Write additional latency */
+ .ralat = 5, /* Read additional latency */
+ .mif3_mode = 3, /* Command prediction working mode */
+ .bi_on = 1, /* Bank interleaving enabled */
+ .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
+ .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
+ };
+
+ mx6dq_dram_iocfg(width, &mx6dq_ddr_ioregs, &mx6dq_grp_ioregs);
+ mx6_dram_cfg(&sysinfo, &mx6dq_mmdc_calib, mem);
+}
+
+/*
+ * Called from C runtime startup code (arch/arm/lib/crt0.S:_main)
+ * - we have a stack and a place to store GD, both in SRAM
+ * - no variable global data is available
+ */
+void board_init_f(ulong dummy)
+{
+ /* Setup AIPS and disable watchdog */
+ arch_cpu_init();
+
+ ccgr_init();
+ gpr_init();
+
+ /* UART iomux */
+ board_early_init_f();
+
+ /* Setup GP timer */
+ timer_init();
+
+ /* UART clocks enabled and gd valid - init serial console */
+ preloader_console_init();
+
+ /* Init DDR with 32bit width */
+ spl_dram_init(32);
+
+ /* Clear the BSS */
+ memset(__bss_start, 0, __bss_end - __bss_start);
+
+ /*
+ * Setup enet related MUXing early to give the PHY
+ * some time to wake-up from reset
+ */
+ platinum_setup_enet();
+
+ /* load/boot image from boot device */
+ board_init_r(NULL, 0);
+}
diff --git a/configs/platinum_picon_defconfig b/configs/platinum_picon_defconfig
new file mode 100644
index 0000000000..c3ca0400a1
--- /dev/null
+++ b/configs/platinum_picon_defconfig
@@ -0,0 +1,4 @@
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,MX6DL"
++S:CONFIG_ARM=y
++S:CONFIG_TARGET_PLATINUM_PICON=y
diff --git a/configs/platinum_titanium_defconfig b/configs/platinum_titanium_defconfig
new file mode 100644
index 0000000000..db8cef9cf4
--- /dev/null
+++ b/configs/platinum_titanium_defconfig
@@ -0,0 +1,4 @@
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,MX6Q"
++S:CONFIG_ARM=y
++S:CONFIG_TARGET_PLATINUM_TITANIUM=y
diff --git a/include/configs/platinum.h b/include/configs/platinum.h
new file mode 100644
index 0000000000..134bb45887
--- /dev/null
+++ b/include/configs/platinum.h
@@ -0,0 +1,319 @@
+/*
+ * Copyright (C) 2014, Barco (www.barco.com)
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __PLATINUM_CONFIG_H__
+#define __PLATINUM_CONFIG_H__
+
+#define CONFIG_SYS_GENERIC_BOARD
+
+/* SPL */
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+
+/* Location in NAND to read U-Boot from */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (14 * 1024 * 1024)
+
+#include "imx6_spl.h" /* common IMX6 SPL configuration */
+#include "mx6_common.h"
+#include <asm/arch/imx-regs.h>
+#include <asm/imx-common/gpio.h>
+
+/*
+ * Console configuration
+ */
+
+#include <config_cmd_default.h>
+#define CONFIG_CMD_BMODE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_FUSE
+#define CONFIG_CMD_GPIO
+#define CONFIG_CMD_I2C
+#undef CONFIG_CMD_IMLS
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NAND_TRIMFFS
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_TIME
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_CMD_USB
+
+/*
+ * Hardware configuration
+ */
+
+/* GPIO config */
+#define CONFIG_MXC_GPIO
+
