diff options
28 files changed, 833 insertions, 72 deletions
diff --git a/arch/powerpc/cpu/mpc85xx/cmd_errata.c b/arch/powerpc/cpu/mpc85xx/cmd_errata.c index 5d72f4c342..422782ca8f 100644 --- a/arch/powerpc/cpu/mpc85xx/cmd_errata.c +++ b/arch/powerpc/cpu/mpc85xx/cmd_errata.c @@ -255,6 +255,9 @@ static int do_errata(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) #ifdef CONFIG_SYS_P4080_ERRATUM_PCIE_A003 puts("Work-around for Erratum PCIe-A003 enabled\n"); #endif +#ifdef CONFIG_SYS_FSL_ERRATUM_USB14 + puts("Work-around for Erratum USB14 enabled\n"); +#endif return 0; } diff --git a/arch/powerpc/cpu/mpc85xx/cpu.c b/arch/powerpc/cpu/mpc85xx/cpu.c index df2ab6d73c..6ce483e17a 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu.c +++ b/arch/powerpc/cpu/mpc85xx/cpu.c @@ -282,14 +282,6 @@ unsigned long get_tbclk (void) #if defined(CONFIG_WATCHDOG) void -watchdog_reset(void) -{ - int re_enable = disable_interrupts(); - reset_85xx_watchdog(); - if (re_enable) enable_interrupts(); -} - -void reset_85xx_watchdog(void) { /* @@ -297,6 +289,16 @@ reset_85xx_watchdog(void) */ mtspr(SPRN_TSR, TSR_WIS); } + +void +watchdog_reset(void) +{ + int re_enable = disable_interrupts(); + + reset_85xx_watchdog(); + if (re_enable) + enable_interrupts(); +} #endif /* CONFIG_WATCHDOG */ /* diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init.c b/arch/powerpc/cpu/mpc85xx/cpu_init.c index de9d916111..53713e31d4 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu_init.c +++ b/arch/powerpc/cpu/mpc85xx/cpu_init.c @@ -623,6 +623,20 @@ skip_l2: } #endif +#ifdef CONFIG_SYS_FSL_ERRATUM_USB14 + /* On P204x/P304x/P50x0 Rev1.0, USB transmit will result internal + * multi-bit ECC errors which has impact on performance, so software + * should disable all ECC reporting from USB1 and USB2. + */ + if (IS_SVR_REV(get_svr(), 1, 0)) { + struct dcsr_dcfg_regs *dcfg = (struct dcsr_dcfg_regs *) + (CONFIG_SYS_DCSRBAR + CONFIG_SYS_DCSR_DCFG_OFFSET); + setbits_be32(&dcfg->ecccr1, + (DCSR_DCFG_ECC_DISABLE_USB1 | + DCSR_DCFG_ECC_DISABLE_USB2)); + } +#endif + #ifdef CONFIG_FMAN_ENET fman_enet_init(); #endif diff --git a/arch/powerpc/cpu/mpc85xx/fdt.c b/arch/powerpc/cpu/mpc85xx/fdt.c index 24eb9789be..288f7b2860 100644 --- a/arch/powerpc/cpu/mpc85xx/fdt.c +++ b/arch/powerpc/cpu/mpc85xx/fdt.c @@ -663,6 +663,13 @@ void ft_cpu_setup(void *blob, bd_t *bd) #ifdef CONFIG_FSL_CORENET do_fixup_by_compat_u32(blob, "fsl,qoriq-clockgen-1.0", "clock-frequency", CONFIG_SYS_CLK_FREQ, 1); + do_fixup_by_compat_u32(blob, "fsl,qoriq-clockgen-2", + "clock-frequency", CONFIG_SYS_CLK_FREQ, 1); + do_fixup_by_compat_u32(blob, "fsl,mpic", + "clock-frequency", get_bus_freq(0)/2, 1); +#else + do_fixup_by_compat_u32(blob, "fsl,mpic", + "clock-frequency", get_bus_freq(0), 1); #endif fdt_fixup_memory(blob, (u64)bd->bi_memstart, (u64)bd->bi_memsize); diff --git a/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c b/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c index 825a29238d..b621adf4af 100644 --- a/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c +++ b/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c @@ -103,6 +103,10 @@ static const struct { { 22, 168, FSL_SRDS_BANK_3 }, { 23, 169, FSL_SRDS_BANK_3 }, #endif +#if SRDS_MAX_BANK > 3 + { 24, 175, FSL_SRDS_BANK_4 }, + { 25, 176, FSL_SRDS_BANK_4 }, +#endif }; int serdes_get_lane_idx(int lane) diff --git a/arch/powerpc/cpu/mpc85xx/p2041_ids.c b/arch/powerpc/cpu/mpc85xx/p2041_ids.c index 91d9cac568..ef685fea09 100644 --- a/arch/powerpc/cpu/mpc85xx/p2041_ids.c +++ b/arch/powerpc/cpu/mpc85xx/p2041_ids.c @@ -27,16 +27,16 @@ #ifdef CONFIG_SYS_DPAA_QBMAN struct qportal_info qp_info[CONFIG_SYS_QMAN_NUM_PORTALS] = { /* dqrr liodn, frame data liodn, liodn off, sdest */ - SET_QP_INFO(1, 2, 1, 0), - SET_QP_INFO(3, 4, 2, 1), - SET_QP_INFO(5, 6, 3, 2), - SET_QP_INFO(7, 8, 4, 3), - SET_QP_INFO(9, 10, 5, 0), - SET_QP_INFO(11, 12, 1, 1), - SET_QP_INFO(13, 14, 2, 2), - SET_QP_INFO(15, 16, 3, 3), - SET_QP_INFO(17, 18, 4, 0), /* for now sdest to 0 */ - SET_QP_INFO(19, 20, 5, 0), /* for now sdest to 0 */ + SET_QP_INFO(1, 2, 1, 0), + SET_QP_INFO(3, 4, 2, 1), + SET_QP_INFO(5, 6, 3, 2), + SET_QP_INFO(7, 8, 4, 3), + SET_QP_INFO(9, 10, 5, 0), + SET_QP_INFO(11, 12, 6, 1), + SET_QP_INFO(13, 14, 7, 2), + SET_QP_INFO(15, 16, 8, 3), + SET_QP_INFO(17, 18, 9, 0), /* for now sdest to 0 */ + SET_QP_INFO(19, 20, 10, 0), /* for now sdest to 0 */ }; #endif diff --git a/arch/powerpc/cpu/mpc85xx/p3041_ids.c b/arch/powerpc/cpu/mpc85xx/p3041_ids.c index e46a714dcc..cab03f8ab6 100644 --- a/arch/powerpc/cpu/mpc85xx/p3041_ids.c +++ b/arch/powerpc/cpu/mpc85xx/p3041_ids.c @@ -27,16 +27,16 @@ #ifdef CONFIG_SYS_DPAA_QBMAN struct qportal_info qp_info[CONFIG_SYS_QMAN_NUM_PORTALS] = { /* dqrr liodn, frame data liodn, liodn off, sdest */ - SET_QP_INFO(1, 2, 1, 0), - SET_QP_INFO(3, 4, 2, 1), - SET_QP_INFO(5, 6, 3, 2), - SET_QP_INFO(7, 8, 4, 3), - SET_QP_INFO(9, 10, 5, 0), - SET_QP_INFO(11, 12, 1, 1), - SET_QP_INFO(13, 14, 2, 2), - SET_QP_INFO(15, 16, 3, 3), - SET_QP_INFO(17, 18, 4, 0), /* for now sdest to 0 */ - SET_QP_INFO(19, 20, 5, 0), /* for now sdest to 0 */ + SET_QP_INFO(1, 2, 1, 0), + SET_QP_INFO(3, 4, 2, 1), + SET_QP_INFO(5, 6, 3, 2), + SET_QP_INFO(7, 8, 4, 3), + SET_QP_INFO(9, 10, 5, 0), + SET_QP_INFO(1, 12, 6, 1), + SET_QP_INFO(13, 14, 7, 2), + SET_QP_INFO(15, 16, 8, 3), + SET_QP_INFO(17, 18, 9, 0), /* for now sdest to 0 */ + SET_QP_INFO(19, 20, 10, 0), /* for now sdest to 0 */ }; #endif diff --git a/arch/powerpc/cpu/mpc85xx/p5020_ids.c b/arch/powerpc/cpu/mpc85xx/p5020_ids.c index e8c26bf44c..ca05b9cb2b 100644 --- a/arch/powerpc/cpu/mpc85xx/p5020_ids.c +++ b/arch/powerpc/cpu/mpc85xx/p5020_ids.c @@ -27,16 +27,16 @@ #ifdef CONFIG_SYS_DPAA_QBMAN struct qportal_info qp_info[CONFIG_SYS_QMAN_NUM_PORTALS] = { /* dqrr liodn, frame data liodn, liodn off, sdest */ - SET_QP_INFO(1, 2, 1, 0), - SET_QP_INFO(3, 4, 2, 1), - SET_QP_INFO(5, 6, 3, 0), - SET_QP_INFO(7, 