mpc8xx: remove v37 board support

This board is old enough and has no maintainer.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

2 files changed, 0 insertions, 398 deletions

diff --git a/include/commproc.h b/include/commproc.h
index 48b761fd82..52ac4caf5a 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -1023,29 +1023,6 @@ typedef struct scc_enet {
 # endif	/* CONFIG_FEC_ENET */
 #endif	/* CONFIG_TQM855L/M, TQM860L/M, TQM862L/M */
 
-/***  V37  **********************************************************/
-
-#ifdef CONFIG_V37
-/* This ENET stuff is for the MPC823 with ethernet on SCC2.  Some of
- * this may be unique to the Marel V37 configuration.
- * Note TENA is on Port B.
- */
-#define	PROFF_ENET	PROFF_SCC2
-#define	CPM_CR_ENET	CPM_CR_CH_SCC2
-#define	SCC_ENET	1
-#define PA_ENET_RXD	((ushort)0x0004)
-#define PA_ENET_TXD	((ushort)0x0008)
-#define PA_ENET_TCLK	((ushort)0x0400)
-#define PA_ENET_RCLK	((ushort)0x0200)
-#define PB_ENET_TENA	((uint)0x00002000)
-#define PC_ENET_CLSN	((ushort)0x0040)
-#define PC_ENET_RENA	((ushort)0x0080)
-
-#define SICR_ENET_MASK	((uint)0x0000ff00)
-#define SICR_ENET_CLKRT	((uint)0x00002e00)
-#endif	/* CONFIG_V37 */
-
-
 /*********************************************************************/
 
 /* SCC Event register as used by Ethernet.
diff --git a/include/configs/v37.h b/include/configs/v37.h
deleted file mode 100644
index 0d01fe207e..0000000000
--- a/include/configs/v37.h
+++ /dev/null
@@ -1,375 +0,0 @@
-/*
- * (C) Copyright 2000, 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC823		1	/* This is a MPC823 CPU		*/
-#define CONFIG_V37		1	/* ...on a Marel V37 board	*/
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-#define CONFIG_LCD
-#define CONFIG_MPC8XX_LCD
-#define CONFIG_SHARP_LQ084V1DG21
-#undef CONFIG_LCD_LOGO
-
-/*-----------------------------------------------------------------------------
- * I2C Configuration
- *-----------------------------------------------------------------------------
- */
-#define CONFIG_I2C              1
-#define CONFIG_SYS_I2C_SLAVE           0x2
-
-#define	CONFIG_8xx_CONS_SMC1	1
-#undef	CONFIG_8xx_CONS_SMC2		/* Console is on SMC2		*/
-#undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		9600	/* console baudrate = 115kbps	*/
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	2	/* autoboot after 2 seconds	*/
-#endif
-
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-#define CONFIG_PREBOOT	"echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define CONFIG_BOOTCOMMAND							\
-	"tftpboot; "								\
-	"setenv bootargs console=tty0 "                                   \
-	"root=/dev/nfs rw nfsroot=${serverip}:${rootpath} "			\
-	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; "	\
-	"bootm"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define	CONFIG_CAN_DRIVER	1	/* CAN Driver support enabled	*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_DATE
-
-
-/*
- * JFFS2 partitions
- *
- */
-/* No command line, one static partition, whole device */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV		"nor1"
-#define CONFIG_JFFS2_PART_SIZE		0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET	0x00000000
-
-/* mtdparts command line support */
-/* Note: fake mtd_id used, no linux mtd map file */
-/*
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT		"nor1=v37-1"
-#define MTDPARTS_DEFAULT	"mtdparts=v37-1:-(jffs2)"
-*/
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xF0000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE0		0x40000000
-#define CONFIG_SYS_FLASH_BASE1		0x60000000
-#define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_FLASH_BASE1
-
-#if defined(DEBUG)
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#else
-#define	CONFIG_SYS_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor	*/
-#endif
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE0
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	35	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define	CONFIG_ENV_IS_IN_NVRAM	1
-#define	CONFIG_ENV_ADDR		0x80000000/* Address of Environment */
-#define	CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
-
-#define CONFIG_ENV_OFFSET		0
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	0xFFFFFF88
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_FRC | SIUMCR_GB5E)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-/*%%%#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-/*
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-*/
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
- */
-/* up to 50 MHz we use a 1:1 clock */
-#define CONFIG_SYS_PLPRCR	( (1524 << PLPRCR_MF_SHIFT) | PLPRCR_SPLSS | PLPRCR_TMIST | PLPRCR_TEXPS )
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-/* up to 50 MHz we use a 1:1 clock */
-#define CONFIG_SYS_SCCR	(SCCR_COM00 | SCCR_TBS)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#undef	CONFIG_IDE_PCCARD		/* Use IDE with PC Card	Adapter	*/
-
-#undef	CONFIG_IDE_PCMCIA		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER	0
-
-/*
- * Init Memory Controller:
- *
- * BR0 and OR0 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #1	*/
-
-#define CONFIG_SYS_PRELIM_OR_AM	0xFE000000	/* OR addr mask */
-
-#define CONFIG_SYS_OR_TIMING_FLASH	0xF56
-
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V)
-
-#define CONFIG_SYS_OR5_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR5_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_32 | BR_V)
-
-/*
- * BR1 and OR1 (Battery backed SRAM)
- */
-#define	CONFIG_SYS_BR1_PRELIM	0x80000401
-#define CONFIG_SYS_OR1_PRELIM	0xFFC00736
-
-/*
- * BR2 and OR2 (SDRAM)
- */
-#define SDRAM_BASE_PRELIM	0x00000000	/* SDRAM base	*/
-#define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB */
-
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-/* Marel V37 mem setting */
-
-#define	CONFIG_SYS_BR3_CAN	0xC0000401
-#define CONFIG_SYS_OR3_CAN	0xFFFF0724
-
-/*
-#define	CONFIG_SYS_BR3_PRELIM	0xFA400001
-#define CONFIG_SYS_OR3_PRELIM	0xFFFF8910
-#define	CONFIG_SYS_BR4_PRELIM	0xFA000401
-#define CONFIG_SYS_OR4_PRELIM	0xFFFE0970
-*/
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MAMR_PTA	97		/* start with divider for 100 MHz	*/
-
-/*
- * Refresh clock Prescalar
- */
-#define CONFIG_SYS_MPTPR	MPTPR_PTP_DIV16
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 10 column SDRAM */
-#define CONFIG_SYS_MAMR_10COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A12 |	\
-			 MAMR_GPL_A4DIS | MAMR_RLFA_4X | MAMR_WLFA_3X | MAMR_TLFA_16X)
-
-#endif	/* __CONFIG_H */