+/* UART config */
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART1_BASE
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_CONS_INDEX 1
+
+/* I2C config */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_SPEED 100000
+
+/* MMC config */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR 0
+#define CONFIG_SYS_FSL_USDHC_NUM 1
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_BOUNCE_BUFFER
+#define CONFIG_DOS_PARTITION
+
+/* Ethernet config */
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE ENET_BASE_ADDR
+
+#define CONFIG_PHYLIB
+
+/* USB config */
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX6
+#define CONFIG_USB_STORAGE
+#define CONFIG_MXC_USB_PORT 1
+#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS 0
+
+/* Memory config */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+#ifndef PHYS_SDRAM_SIZE
+#define PHYS_SDRAM_SIZE (1024 << 20)
+#endif
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_SP_OFFSET)
+
+#define CONFIG_SYS_MALLOC_LEN (16 * 1024 * 1024)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+#ifdef CONFIG_CMD_NAND
+
+/* NAND config */
+#define CONFIG_NAND_MXS
+#ifndef CONFIG_SYS_NAND_MAX_CHIPS
+#define CONFIG_SYS_NAND_MAX_CHIPS 2
+#endif
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE 0x40000000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* DMA config, needed for GPMI/MXS NAND support */
+#define CONFIG_APBH_DMA
+#define CONFIG_APBH_DMA_BURST
+#define CONFIG_APBH_DMA_BURST8
+
+/* Fuse support */
+#define CONFIG_MXC_OCOTP
+
+/* Environment in NAND */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET (16 << 20)
+#define CONFIG_ENV_SECT_SIZE (128 << 10)
+#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + (512 << 10))
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
+
+#else /* CONFIG_CMD_NAND */
+
+/* Environment in MMC */
+#define CONFIG_ENV_SIZE (8 << 10)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET (6 * 64 * 1024)
+#define CONFIG_SYS_MMC_ENV_DEV 0
+
+#endif /* CONFIG_CMD_NAND */
+
+/*
+ * U-Boot configuration
+ */
+
+/* Console boot messages */
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+/* Tag config */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+
+/* Board startup config */
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_MISC_INIT_R
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+/* Device tree support */
+#define CONFIG_OF_LIBFDT
+
+#define CONFIG_LOADADDR 0x12000000
+#define CONFIG_SYS_TEXT_BASE 0x17800000
+
+#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + \
+ PHYS_SDRAM_SIZE - (12 << 20))
+
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTCOMMAND "run bootubi_scr"
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_HUSH_PARSER
+
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_PREBOOT
+
+#define CONFIG_SYS_CBSIZE 256
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+
+/* MTD/UBI/UBIFS config */
+#define CONFIG_LZO
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_RBTREE
+
+#if (CONFIG_SYS_NAND_MAX_CHIPS == 1)
+#define MTDIDS_DEFAULT "nand0=gpmi-nand"