8, 4, 1), - SET_QP_INFO(9, 10, 5, 0), - SET_QP_INFO(11, 12, 1, 1), - SET_QP_INFO(13, 14, 2, 0), - SET_QP_INFO(15, 16, 3, 1), - SET_QP_INFO(17, 18, 4, 0), - SET_QP_INFO(19, 20, 5, 1), + SET_QP_INFO(1, 2, 1, 0), + SET_QP_INFO(3, 4, 2, 1), + SET_QP_INFO(5, 6, 3, 0), + SET_QP_INFO(7, 8, 4, 1), + SET_QP_INFO(9, 10, 5, 0), + SET_QP_INFO(11, 12, 6, 1), + SET_QP_INFO(13, 14, 7, 0), + SET_QP_INFO(15, 16, 8, 1), + SET_QP_INFO(17, 18, 9, 0), + SET_QP_INFO(19, 20, 10, 1), }; #endif diff --git a/arch/powerpc/cpu/mpc85xx/portals.c b/arch/powerpc/cpu/mpc85xx/portals.c index b59ef69f1f..d529095ee8 100644 --- a/arch/powerpc/cpu/mpc85xx/portals.c +++ b/arch/powerpc/cpu/mpc85xx/portals.c @@ -30,11 +30,9 @@ #include <asm/fsl_portals.h> #include <asm/fsl_liodn.h> -static ccsr_qman_t *qman = (void *)CONFIG_SYS_FSL_QMAN_ADDR; -static ccsr_bman_t *bman = (void *)CONFIG_SYS_FSL_BMAN_ADDR; - void setup_portals(void) { + ccsr_qman_t *qman = (void *)CONFIG_SYS_FSL_QMAN_ADDR; #ifdef CONFIG_FSL_CORENET int i; @@ -166,6 +164,20 @@ static int fdt_qportal(void *blob, int off, int id, char *name, num = get_dpaa_liodn(dev, &liodns[0], id); ret = fdt_setprop(blob, childoff, "fsl,liodn", &liodns[0], sizeof(u32) * num); + if (!strncmp(name, "pme", 3)) { + u32 pme_rev1, pme_rev2; + ccsr_pme_t *pme_regs = + (void *)CONFIG_SYS_FSL_CORENET_PME_ADDR; + + pme_rev1 = in_be32(&pme_regs->pm_ip_rev_1); + pme_rev2 = in_be32(&pme_regs->pm_ip_rev_2); + ret = fdt_setprop(blob, childoff, + "fsl,pme-rev1", &pme_rev1, sizeof(u32)); + if (ret < 0) + return ret; + ret = fdt_setprop(blob, childoff, + "fsl,pme-rev2", &pme_rev2, sizeof(u32)); + } #endif } else { return childoff; @@ -183,6 +195,7 @@ void fdt_fixup_qportals(void *blob) int off, err; unsigned int maj, min; unsigned int ip_cfg; + ccsr_qman_t *qman = (void *)CONFIG_SYS_FSL_QMAN_ADDR; u32 rev_1 = in_be32(&qman->ip_rev_1); u32 rev_2 = in_be32(&qman->ip_rev_2); char compat[64]; @@ -272,6 +285,7 @@ void fdt_fixup_bportals(void *blob) int off, err; unsigned int maj, min; unsigned int ip_cfg; + ccsr_bman_t *bman = (void *)CONFIG_SYS_FSL_BMAN_ADDR; u32 rev_1 = in_be32(&bman->ip_rev_1); u32 rev_2 = in_be32(&bman->ip_rev_2); char compat[64]; diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h index d57c178f7f..7267611cbc 100644 --- a/arch/powerpc/include/asm/config_mpc85xx.h +++ b/arch/powerpc/include/asm/config_mpc85xx.h @@ -333,7 +333,9 @@ #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011 +#define CONFIG_SYS_FSL_ERRATUM_USB14 #define CONFIG_SYS_FSL_ERRATUM_CPU_A003999 +#define CONFIG_SYS_FSL_ERRATUM_DDR_A003 #define CONFIG_SYS_FSL_ERRATUM_DDR_A003474 #define CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER #define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 @@ -365,7 +367,9 @@ #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011 +#define CONFIG_SYS_FSL_ERRATUM_USB14 #define CONFIG_SYS_FSL_ERRATUM_CPU_A003999 +#define CONFIG_SYS_FSL_ERRATUM_DDR_A003 #define CONFIG_SYS_FSL_ERRATUM_DDR_A003474 #define CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER #define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 @@ -442,6 +446,8 @@ #define CONFIG_SYS_FSL_USB2_PHY_ENABLE #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 +#define CONFIG_SYS_FSL_ERRATUM_USB14 +#define CONFIG_SYS_FSL_ERRATUM_DDR_A003 #define CONFIG_SYS_FSL_ERRATUM_DDR_A003474 #define CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER #define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 @@ -473,7 +479,7 @@ #define CONFIG_SYS_FSL_USB2_PHY_ENABLE #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 -#define CONFIG_SYS_FSL_ERRATUM_USB138 +#define CONFIG_SYS_FSL_ERRATUM_USB14 #define CONFIG_SYS_FSL_ERRATUM_DDR_A003 #define CONFIG_SYS_FSL_ERRATUM_DDR_A003474 #define CONFIG_SYS_FSL_ERRATUM_A004699 @@ -490,7 +496,6 @@ #define CONFIG_NUM_DDR_CONTROLLERS 1 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_NAND_FSL_IFC -#define CONFIG_SYS_FSL_ERRATUM_IFC_A003399 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #elif defined(CONFIG_BSC9132) @@ -503,7 +508,6 @@ #define CONFIG_NUM_DDR_CONTROLLERS 2 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_NAND_FSL_IFC -#define CONFIG_SYS_FSL_ERRATUM_IFC_A003399 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define CONFIG_SYS_FSL_ESDHC_P1010_BROKEN_SDCLK #define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2" @@ -560,6 +564,7 @@ #define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.4" #define CONFIG_SYS_FSL_USB1_PHY_ENABLE #define CONFIG_SYS_FSL_ERRATUM_A_004934 +#define CONFIG_SYS_FSL_ERRATUM_A005871 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 #elif defined(CONFIG_PPC_B4860) @@ -585,6 +590,7 @@ #define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 #define CONFIG_SYS_FSL_USB1_PHY_ENABLE #define CONFIG_SYS_FSL_ERRATUM_A_004934 +#define CONFIG_SYS_FSL_ERRATUM_A005871 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 #else diff --git a/arch/powerpc/include/asm/fsl_memac.h b/arch/powerpc/include/asm/fsl_memac.h index d6b60e65bc..69f95d1d1e 100644 --- a/arch/powerpc/include/asm/fsl_memac.h +++ b/arch/powerpc/include/asm/fsl_memac.h @@ -222,6 +222,10 @@ struct memac { /* IF_MODE - Interface Mode Register */ #define IF_MODE_EN_AUTO 0x00008000 /* 1 - Enable automatic speed selection */ +#define IF_MODE_SETSP_100M 0x00000000 /* 00 - 100Mbps RGMII */ +#define IF_MODE_SETSP_10M 0x00002000 /* 01 - 10Mbps RGMII */ +#define IF_MODE_SETSP_1000M 0x00004000 /* 10 - 1000Mbps RGMII */ +#define IF_MODE_SETSP_MASK 0x00006000 /* setsp mask bits */ #define IF_MODE_XGMII 0x00000000 /* 00- XGMII(10) interface mode */ #define IF_MODE_GMII 0x00000002 /* 10- GMII interface mode */ #define IF_MODE_MASK 0x00000003 /* mask for mode interface mode */ diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h index 4eb3f79230..baaa9fee53 100644 --- a/arch/powerpc/include/asm/immap_85xx.h +++ b/arch/powerpc/include/asm/immap_85xx.h @@ -2914,7 +2914,8 @@ struct ccsr_pman { #define CONFIG_SYS_MPC85xx_IFC_OFFSET 0x124000 #define CONFIG_SYS_MPC85xx_GPIO_OFFSET 0x130000 #define CONFIG_SYS_FSL_CORENET_RMAN_OFFSET 0x1e0000 -#ifdef CONFIG_SYS_FSL_QORIQ_CHASSIS2 +#if defined(CONFIG_SYS_FSL_QORIQ_CHASSIS2) && !defined(CONFIG_PPC_B4860)\ + && !defined(CONFIG_PPC_B4420) #define CONFIG_SYS_MPC85xx_PCIE1_OFFSET 0x240000 #define CONFIG_SYS_MPC85xx_PCIE2_OFFSET 0x250000 #define CONFIG_SYS_MPC85xx_PCIE3_OFFSET 0x260000 @@ -3160,4 +3161,13 @@ struct ccsr_cluster_l2 { #define CONFIG_SYS_FSL_CLUSTER_1_L2 \ (CONFIG_SYS_IMMR + CONFIG_SYS_FSL_CLUSTER_1_L2_OFFSET) #endif /* CONFIG_SYS_FSL_QORIQ_CHASSIS2 */ + +#define CONFIG_SYS_DCSR_DCFG_OFFSET 0X20000 +struct dcsr_dcfg_regs { + u8 res_0[0x520]; + u32 ecccr1; +#define DCSR_DCFG_ECC_DISABLE_USB1 0x00008000 +#define DCSR_DCFG_ECC_DISABLE_USB2 0x00004000 + u8 res_524[0x1000 - 0x524]; /* 0x524 - 0x1000 */ +}; #endif /*__IMMAP_85xx__*/ diff --git a/board/freescale/b4860qds/tlb.c b/board/freescale/b4860qds/tlb.c index 373cb7848c..6d634bf690 100644 --- a/board/freescale/b4860qds/tlb.c +++ b/board/freescale/b4860qds/tlb.c @@ -111,8 +111,6 @@ struct fsl_e_tlb_entry tlb_table[] = { #ifdef CONFIG_SYS_NAND_BASE /* * *I*G - NAND - * entry 14 and 15 has been used hard coded, they will be disabled - * in cpu_init_f, so we use entry 16 for nand. */ SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, @@ -122,6 +120,23 @@ struct fsl_e_tlb_entry tlb_table[] = { MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 12, BOOKE_PAGESZ_4K, 1), + /* + * *I*G - SRIO + * entry 14 and 15 has been used hard coded, they will be disabled + * in cpu_init_f, so we use entry 16 for SRIO2. + */ +#ifdef CONFIG_SYS_SRIO1_MEM_PHYS + /* *I*G* - SRIO1 */ + SET_TLB_ENTRY(1, CONFIG_SYS_SRIO1_MEM_VIRT, CONFIG_SYS_SRIO1_MEM_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 13, BOOKE_PAGESZ_256M, 1), +#endif +#ifdef CONFIG_SYS_SRIO2_MEM_PHYS + /* *I*G* - SRIO2 */ + SET_TLB_ENTRY(1, CONFIG_SYS_SRIO2_MEM_VIRT, CONFIG_SYS_SRIO2_MEM_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 16, BOOKE_PAGESZ_256M, 1), +#endif }; int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile index 75725b49ad..72bb56cac4 100644 --- a/board/freescale/common/Makefile +++ b/board/freescale/common/Makefile @@ -33,10 +33,14 @@ COBJS-$(CONFIG_FSL_CADMUS) += cadmus.o COBJS-$(CONFIG_FSL_VIA) += cds_via.o COBJS-$(CONFIG_FMAN_ENET) += fman.o COBJS-$(CONFIG_FSL_PIXIS) += pixis.o +ifndef CONFIG_SPL_BUILD COBJS-$(CONFIG_FSL_NGPIXIS) += ngpixis.o +endif COBJS-$(CONFIG_FSL_QIXIS) += qixis.o COBJS-$(CONFIG_PQ_MDS_PIB) += pq-mds-pib.o +ifndef CONFIG_SPL_BUILD COBJS-$(CONFIG_ID_EEPROM) += sys_eeprom.o +endif COBJS-$(CONFIG_FSL_SGMII_RISER) += sgmii_riser.o ifndef CONFIG_RAMBOOT_PBL COBJS-$(CONFIG_FSL_FIXED_MMC_LOCATION) += sdhc_boot.o @@ -48,7 +52,9 @@ COBJS-$(CONFIG_MPC8555CDS) += cds_pci_ft.o COBJS-$(CONFIG_MPC8536DS) += ics307_clk.o COBJS-$(CONFIG_MPC8572DS) += ics307_clk.o +ifndef CONFIG_SPL_BUILD COBJS-$(CONFIG_P1022DS) += ics307_clk.o +endif COBJS-$(CONFIG_P2020DS) += ics307_clk.o COBJS-$(CONFIG_P3041DS) += ics307_clk.o COBJS-$(CONFIG_P4080DS) += ics307_clk.o diff --git a/board/freescale/common/cds_pci_ft.c b/board/freescale/common/cds_pci_ft.c index 8a09f99cc4..32233db405 100644 --- a/board/freescale/common/cds_pci_ft.c +++ b/board/freescale/common/cds_pci_ft.c @@ -31,7 +31,8 @@ static void cds_pci_fixup(void *blob) int node; const char *path; int len, slot, i; - u32 *map = NULL; + u32 *map = NULL, *piccells = NULL; + int off, cells; node = fdt_path_offset(blob, "/aliases"); if (node >= 0) { @@ -41,6 +42,25 @@ static void cds_pci_fixup(void *blob) if (node >= 0) { map = fdt_getprop_w(blob, node, "interrupt-map", &len); } + /* Each item in "interrupt-map" property is translated with + * following cells: + * PCI #address-cells, PCI #interrupt-cells, + * PIC address, PIC #address-cells, PIC #interrupt-cells. + */ + cells = fdt_getprop_u32_default(blob, path, "#address-cells", 1); + cells += fdt_getprop_u32_default(blob, path, "#interrupt-cells", 1); + off = fdt_node_offset_by_phandle(blob, fdt32_to_cpu(*(map+cells))); + if (off <= 0) + return; + cells += 1; + piccells = (u32 *)fdt_getprop(blob, off, "#address-cells", NULL); + if (piccells == NULL) + return; + cells += *piccells; + piccells = (u32 *)fdt_getprop(blob, off, "#interrupt-cells", NULL); + if (piccells == NULL) + return; + cells += *piccells; } } @@ -49,12 +69,12 @@ static void cds_pci_fixup(void *blob) slot = get_pci_slot(); - for (i=0;i<len;i+=7) { + for (i=0;i<len;i+=cells) { /* We rotate the interrupt pins so that the mapping * changes depending on the slot the carrier card is in. */ map[3] = ((map[3] + slot - 2) % 4) + 1; - map+=7; + map+=cells; } } } diff --git a/board/freescale/p1010rdb/p1010rdb.c b/board/freescale/p1010rdb/p1010rdb.c index 11e2e8ae48..0c30d76345 100644 --- a/board/freescale/p1010rdb/p1010rdb.c +++ b/board/freescale/p1010rdb/p1010rdb.c @@ -217,7 +217,7 @@ void fdt_del_flexcan(void *blob) int nodeoff = 0; while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, - "fsl,flexcan-v1.0")) >= 0) { + "fsl,p1010-flexcan")) >= 0) { fdt_del_node(blob, nodeoff); } } diff --git a/board/freescale/p1022ds/Makefile b/board/freescale/p1022ds/Makefile index c6d3418c16..0eeef05266 100644 --- a/board/freescale/p1022ds/Makefile +++ b/board/freescale/p1022ds/Makefile @@ -11,12 +11,26 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).o +MINIMAL= + +ifdef CONFIG_SPL_BUILD +ifdef CONFIG_SPL_INIT_MINIMAL +MINIMAL=y +endif +endif + +ifdef MINIMAL + +COBJS-y += spl_minimal.o tlb.o law.o + +else COBJS-y += $(BOARD).o COBJS-y += ddr.o COBJS-y += law.o COBJS-y += tlb.o COBJS-$(CONFIG_FSL_DIU_FB) += diu.o +endif SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) OBJS := $(addprefix $(obj),$(COBJS-y)) diff --git a/board/freescale/p1022ds/law.c b/board/freescale/p1022ds/law.c index b23b8f9af5..c4398ddff9 100644 --- a/board/freescale/p1022ds/law.c +++ b/board/freescale/p1022ds/law.c @@ -16,6 +16,7 @@ struct law_entry law_table[] = { SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC), SET_LAW(PIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_32K, LAW_TRGT_IF_LBC), }; int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/p1022ds/spl_minimal.c b/board/freescale/p1022ds/spl_minimal.c new file mode 100644 index 0000000000..8d12fa6c7d --- /dev/null +++ b/board/freescale/p1022ds/spl_minimal.c @@ -0,0 +1,129 @@ +/* + * Copyright 2011 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include <common.h> +#include <ns16550.h> +#include <asm/io.h> +#include <nand.h> +#include <asm/fsl_law.h> +#include <asm/fsl_ddr_sdram.h> + + +/* + * Fixed sdram init -- doesn't use serial presence detect. + */ +void sdram_init(void) +{ + volatile ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR; + + __raw_writel(CONFIG_SYS_DDR_CS0_BNDS, &ddr->cs0_bnds); + __raw_writel(CONFIG_SYS_DDR_CS0_CONFIG, &ddr->cs0_config); +#if CONFIG_CHIP_SELECTS_PER_CTRL > 1 + __raw_writel(CONFIG_SYS_DDR_CS1_BNDS, &ddr->cs1_bnds); + __raw_writel(CONFIG_SYS_DDR_CS1_CONFIG, &ddr->cs1_config); +#endif + __raw_writel(CONFIG_SYS_DDR_TIMING_3, &ddr->timing_cfg_3); + __raw_writel(CONFIG_SYS_DDR_TIMING_0, &ddr->timing_cfg_0); + __raw_writel(CONFIG_SYS_DDR_TIMING_1, &ddr->timing_cfg_1); + __raw_writel(CONFIG_SYS_DDR_TIMING_2, &ddr->timing_cfg_2); + + __raw_writel(CONFIG_SYS_DDR_CONTROL_2, &ddr->sdram_cfg_2); + __raw_writel(CONFIG_SYS_DDR_MODE_1, &ddr->sdram_mode); + __raw_writel(CONFIG_SYS_DDR_MODE_2, &ddr->sdram_mode_2); + + __raw_writel(CONFIG_SYS_DDR_INTERVAL, &ddr->sdram_interval); + __raw_writel(CONFIG_SYS_DDR_DATA_INIT, &ddr->sdram_data_init); + __raw_writel(CONFIG_SYS_DDR_CLK_CTRL, &ddr->sdram_clk_cntl); + + __raw_writel(CONFIG_SYS_DDR_TIMING_4, &ddr->timing_cfg_4); + __raw_writel(CONFIG_SYS_DDR_TIMING_5, &ddr->timing_cfg_5); + __raw_writel(CONFIG_SYS_DDR_ZQ_CONTROL, &ddr->ddr_zq_cntl); + __raw_writel(CONFIG_SYS_DDR_WRLVL_CONTROL, &ddr->ddr_wrlvl_cntl); + + /* Set, but do not enable the memory */ + __raw_writel(CONFIG_SYS_DDR_CONTROL & ~SDRAM_CFG_MEM_EN, + &ddr->sdram_cfg); + + in_be32(&ddr->sdram_cfg); + udelay(500); + + /* Let the controller go */ + out_be32(&ddr->sdram_cfg, in_be32(&ddr->sdram_cfg) | SDRAM_CFG_MEM_EN); + in_be32(&ddr->sdram_cfg); + + set_next_law(0, CONFIG_SYS_SDRAM_SIZE_LAW, LAW_TRGT_IF_DDR_1); +} + +const static u32 sysclk_tbl[] = { + 66666000, 7499900, 83332500, 8999900, + 99999000, 11111000, 12499800, 13333200 +}; + +void board_init_f(ulong bootflag) +{ + int px_spd; + u32 plat_ratio, sys_clk, bus_clk; + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + + /* for FPGA */ + set_lbc_br(2, CONFIG_SYS_BR2_PRELIM); + set_lbc_or(2, CONFIG_SYS_OR2_PRELIM); + + /* initialize selected port with appropriate baud rate */ + px_spd = in_8((unsigned char *)(PIXIS_BASE + PIXIS_SPD)); + sys_clk = sysclk_tbl[px_spd & PIXIS_SPD_SYSCLK_MASK]; + plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO; + bus_clk = sys_clk * plat_ratio / 2; + + NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, + bus_clk / 16 / CONFIG_BAUDRATE); + + puts("\nNAND boot... "); + + /* Initialize the DDR3 */ + sdram_init(); + + /* copy code to RAM and jump to it - this should not return */ + /* NOTE - code has to be copied out of NAND buffer before + * other blocks can be read. + */ + relocate_code(CONFIG_SPL_RELOC_STACK, 0, + CONFIG_SPL_RELOC_TEXT_BASE); +} + +void board_init_r(gd_t *gd, ulong dest_addr) +{ + nand_boot(); +} + +void putc(char c) +{ + if (c == '\n') + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r'); + + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c); +} + +void puts(const char *str) +{ + while (*str) + putc(*str++); +} diff --git a/board/freescale/p1022ds/tlb.c b/board/freescale/p1022ds/tlb.c index 71e71f7070..3acc44912d 100644 --- a/board/freescale/p1022ds/tlb.c +++ b/board/freescale/p1022ds/tlb.c @@ -41,6 +41,7 @@ struct fsl_e_tlb_entry tlb_table[] = { MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 1, BOOKE_PAGESZ_1M, 1), +#ifndef CONFIG_SPL_BUILD /* W**G* - Flash/promjet, localbus */ /* This will be changed to *I*G* after relocation to RAM. */ SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, @@ -67,24 +68,31 @@ struct fsl_e_tlb_entry tlb_table[] = { SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_IO_VIRT, CONFIG_SYS_PCIE3_IO_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 6, BOOKE_PAGESZ_256K, 1), +#endif SET_TLB_ENTRY(1, PIXIS_BASE, PIXIS_BASE_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 7, BOOKE_PAGESZ_4K, 1), -#ifdef CONFIG_SYS_RAMBOOT - /* *I*G - eSDHC/eSPI/NAND boot */ +#if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_SPL) + /* **** - eSDHC/eSPI/NAND boot */ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, MAS3_SX|MAS3_SW|MAS3_SR, 0, 0, 8, BOOKE_PAGESZ_1G, 1), - - /* map the second 1G */ + /* **** - eSDHC/eSPI/NAND boot - second 1GB of memory */ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + MAS3_SX|MAS3_SW|MAS3_SR, 0, 0, 9, BOOKE_PAGESZ_1G, 1), #endif -# + +#ifdef CONFIG_SYS_NAND_BASE + /* *I*G - NAND */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_16K, 1), +#endif + }; int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c index 5b5b86c822..2e0e0c73aa 100644 --- a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c +++ b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c @@ -55,6 +55,13 @@ #define GPIO_SLIC_PIN 30 #define GPIO_SLIC_DATA (1 << (31 - GPIO_SLIC_PIN)) +#if defined(CONFIG_P1021RDB) && !defined(CONFIG_SYS_RAMBOOT) +#define GPIO_DDR_RST_PORT 1 +#define GPIO_DDR_RST_PIN 8 +#define GPIO_DDR_RST_DATA (1 << (31 - GPIO_DDR_RST_PIN)) + +#define GPIO_2BIT_MASK (0x3 << (32 - (GPIO_DDR_RST_PIN + 1) * 2)) +#endif #if defined(CONFIG_P1025RDB) || defined(CONFIG_P1021RDB) #define PCA_IOPORT_I2C_ADDR 0x23 @@ -67,7 +74,7 @@ const qe_iop_conf_t