ppc4xx: remove PMC405 board

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>

1 files changed, 0 insertions, 318 deletions

diff --git a/include/configs/PMC405.h b/include/configs/PMC405.h
deleted file mode 100644
index c68d9a6ec6..0000000000
--- a/include/configs/PMC405.h
+++ /dev/null
@@ -1,318 +0,0 @@
-/*
- * (C) Copyright 2001-2004
- * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-
-#define CONFIG_405GP		1	/* This is a PPC405 CPU		*/
-#define CONFIG_PMC405		1	/* ...on a PMC405 board		*/
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFF80000
-
-#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
-#define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
-
-#define CONFIG_SYS_CLK_FREQ	33330000 /* external frequency to pll	*/
-
-#define CONFIG_BAUDRATE		9600
-#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
-
-/* Only interrupt boot if space is pressed. */
-#define CONFIG_AUTOBOOT_KEYED 1
-#define CONFIG_AUTOBOOT_PROMPT	\
-	"Press SPACE to abort autoboot in %d seconds\n", bootdelay
-#undef CONFIG_AUTOBOOT_DELAY_STR
-#define CONFIG_AUTOBOOT_STOP_STR " "
-
-#undef CONFIG_BOOTARGS
-#undef CONFIG_BOOTCOMMAND
-
-#define CONFIG_PREBOOT			/* enable preboot variable	*/
-
-#define CFG_BOOTM_LEN		0x1000000 /* support booting of huge images */
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1	/* allow baudrate change	*/
-
-#undef  CONFIG_HAS_ETH1
-
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_PHY_ADDR		0	/* PHY address			*/
-#define CONFIG_LXT971_NO_SLEEP	1	/* disable sleep mode in LXT971	*/
-#define CONFIG_RESET_PHY_R	1	/* use reset_phy()		*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_BSP
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_UNIVERSE
-#define CONFIG_CMD_EEPROM
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define CONFIG_RTC_MC146818		/* DS1685 is MC146818 compatible */
-#define CONFIG_SYS_RTC_REG_BASE_ADDR	0xF0000500 /* RTC Base Address */
-
-#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory */
-
-#undef CONFIG_SYS_HUSH_PARSER			/* use "hush" command parser */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE	512		/* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE /* Boot Argument Buffer Sz */
-
-#define CONFIG_SYS_DEVICE_NULLDEV	1	/* include nulldev device */
-
-#define CONFIG_SYS_CONSOLE_INFO_QUIET	1	/* don't print console info */
-
-#define CONFIG_AUTO_COMPLETE		1       /* add autocompletion support */
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
-
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK		/* no external serial clock */
-#define CONFIG_SYS_BASE_BAUD	806400
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE	\
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address */
-#define CONFIG_SYS_EXTBDINFO	1	/* To use extended board_into (bd_t) */
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history */
-#define CONFIG_LOOPW		1	/* enable loopw command */
-
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-
-#define CONFIG_SYS_RX_ETH_BUFFER	16
-
-/*
- * PCI stuff
- */
-#define PCI_HOST_ADAPTER	0	/* configure as pci adapter	*/
-#define PCI_HOST_FORCE		1	/* configure as pci host	*/
-#define PCI_HOST_AUTO		2	/* detected via arbiter enable	*/
-
-#define CONFIG_PCI			/* include pci support		*/
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_PCI_HOST	PCI_HOST_AUTO   /* select pci host function	*/
-#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
-					/* resource configuration	*/
-
-#define CONFIG_PCI_SCAN_SHOW		/* print pci devices @ startup	*/
-
-#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1	/* don't skip host bridge config */
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID_NONMONARCH 0x0408 /* PCI Device ID */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID_MONARCH 0x0409 /* PCI Device ID */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID pmc405_pci_subsys_deviceid()
-
-#define CONFIG_SYS_PCI_CLASSCODE       0x0b20 /* Processor/PPC */
-
-#define CONFIG_SYS_PCI_PTM1LA  (bd->bi_memstart) /* point to sdram	*/
-#define CONFIG_SYS_PCI_PTM1MS  (~(bd->bi_memsize - 1) | 1) /* memsize, enable */
-#define CONFIG_SYS_PCI_PTM1PCI 0x00000000	/* Host: use this pci address */
-#define CONFIG_SYS_PCI_PTM2LA  0xef000000	/* point to internal regs */
-#define CONFIG_SYS_PCI_PTM2MS  0xff000001	/* 16MB, enable */
-#define CONFIG_SYS_PCI_PTM2PCI 0x00000000	/* Host: use this pci address */
-
-#define CONFIG_PCI_4xx_PTM_OVERWRITE	1 /* overwrite PTMx settings by env */
-
-/*
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN		(~(CONFIG_SYS_TEXT_BASE) + 1)