+#define MTDPARTS_DEFAULT "mtdparts=gpmi-nand:14M(spl),2M(uboot)," \
+ "512k(env1),512k(env2),-(ubi)"
+#elif (CONFIG_SYS_NAND_MAX_CHIPS == 2)
+#define MTDIDS_DEFAULT "nand0=gpmi-nand"
+#define MTDPARTS_DEFAULT "mtdparts=gpmi-nand:14M(spl),2M(uboot)," \
+ "512k(env1),512k(env2),495M(ubi0)," \
+ "14M(res0),2M(res1)," \
+ "512k(res2),512k(res3),-(ubi1)"
+#endif
+
+#ifndef CONFIG_SYS_DCACHE_OFF
+#define CONFIG_CMD_CACHE
+#endif
+
+/*
+ * Environment configuration
+ */
+
+#if (CONFIG_SYS_NAND_MAX_CHIPS == 1)
+#define CONFIG_COMMON_ENV_UBI \
+ "setubipartition=env set ubipartition ubi\0" \
+ "setubirfs=env set ubirfs $ubipartition:rootfs$boot_vol\0"
+#elif (CONFIG_SYS_NAND_MAX_CHIPS == 2)
+#define CONFIG_COMMON_ENV_UBI \
+ "setubipartition=env set ubipartition ubi$boot_vol\0" \
+ "setubirfs=env set ubirfs ubi0:rootfs\0"
+#endif
+
+#define CONFIG_COMMON_ENV_MISC \
+ "user=user\0" \
+ "project="CONFIG_PLATINUM_PROJECT"\0" \
+ "uimage=uImage\0" \
+ "dtb="CONFIG_PLATINUM_CPU"-platinum-"CONFIG_PLATINUM_PROJECT".dtb\0" \
+ "serverip=serverip\0" \
+ "memaddrlinux=0x10800000\0" \
+ "memaddrsrc=0x11000000\0" \
+ "memaddrdtb=0x12000000\0" \
+ "console=ttymxc0\0" \
+ "baudrate=115200\0" \
+ "boot_scr=boot.uboot\0" \
+ "boot_vol=0\0" \
+ "mtdids="MTDIDS_DEFAULT"\0" \
+ "mtdparts="MTDPARTS_DEFAULT"\0" \
+ "mmcfs=ext2\0" \
+ "mmcrootpart=1\0" \
+ \
+ "setnfspath=env set nfspath /home/nfs/$user/$project/root\0" \
+ "settftpfilelinux=env set tftpfilelinux $user/$project/$uimage\0" \
+ "settftpfiledtb=env set tftpfiledtb $user/$project/$dtb\0" \
+ "setubifilelinux=env set ubifilelinux boot/$uimage\0" \
+ "setubipfiledtb=env set ubifiledtb boot/$dtb\0" \
+ "setmmcrootdev=env set mmcrootdev /dev/mmcblk0p$mmcrootpart\0" \
+ "setmmcfilelinux=env set mmcfilelinux /boot/$uimage\0" \
+ "setmmcfiledtb=env set mmcfiledtb /boot/$dtb\0" \
+ \
+ "loadtftpkernel=dhcp $memaddrlinux $tftpfilelinux\0" \
+ "loadtftpdtb=dhcp $memaddrdtb $tftpfiledtb\0" \
+ "loadubikernel=ubifsload $memaddrlinux $ubifilelinux\0" \
+ "loadubidtb=ubifsload $memaddrdtb $ubifiledtb\0" \
+ "loadmmckernel=${mmcfs}load mmc 0:$mmcrootpart $memaddrlinux " \
+ "$mmcfilelinux\0" \
+ "loadmmcdtb=${mmcfs}load mmc 0:$mmcrootpart $memaddrdtb " \
+ "$mmcfiledtb\0" \
+ \
+ "ubipart=ubi part $ubipartition\0" \
+ "ubimount=ubifsmount $ubirfs\0" \
+ \
+ "setbootargscommon=env set bootargs $bootargs " \
+ "console=$console,$baudrate enable_wait_mode=off\0" \
+ "setbootargsmtd=env set bootargs $bootargs $mtdparts\0" \
+ "setbootargsdhcp=env set bootargs $bootargs ip=dhcp\0" \
+ "setbootargsubirfs=env set bootargs $bootargs " \
+ "ubi.mtd=$ubipartition root=$ubirfs rootfstype=ubifs\0" \
+ "setbootargsnfsrfs=env set bootargs $bootargs root=/dev/nfs " \
+ "nfsroot=$serverip:$nfspath,v3,tcp\0" \
+ "setbootargsmmcrfs=env set bootargs $bootargs " \
+ "root=$mmcrootdev rootwait rw\0" \
+ \
+ "bootnet=run settftpfilelinux settftpfiledtb setnfspath " \
+ "setbootargscommon setbootargsmtd setbootargsdhcp " \
+ "setbootargsnfsrfs;" \
+ "run loadtftpkernel loadtftpdtb;" \
+ "bootm $memaddrlinux - $memaddrdtb\0" \