qe_iop_conf_tab[] = { /* GPIO */ {1, 1, 2, 0, 0}, /* GPIO7/PB1 - LOAD_DEFAULT_N */ -#if 0 +#if defined(CONFIG_P1021RDB) && !defined(CONFIG_SYS_RAMBOOT) {1, 8, 1, 1, 0}, /* GPIO10/PB8 - DDR_RST */ #endif {0, 15, 1, 0, 0}, /* GPIO11/A15 - WDI */ @@ -159,6 +166,16 @@ void board_gpio_init(void) ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); par_io_t *par_io = (par_io_t *) &(gur->qe_par_io); +#if defined(CONFIG_P1021RDB) && !defined(CONFIG_SYS_RAMBOOT) + /* reset DDR3 */ + setbits_be32(&par_io[GPIO_DDR_RST_PORT].cpdat, GPIO_DDR_RST_DATA); + udelay(1000); + clrbits_be32(&par_io[GPIO_DDR_RST_PORT].cpdat, GPIO_DDR_RST_DATA); + udelay(1000); + setbits_be32(&par_io[GPIO_DDR_RST_PORT].cpdat, GPIO_DDR_RST_DATA); + /* disable CE_PB8 */ + clrbits_be32(&par_io[GPIO_DDR_RST_PORT].cpdir1, GPIO_2BIT_MASK); +#endif /* Enable VSC7385 switch */ setbits_be32(&par_io[GPIO_GETH_SW_PORT].cpdat, GPIO_GETH_SW_DATA); @@ -421,6 +438,8 @@ void ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; + const char *soc_usb_compat = "fsl-usb2-dr"; + int err, usb1_off, usb2_off; ft_cpu_setup(blob, bd); @@ -442,5 +461,50 @@ void ft_board_setup(void *blob, bd_t *bd) #if defined(CONFIG_HAS_FSL_DR_USB) fdt_fixup_dr_usb(blob, bd); #endif + +#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH) + /* Delete eLBC node as it is muxed with USB2 controller */ + if (hwconfig("usb2")) { + const char *soc_elbc_compat = "fsl,p1020-elbc"; + int off = fdt_node_offset_by_compatible(blob, -1, + soc_elbc_compat); + if (off < 0) { + printf("WARNING: could not find compatible node %s: %s.\n", + soc_elbc_compat, + fdt_strerror(off)); + return; + } + err = fdt_del_node(blob, off); + if (err < 0) { + printf("WARNING: could not remove %s: %s.\n", + soc_elbc_compat, fdt_strerror(err)); + } + return; + } +#endif + +/* Delete USB2 node as it is muxed with eLBC */ + usb1_off = fdt_node_offset_by_compatible(blob, -1, + soc_usb_compat); + if (usb1_off < 0) { + printf("WARNING: could not find compatible node %s: %s.\n", + soc_usb_compat, + fdt_strerror(usb1_off)); + return; + } + usb2_off = fdt_node_offset_by_compatible(blob, usb1_off, + soc_usb_compat); + if (usb2_off < 0) { + printf("WARNING: could not find compatible node %s: %s.\n", + soc_usb_compat, + fdt_strerror(usb2_off)); + return; + } + err = fdt_del_node(blob, usb2_off); + if (err < 0) { + printf("WARNING: could not remove %s: %s.\n", + soc_usb_compat, fdt_strerror(err)); + } + } #endif diff --git a/board/freescale/p1_p2_rdb_pc/spl_minimal.c b/board/freescale/p1_p2_rdb_pc/spl_minimal.c index 09019e98af..e2bfb0d63d 100644 --- a/board/freescale/p1_p2_rdb_pc/spl_minimal.c +++ b/board/freescale/p1_p2_rdb_pc/spl_minimal.c @@ -81,6 +81,8 @@ void board_init_f(ulong bootflag) ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; #ifndef CONFIG_QE ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR); +#elif defined(CONFIG_P1021RDB) + par_io_t *par_io = (par_io_t *)&(gur->qe_par_io); #endif /* initialize selected port with appropriate baud rate */ @@ -102,6 +104,19 @@ void board_init_f(ulong bootflag) __raw_writel(0x00200000, &pgpio->gpdat); udelay(1000); __raw_writel(0x00000000, &pgpio->gpdir); +#elif defined(CONFIG_P1021RDB) + /* init DDR3 reset signal CE_PB8 */ + out_be32(&par_io[1].cpdir1, 0x00004000); + out_be32(&par_io[1].cpodr, 0x00800000); + out_be32(&par_io[1].cppar1, 0x00000000); + /* reset DDR3 */ + out_be32(&par_io[1].cpdat, 0x00800000); + udelay(1000); + out_be32(&par_io[1].cpdat, 0x00000000); + udelay(1000); + out_be32(&par_io[1].cpdat, 0x00800000); + /* disable the CE_PB8 */ + out_be32(&par_io[1].cpdir1, 0x00000000); #endif #ifndef CONFIG_SYS_INIT_L2_ADDR diff --git a/boards.cfg b/boards.cfg index 8b7933ffbb..5d78064979 100644 --- a/boards.cfg +++ b/boards.cfg @@ -811,6 +811,8 @@ P1021RDB-PC_NAND powerpc mpc85xx p1_p2_rdb_pc freesca P1021RDB-PC_SDCARD powerpc mpc85xx p1_p2_rdb_pc freescale - p1_p2_rdb_pc:P1021RDB,SDCARD P1021RDB-PC_SPIFLASH powerpc mpc85xx p1_p2_rdb_pc freescale - p1_p2_rdb_pc:P1021RDB,SPIFLASH P1022DS powerpc mpc85xx p1022ds freescale +P1022DS_NAND powerpc mpc85xx p1022ds freescale - P1022DS:NAND +P1022DS_36BIT_NAND powerpc mpc85xx p1022ds freescale - P1022DS:36BIT,NAND P1022DS_SPIFLASH powerpc mpc85xx p1022ds freescale - P1022DS:SPIFLASH P1022DS_36BIT_SPIFLASH powerpc mpc85xx p1022ds freescale - P1022DS:36BIT,SPIFLASH P1022DS_SDCARD powerpc mpc85xx p1022ds freescale - P1022DS:SDCARD diff --git a/doc/README.p1010rdb b/doc/README.p1010rdb new file mode 100644 index 0000000000..dee63d713a --- /dev/null +++ b/doc/README.p1010rdb @@ -0,0 +1,199 @@ +Overview +========= +The P1010RDB is a Freescale reference design board that hosts the P1010 SoC. + +The P1010 is a cost-effective, low-power, highly integrated host processor +based on a Power Architecture e500v2 core (maximum core frequency 800/1000 MHz), +that addresses the requirements of several routing, gateways, storage, consumer, +and industrial applications. Applications of interest include the main CPUs and +I/O processors in network attached storage (NAS), the voice over IP (VoIP) +router/gateway, and wireless LAN (WLAN) and industrial controllers. + +The P1010RDB board features are as follows: +Memory subsystem: + - 1Gbyte unbuffered DDR3 SDRAM discrete devices (32-bit bus) + - 32 Mbyte NOR flash single-chip memory + - 32 Mbyte NAND flash memory + - 256 Kbit M24256 I2C EEPROM + - 16 Mbyte SPI memory + - I2C Board EEPROM 128x8 bit memory + - SD/MMC connector to interface with the SD memory card +Interfaces: + - PCIe: + - Lane0: x1 mini-PCIe slot + - Lane1: x1 PCIe standard slot + - SATA: + - 1 internal SATA connector to 2.5" 160G SATA2 HDD + - 1 eSATA connector to rear panel + - 10/100/1000 BaseT Ethernet ports: + - eTSEC1, RGMII: one 10/100/1000 port using Vitesse VSC8641XKO + - eTSEC2, SGMII: one 10/100/1000 port using Vitesse VSC8221 + - eTSEC3, SGMII: one 10/100/1000 port using Vitesse VSC8221 + - USB 2.0 port: + - x1 USB2.0 port: via