diff options
| -rw-r--r-- | README | 28 | ||||
| -rw-r--r-- | doc/README.Modem | 72 |
2 files changed, 0 insertions, 100 deletions
@@ -1023,7 +1023,6 @@ The following options need to be configured: CONFIG_CMD_GO * the 'go' command (exec code) CONFIG_CMD_GREPENV * search environment CONFIG_CMD_HASH * calculate hash / digest - CONFIG_CMD_HWFLOW * RTS/CTS hw flow control CONFIG_CMD_I2C * I2C serial bus support CONFIG_CMD_IDE * IDE harddisk support CONFIG_CMD_IMI iminfo @@ -3720,17 +3719,6 @@ FIT uImage format: CONFIG_SPL_PAD_TO must be either 0, meaning to append the SPL payload without any padding, or >= CONFIG_SPL_MAX_SIZE. -Modem Support: --------------- - -[so far only for SMDK2400 boards] - -- Modem support enable: - CONFIG_MODEM_SUPPORT - -- RTS/CTS Flow control enable: - CONFIG_HWFLOW - - Interrupt support (PPC): There are common interrupt_init() and timer_interrupt() @@ -3744,22 +3732,6 @@ Modem Support: / other_activity_monitor it works automatically from general timer_interrupt(). -- General: - - In the target system modem support is enabled when a - specific key (key combination) is pressed during - power-on. Otherwise U-Boot will boot normally - (autoboot). The key_pressed() function is called from - board_init(). Currently key_pressed() is a dummy - function, returning 1 and thus enabling modem - initialization. - - If there are no modem init strings in the - environment, U-Boot proceed to autoboot; the - previous output (banner, info printfs) will be - suppressed, though. - - See also: doc/README.Modem Board initialization settings: ------------------------------ diff --git a/doc/README.Modem b/doc/README.Modem deleted file mode 100644 index 1613c11cad..0000000000 --- a/doc/README.Modem +++ /dev/null @@ -1,72 +0,0 @@ -How to configure modem support in U-Boot : - -1. Define modem initialization strings: ---------------------------------------- - -The modem initialization strings have following format: - - mdm_init1=<AT-command> - mdm_init2=<AT-command> - ... - -Turning off modem verbose responses with ATV0 or ATQ1 is not allowed; -U-Boot analyzes only verbose (not numeric) result codes. Modem local -command echo can be turned off (ATE0). - -2. RTS/CTS hardware flow control: ---------------------------------- - -You may wish to enable RTS/CTS hardware flow control, if the board's -UART driver supports it (see CONFIG_HWFLOW compile-time flag in -config/<board>.h). This is controlled by the 'mdm_flow_control' -environment variable: - - 'mdm_flow_control=rts/cts' - to enable RTS/CTS flow control. - 'mdm_flow_control=none ' - to disable. - - -The following are the examples using a Rockwell OEM modem -configuration: - -SAMSUNG # setenv mdm_init1 ATZ - reset the modem to - the factory defaults. -SAMSUNG # setenv mdm_init2 ATS0=1 - set modem into - answer mode. -SAMSUNG # setenv mdm_flow_control rts/cts - enable serial port - flow control -SAMSUNG # saveenv - -The example above initializes modem into answer mode to wait for the -incoming call. RTS/CTS flow control is enabled for the serial port. -(The RTS/CTS flow control is enabled by default on the modem). - - -SAMSUNG # setenv mdm_init1 ATZ -SAMSUNG # setenv mdm_init2 ATS39=0+IFC=0,0 - disable modem - RTS/CTS flow control -SAMSUNG # setenv mdm_init3 ATDT1643973 - dial out the number -SAMSUNG # setenv mdm_flow_control none -SAMSUNG # saveenv - -The example above initializes modem to dial-up connection on the -number 1643973. Flow control is disabled. - -Note that flow control must be turned both off or both on for the -board serial port and for the modem. - - -If the connection was set up successfully, the U-Boot prompt appears -on the terminal console. If not (U-Boot modem was configured for -originating the call and connection was not established) - the board -should be reset for another dial-up try. - - -Note on the SMDK2400 board: ---------------------------- - -Since the board serial ports does not have DTR signal wired, modem -should be told to ignore port DTR setting prior to connection to the -SMDK board, and this setting should be stored in modem NVRAM. For the -Rockwell OEM modem this can to be done with the following command: - -AT&D0&W |