-#define CONFIG_SYS_MALLOC_LEN		(128 * 1024) /* 128 kB for malloc() */
-
-#define CONFIG_PRAM			0 /* use pram variable to overwrite */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ	(8 << 20) /* Initial Memory map for Linux */
-
-/*
- * FLASH organization
- */
-#define CONFIG_SYS_FLASH_BASE		0xFE000000
-#define CONFIG_SYS_FLASH_INCREMENT	0x01000000
-
-#define CONFIG_SYS_FLASH_CFI		1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER		1 /* Use the common driver */
-#define CONFIG_SYS_FLASH_PROTECTION	1 /* don't use hardware protection */
-#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST {{0xfff80000, 0x80000}}
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (faster) */
-#define CONFIG_SYS_MAX_FLASH_BANKS	2 /* max num of flash banks */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE, \
-			CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_INCREMENT}
-#define CONFIG_SYS_MAX_FLASH_SECT	128 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_EMPTY_INFO	/* print 'E' for empty sector on fli */
-
-/*
- * Environment Variable setup
- */
-#define CONFIG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
-
-/* environment starts at the beginning of the EEPROM */
-#define CONFIG_ENV_OFFSET	0x000
-#define CONFIG_ENV_SIZE		0x800 /* 2048 bytes may be used for env vars */
-
-#define CONFIG_SYS_NVRAM_BASE_ADDR	0xF0000500	/* NVRAM base address */
-#define CONFIG_SYS_NVRAM_SIZE		242		/* NVRAM size */
-
-/*
- * I2C EEPROM (CAT24WC16) for environment
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT24W16 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24W16 has */
-					/* 16 byte page write mode using*/
-					/* last	4 bits of the address */
-
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-
-/*
- * External Bus Controller (EBC) Setup
- */
-#define FLASH0_BA	0xFF000000	/* FLASH 0 Base Address	*/
-#define FLASH1_BA	0xFE000000	/* FLASH 1 Base Address	*/
-#define CAN_BA		0xF0000000	/* CAN Base Addres	*/
-#define RTC_BA		0xF0000500	/* RTC Base Address	*/
-#define NVRAM_BA	0xF0200000	/* NVRAM Base Address	*/
-
-/* Memory Bank 0 (Flash Bank 0) initialization */
-#define CONFIG_SYS_EBC_PB0AP	0x92015480
-/* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit */
-#define CONFIG_SYS_EBC_PB0CR	(FLASH0_BA | 0x9A000)
-
-/* Memory Bank 1 (Flash Bank 1) initialization */
-#define CONFIG_SYS_EBC_PB1AP	0x92015480
-/* BAS=0xFE0,BS=16MB,BU=R/W,BW=16bit*/
-#define CONFIG_SYS_EBC_PB1CR	(FLASH1_BA | 0x9A000)
-
-/* Memory Bank 2 (CAN0, 1, RTC) initialization */
-/* TWT=5,TH=2,CSN=0,OEN=0,WBN=0,WBF=0      */
-#define CONFIG_SYS_EBC_PB2AP	0x03000440
-/* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-#define CONFIG_SYS_EBC_PB2CR	(CAN_BA | 0x18000)
-
-/* Memory Bank 3 -> unused */
-
-/* Memory Bank 4 (NVRAM) initialization */
-/* TWT=5,TH=2,CSN=0,OEN=0,WBN=0,WBF=0 */
-#define CONFIG_SYS_EBC_PB4AP	0x03000440
-/* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-#define CONFIG_SYS_EBC_PB4CR	(NVRAM_BA | 0x18000)
-
-/*
- * FPGA stuff
- */
-/* FPGA program pin configuration */
-#define CONFIG_SYS_FPGA_PRG		0x04000000 /* JTAG TMS pin (output) */
-#define CONFIG_SYS_FPGA_CLK		0x02000000 /* JTAG TCK pin (output) */
-#define CONFIG_SYS_FPGA_DATA		0x01000000 /* JTAG TDO pin (output) */
-#define CONFIG_SYS_FPGA_INIT		0x00010000 /* unused (ppc input) */
-#define CONFIG_SYS_FPGA_DONE		0x00008000 /* JTAG TDI pin (input) */
-
-/* pass Ethernet MAC to VxWorks */
-#define CONFIG_SYS_VXWORKS_MAC_PTR	0x00000000
-
-/*
- * GPIOs
- */
-#define CONFIG_SYS_VPEN			(0x80000000 >>  3) /* GPIO3 */
-#define CONFIG_SYS_NONMONARCH		(0x80000000 >> 14) /* GPIO14 */
-#define CONFIG_SYS_XEREADY		(0x80000000 >> 15) /* GPIO15 */
-#define CONFIG_SYS_INTA_FAKE		(0x80000000 >> 19) /* GPIO19 */
-#define CONFIG_SYS_SELF_RST		(0x80000000 >> 21) /* GPIO21 */
-#define CONFIG_SYS_REV1_2		(0x80000000 >> 23) /* GPIO23 */
-
-/*
- * Definitions for initial stack pointer and data area (in data cache)
- */
-
-/* use on chip memory (OCM) for temperary stack until sdram is tested */
-#define CONFIG_SYS_TEMP_STACK_OCM	1
-
-/* On Chip Memory location */
-#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
-#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
-
-/* inside of SDRAM */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR
-
-/* End of used area in RAM */
-#define CONFIG_SYS_INIT_RAM_SIZE		CONFIG_SYS_OCM_DATA_SIZE
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-					 GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-
-#endif /* __CONFIG_H */