an ULPI PHY to micro-AB connector + - x1 USB2.0 poort via an internal PHY to micro-AB connector + - FlexCAN ports: + - x2 DB-9 female connectors for FlexCAN bus(revision 2.0B) + interface; + - DUART interface: + - DUART interface: supports two UARTs up to 115200 bps for + console display + - J45 connectors are used for these 2 UART ports. + - TDM + - 2 FXS ports connected via an external SLIC to the TDM + interface. SLIC is controllled via SPI. + - 1 FXO port connected via a relay to FXS for switchover to + POTS +Board connectors: + - Mini-ITX power supply connector + - JTAG/COP for debugging +IEEE Std. 1588 signals for test and measurement +Real-time clock on I2C bus +POR + - support critical POR setting changed via switch on board +PCB + - 6-layer routing (4-layer signals, 2-layer power and ground) + + +Serial Port Configuration on P1010RDB +===================================== +Configure the serial port of the attached computer with the following values: + -Data rate: 115200 bps + -Number of data bits: 8 + -Parity: None + -Number of Stop bits: 1 + -Flow Control: Hardware/None + + +Settings of DIP-switch +====================== + SW4[1:4]= 1111 and SW6[4]=0 for boot from 16bit NOR flash + SW4[1:4]= 1000 and SW6[4]=1 for boot from 8bit NAND flash + SW4[1:4]= 0110 and SW6[4]=0 for boot from SPI flash +Note: 1 stands for 'on', 0 stands for 'off' + + +Setting of hwconfig +=================== +If FlexCAN or TDM is needed, please set "fsl_p1010mux:tdm_can=can" or +"fsl_p1010mux:tdm_can=tdm" explicitly in u-booot prompt as below for example: +setenv hwconfig "fsl_p1010mux:tdm_can=tdm;usb1:dr_mode=host,phy_type=utmi" +By default, don't set fsl_p1010mux:tdm_can, in this case, spi chip selection +is set to spi-flash instead of to SLIC/TDM/DAC and tdm_can_sel is set to TDM +instead of to CAN/UART1. + + +Build and burn u-boot to NOR flash +================================== +1. Build u-boot.bin image + export ARCH=powerpc + export CROSS_COMPILE=/your_path/powerpc-linux-gnu- + make P1010RDB_NOR + +2. Burn u-boot.bin into NOR flash + => tftp $loadaddr $uboot + => protect off eff80000 +$filesize + => erase eff80000 +$filesize + => cp.b $loadaddr eff80000 $filesize + +3. Check SW4[1:4]= 1111 and SW6[4]=0, then power on. + + +Alternate NOR bank +============================ +1. Burn u-boot.bin into alternate NOR bank + => tftp $loadaddr $uboot + => protect off eef80000 +$filesize + => erase eef80000 +$filesize + => cp.b $loadaddr eef80000 $filesize + +2. Switch to alternate NOR bank + => mw.b ffb00009 1 + => reset + or set SW1[8]= ON + +SW1[8]= OFF: Upper bank used for booting start +SW1[8]= ON: Lower bank used for booting start +CPLD NOR bank selection register address 0xFFB00009 Bit[0]: +0 - boot from upper 4 sectors +1 - boot from lower 4 sectors + + +Build and burn u-boot to NAND flash +=================================== +1. Build u-boot.bin image + export ARCH=powerpc + export CROSS_COMPILE=/your_path/powerpc-linux-gnu- + make P1010RDB_NAND + +2. Burn u-boot-nand.bin into NAND flash + => tftp $loadaddr $uboot-nand + => nand erase 0 $filesize + => nand write $loadaddr 0 $filesize + +3. Check SW4[1:4]= 1000 and SW6[4]=1, then power on. + + + +Build and burn u-boot to SPI flash +================================== +1. Build u-boot-spi.bin image + make P1010RDB_SPIFLASH_config; make + Boot up kernel with rootfs.ext2.gz.uboot.p1010rdb + Download u-boot.bin to linux and you can find some config files + under /usr/share such as config_xx.dat. Do below command: + boot_format config_ddr3_1gb_p1010rdb_800M.dat u-boot.bin -spi \ + u-boot-spi.bin + to generate u-boot-spi.bin. + +2. Burn u-boot-spi.bin into SPI flash + => tftp $loadaddr $uboot-spi + => sf erase 0 100000 + => sf write $loadaddr 0 $filesize + +3. Check SW4[1:4]= 0110 and SW6[4]=0, then power on. + + + +CPLD POR setting registers +========================== +1. Set POR switch selection register (addr 0xFFB00011) to 0. +2. Write CPLD POR registers (BCSR0~BCSR3, addr 0xFFB00014~0xFFB00017) with + proper values. + If change boot ROM location to NOR or NAND flash, need write the IFC_CS0 + switch command by I2C. +3. Send reset command. + After reset, the new POR setting will be implemented. + +Two examples are given in below: +Switch from NOR to NAND boot with default frequency: + => i2c dev 0 + => i2c mw 18 1 f9 + => i2c mw 18 3 f0 + => mw.b ffb00011 0 + => mw.b ffb00017 1 + => reset +Switch from NAND to NOR boot with Core/CCB/DDR (800/400/667 MHz): + => i2c dev 0 + => i2c mw 18 1 f1 + => i2c mw 18 3 f0 + => mw.b ffb00011 0 + => mw.b ffb00014 2 + => mw.b ffb00015 5 + => mw.b ffb00016 3 + => mw.b ffb00017 f + => reset + + + +Boot Linux from network using TFTP on P1010RDB +============================================== +Place uImage, p1010rdb.dtb and rootfs files in the TFTP disk area. + => tftp 1000000 uImage + => tftp 2000000 p1010rdb.dtb + => tftp 3000000 rootfs.ext2.gz.uboot.p1010rdb + => bootm 1000000 3000000 2000000 + + +Please contact your local field applications engineer or sales representative +to obtain related documents, such as P1010-RDB User Guide for details. diff --git a/doc/README.ramboot-ppc85xx b/doc/README.ramboot-ppc85xx new file mode 100644 index 0000000000..8ed45fb46d --- /dev/null +++ b/doc/README.ramboot-ppc85xx @@ -0,0 +1,102 @@ + RAMBOOT for MPC85xx Platforms + ============================== + +RAMBOOT literally means boot from DDR. But since DDR is volatile memory some +pre-mechanism is required to load the DDR with the bootloader binary. +- In case of SD and SPI boot this is done by BootROM code inside the chip + itself. +- In case of NAND boot FCM supports loading initial 4K code from NAND flash + which can initialize the DDR and get the complete bootloader copied to DDR. + +In addition to the above there could be some more methods to initialize the DDR +and load it manually. +Two of them are described below.There is also an explanation as