ppc4xx: remove DP405 board

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>

1 files changed, 0 insertions, 246 deletions

diff --git a/include/configs/DP405.h b/include/configs/DP405.h
deleted file mode 100644
index 68e4a7f405..0000000000
--- a/include/configs/DP405.h
+++ /dev/null
@@ -1,246 +0,0 @@
-/*
- * (C) Copyright 2001-2003
- * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405EP		1	/* This is a PPC405 CPU		*/
-#define CONFIG_DP405		1	/* ...on a DP405 board		*/
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFFD0000
-
-#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
-#define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
-
-#define CONFIG_SYS_CLK_FREQ	33333300 /* external frequency to pll	*/
-
-#define CONFIG_BAUDRATE		9600
-#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
-
-#undef	CONFIG_BOOTARGS
-#undef  CONFIG_BOOTCOMMAND
-
-#define CONFIG_PREBOOT                  /* enable preboot variable      */
-
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_BSP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_EEPROM
-
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_NFS
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
-
-#define CONFIG_PRAM		2	/* reserve 2 kB "protected RAM" */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#undef	CONFIG_SYS_HUSH_PARSER			/* use "hush" command parser	*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_DEVICE_NULLDEV	1	/* include nulldev device	*/
-
-#define CONFIG_SYS_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
-
-#undef	CONFIG_SYS_EXT_SERIAL_CLOCK	       /* no external serial clock used */
-#define CONFIG_SYS_BASE_BAUD	    691200
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE	\
-	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
-	 57600, 115200, 230400, 460800, 921600 }
-
-#define CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address */
-#define CONFIG_SYS_EXTBDINFO	1		/* To use extended board_into (bd_t) */
-
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define FLASH_BASE0_PRELIM	0xFFC00000	/* FLASH bank #0	*/
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms)	*/
-
-#define CONFIG_SYS_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
-#define CONFIG_SYS_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
-#define CONFIG_SYS_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
-/*
- * The following defines are added for buggy IOP480 byte interface.
- * All other boards should use the standard values (CPCI405 etc.)
- */
-#define CONFIG_SYS_FLASH_READ0		0x0000	/* 0 is standard			*/
-#define CONFIG_SYS_FLASH_READ1		0x0001	/* 1 is standard			*/
-#define CONFIG_SYS_FLASH_READ2		0x0002	/* 2 is standard			*/
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_MONITOR_BASE
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN		(~(CONFIG_SYS_TEXT_BASE) + 1)
-#define CONFIG_SYS_MALLOC_LEN		(256 * 1024)
-
-#if (CONFIG_SYS_MONITOR_BASE < FLASH_BASE0_PRELIM)
-# define CONFIG_SYS_RAMBOOT		1
-#else
-# undef CONFIG_SYS_RAMBOOT
-#endif
-
-/*-----------------------------------------------------------------------
- * Environment Variable setup
- */
-#define CONFIG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
-#define CONFIG_ENV_OFFSET		0x100	/* environment starts at the beginning of the EEPROM */
-#define CONFIG_ENV_SIZE		0x700	/* 2048 bytes may be used for env vars*/
-				   /* total size of a CAT24WC16 is 2048 bytes */
-
-/*-----------------------------------------------------------------------
- * I2C EEPROM (CAT24WC16) for environment
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"	*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
-					/* 16 byte page write mode using*/
-					/* last 4 bits of the address	*/
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
-
-/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
- */
-
-#define CAN_BA		0xF0000000	    /* CAN Base Address			*/
-
-/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization			*/
-#define CONFIG_SYS_EBC_PB0AP		0x92015480
-#define CONFIG_SYS_EBC_PB0CR		0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization		*/
-#define CONFIG_SYS_EBC_PB2AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CONFIG_SYS_EBC_PB2CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
-
-/*-----------------------------------------------------------------------
- * FPGA stuff
- */
-/* FPGA program pin configuration */
-#define CONFIG_SYS_FPGA_PRG		0x04000000  /* JTAG TMS pin (ppc output)     */
-#define CONFIG_SYS_FPGA_CLK		0x02000000  /* JTAG TCK pin (ppc output)     */
-#define CONFIG_SYS_FPGA_DATA		0x01000000  /* JTAG TDO->TDI data pin (ppc output) */
-#define CONFIG_SYS_FPGA_INIT		0x00010000  /* unused (ppc input)	     */
-#define CONFIG_SYS_FPGA_DONE		0x00008000  /* JTAG TDI->TDO pin (ppc input) */
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in data cache)
- */
-/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CONFIG_SYS_TEMP_STACK_OCM	  1
-
-/* On Chip Memory location */
-#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
-#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM		*/
-#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM	*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Definitions for GPIO setup (PPC405EP specific)
- *
- * GPIO0[0]	- External Bus Controller BLAST output
- * GPIO0[1-9]	- Instruction trace outputs -> GPIO
- * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
- * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
- * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
- * GPIO0[24-27] - UART0 control signal inputs/outputs
- * GPIO0[28-29] - UART1 data signal input/output
- * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
- */
-/* GPIO Input:		OSR=00, ISR=00, TSR=00, TCR=0 */
-/* GPIO Output:		OSR=00, ISR=00, TSR=00, TCR=1 */
-/* Alt. Funtion Input:	OSR=00, ISR=01, TSR=00, TCR=0 */
-/* Alt. Funtion Output: OSR=01, ISR=00, TSR=00, TCR=1 */
-#define CONFIG_SYS_GPIO0_OSRL		0x40000540  /*	0 ... 15 */
-#define CONFIG_SYS_GPIO0_OSRH		0x00000110  /* 16 ... 31 */
-#define CONFIG_SYS_GPIO0_ISR1L		0x00000000  /*	0 ... 15 */
-#define CONFIG_SYS_GPIO0_ISR1H		0x14000045  /* 16 ... 31 */
-#define CONFIG_SYS_GPIO0_TSRL		0x00000000  /*	0 ... 15 */
-#define CONFIG_SYS_GPIO0_TSRH		0x00000000  /* 16 ... 31 */
-#define CONFIG_SYS_GPIO0_TCR		0xB7FE0014  /*	0 ... 31 */
-
-/*
- * Default speed selection (cpu_plb_opb_ebc) in mhz.
- * This value will be set if iic boot eprom is disabled.
- */
-#define PLLMR0_DEFAULT	 PLLMR0_133_66_66_33
-#define PLLMR1_DEFAULT	 PLLMR1_133_66_66_33
-
-#endif	/* __CONFIG_H */