+ "bootnet_ubirfs=run settftpfilelinux settftpfiledtb;" \
+ "run setubipartition setubirfs;" \
+ "run setbootargscommon setbootargsmtd " \
+ "setbootargsubirfs;" \
+ "run loadtftpkernel loadtftpdtb;" \
+ "bootm $memaddrlinux - $memaddrdtb\0" \
+ "bootubi=run setubipartition setubirfs setubifilelinux " \
+ "setubipfiledtb;" \
+ "run setbootargscommon setbootargsmtd " \
+ "setbootargsubirfs;" \
+ "run ubipart ubimount loadubikernel loadubidtb;" \
+ "bootm $memaddrlinux - $memaddrdtb\0" \
+ "bootubi_scr=run setubipartition setubirfs;" \
+ "run ubipart ubimount;" \
+ "if ubifsload ${memaddrsrc} boot/${boot_scr}; " \
+ "then source ${memaddrsrc}; else run bootubi; fi\0" \
+ "bootmmc=run setmmcrootdev setmmcfilelinux setmmcfiledtb " \
+ "setbootargscommon setbootargsmmcrfs;" \
+ "run loadmmckernel loadmmcdtb;" \
+ "bootm $memaddrlinux - $memaddrdtb\0" \
+ \
+ "bootcmd="CONFIG_BOOTCOMMAND"\0"
+
+#define CONFIG_COMMON_ENV_SETTINGS CONFIG_COMMON_ENV_MISC \
+ CONFIG_COMMON_ENV_UBI
+#endif /* __PLATINUM_CONFIG_H__ */
diff --git a/include/configs/platinum_picon.h b/include/configs/platinum_picon.h
new file mode 100644
index 0000000000..4590df5a9e
--- /dev/null
+++ b/include/configs/platinum_picon.h
@@ -0,0 +1,31 @@
+/*
+ * Copyright (C) 2014, Barco (www.barco.com)
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __PLATINUM_PICON_CONFIG_H__
+#define __PLATINUM_PICON_CONFIG_H__
+
+#define CONFIG_PLATINUM_PICON
+#define CONFIG_PLATINUM_BOARD "Barco Picon"
+#define CONFIG_PLATINUM_PROJECT "picon"
+#define CONFIG_PLATINUM_CPU "imx6dl"
+
+#define CONFIG_MX6
+
+#include <configs/platinum.h>
+
+#define CONFIG_FEC_XCV_TYPE RMII
+#define CONFIG_FEC_MXC_PHYADDR 0
+
+#define CONFIG_HOSTNAME picon
+
+#define CONFIG_SYS_PROMPT "picon > "
+
+#define CONFIG_PLATFORM_ENV_SETTINGS "\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS CONFIG_COMMON_ENV_SETTINGS \
+ CONFIG_PLATFORM_ENV_SETTINGS
+
+#endif /* __PLATINUM_PICON_CONFIG_H__ */
diff --git a/include/configs/platinum_titanium.h b/include/configs/platinum_titanium.h
new file mode 100644
index 0000000000..678965505f
--- /dev/null
+++ b/include/configs/platinum_titanium.h
@@ -0,0 +1,38 @@
+/*
+ * Copyright (C) 2014, Barco (www.barco.com)
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __PLATINUM_TITANIUM_CONFIG_H__
+#define __PLATINUM_TITANIUM_CONFIG_H__
+
+#define CONFIG_PLATINUM_TITANIUM
+#define CONFIG_PLATINUM_BOARD "Barco Titanium"
+#define CONFIG_PLATINUM_PROJECT "titanium"
+#define CONFIG_PLATINUM_CPU "imx6q"
+
+#define CONFIG_MX6
+
+#define PHYS_SDRAM_SIZE (512 << 20)
+#define CONFIG_SYS_NAND_MAX_CHIPS 1
+
+#include <configs/platinum.h>
+
+#define CONFIG_FEC_XCV_TYPE RGMII
+#define CONFIG_FEC_MXC_PHYADDR 4
+
+#define CONFIG_PHY_MICREL
+#define CONFIG_PHY_MICREL_KSZ9021
+#define CONFIG_PHY_RESET_DELAY 1000
+
+#define CONFIG_HOSTNAME titanium
+
+#define CONFIG_SYS_PROMPT "titanium > "
+
+#define CONFIG_PLATFORM_ENV_SETTINGS "\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS CONFIG_COMMON_ENV_SETTINGS \
+ CONFIG_PLATFORM_ENV_SETTINGS
+
+#endif /* __PLATINUM_TITANIUM_CONFIG_H__ */
OpenPOWER on IntegriCloud