to where these +methods could be handy. +1. Load the RAM based bootloader onto DDR via JTAG/BDI interface. And then + execute the bootloader from DDR. + This may be handy in the following cases: + - In very early stage of platform bringup where other boot options are not + functional because of various reasons. + - In case the support to program the flashes on the board is not available. + +2. Load the RAM based bootloader onto DDR using already existing bootloader on + the board.And then execute the bootloader from DDR. + Some usecases where this may be used: + - While developing some new feature of u-boot, for example USB driver or + SPI driver. + Suppose the board already has a working bootloader on it. And you would + prefer to keep it intact, at the same time want to test your bootloader. + In this case you can get your test bootloader binary into DDR via tftp + for example. Then execute the test bootloader. + - Suppose a platform already has a propreitery bootloader which does not + support for example AMP boot. In this case also RAM boot loader can be + utilized. + + So basically when the original bootloader is required to be kept intact + RAM based bootloader can offer an updated bootloader on the system. + +Both the above Bootloaders are slight variants of SDcard or SPI Flash +bootloader or for that matter even NAND bootloader. +All of them define CONFIG_SYS_RAMBOOT. +The main difference among all of them is the way the pre-environment is getting +configured and who is doing that. +- In case of SD card and SPI flash bootloader this is done by On Chip BootROM inside the Si itself. +- In case of NAND boot SPL/TPL code does it with some support from Si itself. +- In case of the pure RAM based bootloaders we have to do it by JTAG manually or already existing bootloader. + +How to use them: +1. Using JTAG + Boot up in core hold off mode or stop the core after reset using JTAG + interface. + Preconfigure DDR/L2SRAM through JTAG interface. + - setup DDR controller registers. + - setup DDR LAWs + - setup DDR TLB + Load the RAM based boot loader to the proper location in DDR/L2SRAM. + set up IAR (Instruction counter properly) + Enable the core to execute. + +2. Using already existing bootloader. + get the rambased boot loader binary into DDR/L2SRAM via tftp. + execute the RAM based bootloader. + => tftp 11000000 u-boot-ram.bin + => go 1107f000 + +Please note that L2SRAM can also be used instead of DDR if the SOC has +sufficient size of L2SRAM. + +Necessary Code changes Required: +===================================== +Please note that below mentioned changes are for 85xx platforms. +They have been tested on P1020/P2020/P1010 RDB. + +The main difference between the above two methods from technical perspective is +that in 1st case SOC is just out of reset so it is in default configuration. +(CCSRBAR is at 0xff700000). +In the 2nd case bootloader has already re-located CCSRBAR to 0xffe00000 + +1. File name-> boards.cfg + There can be added specific Make options for RAMBoot. We can keep different + options for the two cases mentioned above. + for example + P1020RDB_JTAG_RAMBOOT and P1020RDB_GO_RAMBOOT. + +2. platform config file + for example include/configs/P1_P2_RDB.h + + #ifdef CONFIG_RAMBOOT + #define CONFIG_SDCARD + #endif + + This will finally use the CONFIG_SYS_RAMBOOT. + +3. File name-> arch/powerpc/include/asm/config_mpc85xx.h + In the section of the particular SOC, for example P1020, + + #if defined(CONFIG_GO) + #define CONFIG_SYS_CCSRBAR_DEFAULT 0xffe00000 + #else + #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 + #endif + +For JTAG RAMBOOT this is not required because CCSRBAR is at ff700000. diff --git a/drivers/net/fm/memac.c b/drivers/net/fm/memac.c index 32c7054e35..d3eee248ac 100644 --- a/drivers/net/fm/memac.c +++ b/drivers/net/fm/memac.c @@ -112,6 +112,23 @@ static void memac_set_interface_mode(struct fsl_enet_mac *mac, /* Enable automatic speed selection */ if_mode |= IF_MODE_EN_AUTO; + if (type == PHY_INTERFACE_MODE_RGMII) { + if_mode &= ~IF_MODE_EN_AUTO; + if_mode &= ~IF_MODE_SETSP_MASK; + switch (speed) { + case SPEED_1000: + if_mode |= IF_MODE_SETSP_1000M; + break; + case SPEED_100: + if_mode |= IF_MODE_SETSP_100M; + break; + case SPEED_10: + if_mode |= IF_MODE_SETSP_10M; + default: + break; + } + } + debug(" %s, if_mode = %x\n", __func__, if_mode); debug(" %s, if_status = %x\n", __func__, if_status); out_be32(®s->if_mode, if_mode); diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h index 14d597aad2..b282e7bc47 100644 --- a/include/configs/P1022DS.h +++ b/include/configs/P1022DS.h @@ -34,6 +34,29 @@ #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc #endif +#define CONFIG_NAND_FSL_ELBC + +#ifdef CONFIG_NAND +#define CONFIG_SPL +#define CONFIG_SPL_INIT_MINIMAL +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_MINIMAL +#define CONFIG_SPL_FLUSH_IMAGE +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" + +#define CONFIG_SYS_TEXT_BASE 0x00201000 +#define CONFIG_SPL_TEXT_BASE 0xfffff000 +#define CONFIG_SPL_MAX_SIZE (4 * 1024) +#define CONFIG_SPL_RELOC_TEXT_BASE 0x00100000 +#define CONFIG_SPL_RELOC_STACK 0x00100000 +#define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) + CONFIG_SPL_MAX_SIZE) +#define CONFIG_SYS_NAND_U_BOOT_DST (0x00200000 - CONFIG_SPL_MAX_SIZE) +#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0 +#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" +#endif + /* High Level Configuration Options */ #define CONFIG_BOOKE /* BOOKE */ #define CONFIG_E500 /* BOOKE e500 family */ @@ -84,6 +107,13 @@ #define CONFIG_SYS_CCSRBAR 0xffe00000 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR +/* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k + SPL code*/ +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE +#endif + + /* DDR Setup */ #define CONFIG_DDR_SPD #define CONFIG_VERY_BIG_RAM @@ -105,6 +135,30 @@ #define CONFIG_SYS_SPD_BUS_NUM 