summaryrefslogtreecommitdiffstats
path: root/include
diff options
context:
space:
mode:
authorpekon gupta <pekon@ti.com>2014-07-22 16:03:22 +0530
committerTom Rini <trini@ti.com>2014-08-25 10:48:12 -0400
commite53ad4b445464327aebd1c5ea6260b7bb9b80ae7 (patch)
treefe5edc497d51831f96b3abdccae854033889e3c1 /include
parent3df3bc1e1dc4c38de93d66fb589565f36d9749c7 (diff)
downloadtalos-obmc-uboot-e53ad4b445464327aebd1c5ea6260b7bb9b80ae7.tar.gz
talos-obmc-uboot-e53ad4b445464327aebd1c5ea6260b7bb9b80ae7.zip
board/ti/am43xx: add support for parallel NAND
This patch adds support for NAND device connected to GPMC chip-select on following AM43xx EVM boards. am437x-gp-evm: On this board, NAND Flash signals are muxed with eMMC, thus at a time either eMMC or NAND can be enabled. Selection between eMMC and NAND is controlled by: (a) Statically using Jumper on connecter (J89) present on board. (a) If Jumper on J89 is NOT used, then selection can be dynamically controlled by driving SPI2_CS0[MUX_MODE=GPIO] pin via software: SPI2_CS0 == 0: NAND (default) SPI2_CS0 == 1: eMMC am43x-epos-evm: On this board, NAND Flash control lines are muxed with QSPI, Thus only one of the two can be used at a time. Selection is controlled by: (a) Dynamically driving following GPIO pin from software GPMC_A0(GPIO) == 0 NAND is selected (default) NAND device (MT29F4G08AB) on these boards has: - data-width=8bits - blocksize=256KB - pagesize=4KB - oobsize=224 bytes For above NAND device, ROM code expects the boot-loader to be flashed in BCH16 ECC scheme for NAND boot, So by default BCH16 ECC is enabled for AM43xx EVMs. Signed-off-by: Pekon Gupta <pekon@ti.com>
Diffstat (limited to 'include')
-rw-r--r--include/configs/am43xx_evm.h64
1 files changed, 64 insertions, 0 deletions
diff --git a/include/configs/am43xx_evm.h b/include/configs/am43xx_evm.h
index e26204025f..070782774d 100644
--- a/include/configs/am43xx_evm.h
+++ b/include/configs/am43xx_evm.h
@@ -265,4 +265,68 @@
#define CONFIG_SPL_NET_SUPPORT
#define CONFIG_SYS_RX_ETH_BUFFER 64
+/* NAND support */
+#ifdef CONFIG_NAND
+/* NAND: device related configs */
+#define CONFIG_SYS_NAND_PAGE_SIZE 4096
+#define CONFIG_SYS_NAND_OOBSIZE 224
+#define CONFIG_SYS_NAND_BLOCK_SIZE (256*1024)
+#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
+ CONFIG_SYS_NAND_PAGE_SIZE)
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+/* NAND: driver related configs */
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_NAND_OMAP_ELM
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH16_CODE_HW
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
+ 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, \
+ 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, \
+ 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, \
+ 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, \
+ 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, \
+ 60, 61, 62, 63, 64, 65, 66, 67, 68, 69, \
+ 70, 71, 72, 73, 74, 75, 76, 77, 78, 79, \
+ 80, 81, 82, 83, 84, 85, 86, 87, 88, 89, \
+ 90, 91, 92, 93, 94, 95, 96, 97, 98, 99, \
+ 100, 101, 102, 103, 104, 105, 106, 107, 108, 109, \
+ 110, 111, 112, 113, 114, 115, 116, 117, 118, 119, \
+ 120, 121, 122, 123, 124, 125, 126, 127, 128, 129, \
+ 130, 131, 132, 133, 134, 135, 136, 137, 138, 139, \
+ 140, 141, 142, 143, 144, 145, 146, 147, 148, 149, \
+ 150, 151, 152, 153, 154, 155, 156, 157, 158, 159, \
+ 160, 161, 162, 163, 164, 165, 166, 167, 168, 169, \
+ 170, 171, 172, 173, 174, 175, 176, 177, 178, 179, \
+ 180, 181, 182, 183, 184, 185, 186, 187, 188, 189, \
+ 190, 191, 192, 193, 194, 195, 196, 197, 198, 199, \
+ 200, 201, 202, 203, 204, 205, 206, 207, 208, 209, \
+ }
+#define CONFIG_SYS_NAND_ECCSIZE 512
+#define CONFIG_SYS_NAND_ECCBYTES 26
+#define MTDIDS_DEFAULT "nand0=nand.0"
+#define MTDPARTS_DEFAULT "mtdparts=nand.0:" \
+ "256k(NAND.SPL)," \
+ "256k(NAND.SPL.backup1)," \
+ "256k(NAND.SPL.backup2)," \
+ "256k(NAND.SPL.backup3)," \
+ "512k(NAND.u-boot-spl-os)," \
+ "1m(NAND.u-boot)," \
+ "256k(NAND.u-boot-env)," \
+ "256k(NAND.u-boot-env.backup1)," \
+ "7m(NAND.kernel)," \
+ "-(NAND.rootfs)"
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x00180000
+/* NAND: SPL related configs */
+#ifdef CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_AM33XX_BCH
+#endif
+/* NAND: SPL falcon mode configs */
+#ifdef CONFIG_SPL_OS_BOOT
+#define CONFIG_CMD_SPL_NAND_OFS 0x00100000 /* os parameters */
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x00300000 /* kernel offset */
+#define CONFIG_CMD_SPL_WRITE_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#endif
+#endif /* !CONFIG_NAND */
+
#endif /* __CONFIG_AM43XX_EVM_H */
OpenPOWER on IntegriCloud