1 #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ +/* These are used when DDR doesn't use SPD. */ +#define CONFIG_SYS_SDRAM_SIZE 2048 +#define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_2G +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003F +#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202 +#define CONFIG_SYS_DDR_CS1_BNDS 0x0040007F +#define CONFIG_SYS_DDR_CS1_CONFIG 0x80014202 +#define CONFIG_SYS_DDR_TIMING_3 0x00010000 +#define CONFIG_SYS_DDR_TIMING_0 0x40110104 +#define CONFIG_SYS_DDR_TIMING_1 0x5c5bd746 +#define CONFIG_SYS_DDR_TIMING_2 0x0fa8d4ca +#define CONFIG_SYS_DDR_MODE_1 0x00441221 +#define CONFIG_SYS_DDR_MODE_2 0x00000000 +#define CONFIG_SYS_DDR_INTERVAL 0x0a280100 +#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef +#define CONFIG_SYS_DDR_CLK_CTRL 0x02800000 +#define CONFIG_SYS_DDR_CONTROL 0xc7000008 +#define CONFIG_SYS_DDR_CONTROL_2 0x24401041 +#define CONFIG_SYS_DDR_TIMING_4 0x00220001 +#define CONFIG_SYS_DDR_TIMING_5 0x02401400 +#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 +#define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8675f608 + + /* * Memory map * @@ -118,6 +172,7 @@ * Localbus non-cacheable * 0xe000_0000 0xe80f_ffff Promjet/free 128M non-cacheable * 0xe800_0000 0xefff_ffff FLASH 128M non-cacheable + * 0xff80_0000 0xff80_7fff NAND 32K non-cacheable * 0xffdf_0000 0xffdf_7fff PIXIS 32K non-cacheable TLB0 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0 * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable @@ -126,38 +181,84 @@ /* * Local Bus Definitions */ -#define CONFIG_SYS_FLASH_BASE 0xe0000000 /* start of FLASH 128M */ +#define CONFIG_SYS_FLASH_BASE 0xe8000000 /* start of FLASH 128M */ #ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull +#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe8000000ull #else #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE #endif #define CONFIG_FLASH_BR_PRELIM \ - (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000) | BR_PS_16 | BR_V) + (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V) #define CONFIG_FLASH_OR_PRELIM (OR_AM_128MB | 0xff7) +#ifdef CONFIG_NAND +#define CONFIG_SYS_BR1_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ +#define CONFIG_SYS_OR1_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ +#else #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ +#endif -#define CONFIG_SYS_BR1_PRELIM \ - (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V) -#define CONFIG_SYS_OR1_PRELIM CONFIG_FLASH_OR_PRELIM - -#define CONFIG_SYS_FLASH_BANKS_LIST \ - {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} #define CONFIG_SYS_FLASH_QUIET_TEST #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ -#define CONFIG_SYS_MAX_FLASH_BANKS 2 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 #define CONFIG_SYS_MAX_FLASH_SECT 1024 +#ifndef CONFIG_SYS_MONITOR_BASE +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE +#else #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#endif +#endif #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_CFI #define CONFIG_SYS_FLASH_EMPTY_INFO +/* Nand Flash */ +#if defined(CONFIG_NAND_FSL_ELBC) +#define CONFIG_SYS_NAND_BASE 0xff800000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_NAND_BASE_PHYS 0xfff800000ull +#else +#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE +#endif + +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE, } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND 1 +#define CONFIG_SYS_NAND_BLOCK_SIZE (256 * 1024) +#define CONFIG_ELBC_NAND_SPL_STATIC_PGSIZE + +/* NAND flash config */ +#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ + | BR_PS_8 /* Port Size = 8 bit */ \ + | BR_MS_FCM /* MSEL = FCM */ \ + | BR_V) /* valid */ +#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_32KB /* length 256K */ \ + | OR_FCM_PGS /* Large Page*/ \ + | OR_FCM_CSCT \ + | OR_FCM_CST \ + | OR_FCM_CHT \ + | OR_FCM_SCY_1 \ + | OR_FCM_TRLX \ + | OR_FCM_EHTR) +#ifdef CONFIG_NAND +#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ +#else +#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ +#endif + +#endif /* CONFIG_NAND_FSL_ELBC */ + #define CONFIG_BOARD_EARLY_INIT_F #define CONFIG_BOARD_EARLY_INIT_R #define CONFIG_MISC_INIT_R @@ -177,6 +278,8 @@ #define PIXIS_LBMAP_SWITCH 7 #define PIXIS_LBMAP_MASK 0xF0 #define PIXIS_LBMAP_ALTBANK 0x20 +#define PIXIS_SPD 0x07 +#define PIXIS_SPD_SYSCLK_MASK 0x07 #define PIXIS_ELBC_SPI_MASK 0xc0 #define PIXIS_SPI 0x80 @@ -199,6 +302,9 @@ #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) +#ifdef CONFIG_SPL_BUILD +#define CONFIG_NS16550_MIN_FUNCTIONS +#endif #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} @@ -419,7 +525,6 @@ /* * Environment */ -#ifdef CONFIG_SYS_RAMBOOT #ifdef CONFIG_RAMBOOT_SPIFLASH #define CONFIG_ENV_IS_IN_SPI_FLASH #define CONFIG_ENV_SPI_BUS 0 @@ -433,16 +538,15 @@ #define CONFIG_ENV_IS_IN_MMC #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_SYS_MMC_ENV_DEV 0 -#elif defined(CONFIG_NAND_U_BOOT) +#elif defined(CONFIG_NAND) #define CONFIG_ENV_IS_IN_NAND #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE #define CONFIG_ENV_OFFSET ((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE) #define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) -#else +#elif defined(CONFIG_SYS_RAMBOOT) #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) #define CONFIG_ENV_SIZE 0x2000 -#endif #else #define CONFIG_ENV_IS_IN_FLASH #if CONFIG_SYS_MONITOR_BASE > 0xfff80000 diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h index 3f42cd9a38..5cc9b5ab26 100644 --- a/include/configs/corenet_ds.h +++ b/include/configs/corenet_ds.h @@ -714,6 +714,7 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ "bank_intlv=cs0_cs1;" \ + "usb2:dr_mode=peripheral,phy_type=" __stringify(__USB_PHY_TYPE) ";"\ "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ "netdev=eth0\0" \ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ |
