mpc8260: remove ep82xxm board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

1 files changed, 0 insertions, 383 deletions

diff --git a/include/configs/ep82xxm.h b/include/configs/ep82xxm.h
deleted file mode 100644
index cf31f0f141..0000000000
--- a/include/configs/ep82xxm.h
+++ /dev/null
@@ -1,383 +0,0 @@
-/*
- * Copyright (C) 2006 Embedded Planet, LLC.
- *
- * U-Boot configuration for Embedded Planet EP82xxM boards.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CPU_ID_STR		"MPC8270"
-
-#define CONFIG_EP82XXM	/* Embedded Planet EP82xxM H 1.0 board */
-			/* 256MB SDRAM / 64MB FLASH */
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFF00000
-
-#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f */
-
-/* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */
-#define CONFIG_ENV_OVERWRITE
-
-/*
- * Select serial console configuration
- *
- * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- */
-#define	CONFIG_CONS_ON_SMC		/* Console is on SMC         */
-#undef  CONFIG_CONS_ON_SCC		/* It's not on SCC           */
-#undef	CONFIG_CONS_NONE		/* It's not on external UART */
-#define CONFIG_CONS_INDEX	1	/* SMC1 is used for console  */
-
-#define CONFIG_SYS_BCSR		0xFA000000
-
-/*
- * Select ethernet configuration
- *
- * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected,
- * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for
- * SCC, 1-3 for FCC)
- *
- * If CONFIG_ETHER_NONE is defined, then either the ethernet routines
- * must be defined elsewhere (as for the console), or CONFIG_CMD_NET
- * must be unset.
- */
-#undef	CONFIG_ETHER_ON_SCC		/* Ethernet is not on SCC */
-#define CONFIG_ETHER_ON_FCC		/* Ethernet is on FCC     */
-#undef	CONFIG_ETHER_NONE		/* No external Ethernet   */
-
-
-#define CONFIG_ETHER_ON_FCC2
-#define CONFIG_ETHER_ON_FCC3
-
-#define CONFIG_SYS_CMXFCR_MASK3	(CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK)
-#define CONFIG_SYS_CMXFCR_VALUE3	(CMXFCR_RF3CS_CLK15 | CMXFCR_TF3CS_CLK16)
-#define CONFIG_SYS_CMXFCR_MASK2	(CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
-#define CONFIG_SYS_CMXFCR_VALUE2	(CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
-
-#define CONFIG_SYS_CPMFCR_RAMTYPE	0
-#define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE | FCC_PSMR_LPB)
-
-#define CONFIG_MII			/* MII PHY management        */
-#define CONFIG_BITBANGMII		/* Bit-banged MDIO interface */
-
-/*
- * GPIO pins used for bit-banged MII communications
- */
-#define MDIO_PORT		0	/* Not used - implemented in BCSR */
-
-#define MDIO_ACTIVE		(*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFB)
-#define MDIO_TRISTATE		(*(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x04)
-#define MDIO_READ		(*(vu_char *)(CONFIG_SYS_BCSR + 8) & 1)
-
-#define MDIO(bit)		if(bit) *(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x01; \
-				else	*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFE
-
-#define MDC(bit)		if(bit) *(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x02; \
-				else	*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFD
-
-#define MIIDELAY		udelay(1)
-
-
-#ifndef CONFIG_8260_CLKIN
-#define CONFIG_8260_CLKIN	66000000 /* in Hz */
-#endif
-
-#define CONFIG_BAUDRATE		115200
-
-#define CONFIG_SYS_VXWORKS_MAC_PTR 0x4300 /* Pass Ethernet MAC to VxWorks */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_DIAG
-
-
-#define CONFIG_ETHADDR		00:10:EC:00:88:65
-#define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR		00:10:EC:80:88:65
-#define CONFIG_IPADDR		10.0.0.245
-#define CONFIG_HOSTNAME		EP82xxM
-#define CONFIG_SERVERIP		10.0.0.26
-#define CONFIG_GATEWAYIP	10.0.0.1
-#define CONFIG_NETMASK		255.255.255.0
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
-#define CONFIG_ENV_IN_OWN_SECT	1
-#define CONFIG_AUTO_COMPLETE	1
-#define	CONFIG_EXTRA_ENV_SETTINGS	"ethprime=FCC3"
-
-#if defined(CONFIG_CMD_KGDB)
-#undef	CONFIG_KGDB_ON_SMC		/* define if kgdb on SMC */
-#define CONFIG_KGDB_ON_SCC		/* define if kgdb on SCC */
-#undef	CONFIG_KGDB_NONE		/* define if kgdb on something else */
-#define CONFIG_KGDB_INDEX	1	/* which serial channel for kgdb */
-#define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port at */
-#endif
-
-#define CONFIG_BZIP2	/* include support for bzip2 compressed images */
-#undef	CONFIG_WATCHDOG			/* disable platform specific watchdog */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
-#define CONFIG_SYS_PROMPT		"ep82xxm=> "	/* Monitor Command Prompt   */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
-#else
-#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size  */
-#define CONFIG_SYS_MAXARGS		16		/* max number of command args */
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size  */
-
-#define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/*-----------------------------------------------------------------------
- * Environment
- *----------------------------------------------------------------------*/
-/*
- * Define here the location of the environment variables (FLASH or EEPROM).
- * Note: DENX encourages to use redundant environment in FLASH.
- */
-#if 1
-#define CONFIG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
-#else
-#define CONFIG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * FLASH related
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH_BASE		0xFC000000
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of flash banks	*/
-#define CONFIG_SYS_MAX_FLASH_SECT	512	/* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector in flinfo */
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SECT_SIZE	0x20000
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#endif /* CONFIG_ENV_IS_IN_FLASH */
-
-/*-----------------------------------------------------------------------
- * I2C
- *----------------------------------------------------------------------*/
-/* EEPROM Configuration */
-#define CONFIG_SYS_EEPROM_SIZE	0x1000
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x54
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10
-
-#ifdef CONFIG_ENV_IS_IN_EEPROM
-#define CONFIG_ENV_SIZE		0x200	    /* Size of Environment vars */
-#define CONFIG_ENV_OFFSET		0x0
-#endif /* CONFIG_ENV_IS_IN_EEPROM */
-
-/* RTC Configuration */
-#define CONFIG_RTC_M41T11	1	/* uses a M41T81 */
-#define CONFIG_SYS_I2C_RTC_ADDR	0x68
-#define CONFIG_M41T11_BASE_YEAR	1900
-
-/* I2C SYSMON (LM75) */
-#define CONFIG_DTT_LM75		1
-#define CONFIG_DTT_SENSORS	{0}
-#define CONFIG_SYS_DTT_MAX_TEMP	70
-#define CONFIG_SYS_DTT_LOW_TEMP	-30
-#define	CONFIG_SYS_DTT_HYSTERESIS	3
-
-/*-----------------------------------------------------------------------
- * NVRAM Configuration
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_NVRAM_BASE_ADDR	0xFA080000
-#define CONFIG_SYS_NVRAM_SIZE		(128*1024)-16
-
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-/* General PCI */
-#define CONFIG_PCI			/* include pci support	        */
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play   */
-#define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup  */
-#define CONFIG_PCI_BOOTDELAY	0
-
-/* PCI Memory map (if different from default map */
-#define CONFIG_SYS_PCI_SLV_MEM_LOCAL	CONFIG_SYS_SDRAM_BASE		/* Local base */
-#define CONFIG_SYS_PCI_SLV_MEM_BUS		0x00000000	/* PCI base */
-#define CONFIG_SYS_PICMR0_MASK_ATTRIB	(PICMR_MASK_512MB | PICMR_ENABLE | \
-				 PICMR_PREFETCH_EN)
-
-/*
- * These are the windows that allow the CPU to access PCI address space.
- * All three PCI master windows, which allow the CPU to access PCI
- * prefetch, non prefetch, and IO space (see below), must all fit within
- * these windows.
- */
-
-/*
- * Master window that allows the CPU to access PCI Memory (prefetch).
- * This window will be setup with the second set of Outbound ATU registers
- * in the bridge.
- */
-
-#define CONFIG_SYS_PCI_MSTR_MEM_LOCAL	0x80000000          /* Local base */
-#define CONFIG_SYS_PCI_MSTR_MEM_BUS	0x80000000          /* PCI base   */
-#define	CONFIG_SYS_CPU_PCI_MEM_START	PCI_MSTR_MEM_LOCAL
-#define CONFIG_SYS_PCI_MSTR_MEM_SIZE	0x20000000          /* 512MB */
-#define CONFIG_SYS_POCMR0_MASK_ATTRIB	(POCMR_MASK_512MB | POCMR_ENABLE | POCMR_PREFETCH_EN)
-
-/*
- * Master window that allows the CPU to access PCI Memory (non-prefetch).
- * This window will be setup with the second set of Outbound ATU registers
- * in the bridge.
- */
-
-#define CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL    0xA0000000          /* Local base */
-#define CONFIG_SYS_PCI_MSTR_MEMIO_BUS      0xA0000000          /* PCI base   */
-#define CONFIG_SYS_CPU_PCI_MEMIO_START     PCI_MSTR_MEMIO_LOCAL
-#define CONFIG_SYS_PCI_MSTR_MEMIO_SIZE     0x20000000          /* 512MB */
-#define CONFIG_SYS_POCMR1_MASK_ATTRIB      (POCMR_MASK_512MB | POCMR_ENABLE)
-
-/*
- * Master window that allows the CPU to access PCI IO space.
- * This window will be setup with the first set of Outbound ATU registers
- * in the bridge.
- */
-
-#define CONFIG_SYS_PCI_MSTR_IO_LOCAL       0xF6000000          /* Local base */
-#define CONFIG_SYS_PCI_MSTR_IO_BUS         0x00000000          /* PCI base   */
-#define CONFIG_SYS_CPU_PCI_IO_START        PCI_MSTR_IO_LOCAL
-#define CONFIG_SYS_PCI_MSTR_IO_SIZE        0x02000000          /* 64MB */
-#define CONFIG_SYS_POCMR2_MASK_ATTRIB      (POCMR_MASK_32MB | POCMR_ENABLE | POCMR_PCI_IO)
-
-
-/* PCIBR0 - for PCI IO*/
-#define CONFIG_SYS_PCI_MSTR0_LOCAL		CONFIG_SYS_PCI_MSTR_IO_LOCAL		/* Local base */
-#define CONFIG_SYS_PCIMSK0_MASK		~(CONFIG_SYS_PCI_MSTR_IO_SIZE - 1U)	/* Size of window */
-/* PCIBR1 - prefetch and non-prefetch regions joined together */
-#define CONFIG_SYS_PCI_MSTR1_LOCAL		CONFIG_SYS_PCI_MSTR_MEM_LOCAL
-#define CONFIG_SYS_PCIMSK1_MASK		~(CONFIG_SYS_PCI_MSTR_MEM_SIZE + CONFIG_SYS_PCI_MSTR_MEMIO_SIZE - 1U)
-
-
-#define	CONFIG_SYS_DIRECT_FLASH_TFTP
-
-#if defined(CONFIG_CMD_JFFS2)
-#define CONFIG_SYS_JFFS2_FIRST_BANK	0
-#define CONFIG_SYS_JFFS2_NUM_BANKS	CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_FIRST_SECTOR  0
-#define CONFIG_SYS_JFFS2_LAST_SECTOR   62
-#define CONFIG_SYS_JFFS2_SORT_FRAGMENTS
-#define CONFIG_SYS_JFFS_CUSTOM_PART
-#endif
-
-#if defined(CONFIG_CMD_I2C)
-#define CONFIG_HARD_I2C		1	/* To enable I2C support	*/
-#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed			*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F	/* I2C slave address		*/
-#endif
-
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN		(512 << 10)	/* Reserve 256KB for Monitor */
-
-#define CONFIG_SYS_DEFAULT_IMMR	0x00010000
-#define CONFIG_SYS_IMMR		0xF0000000
-
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE	0x2000	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-
-/* Hard reset configuration word */
-#define CONFIG_SYS_HRCW_MASTER		0 /*0x1C800641*/  /* Not used - provided by CPLD */
-/* No slaves */
-#define CONFIG_SYS_HRCW_SLAVE1		0
-#define CONFIG_SYS_HRCW_SLAVE2		0
-#define CONFIG_SYS_HRCW_SLAVE3		0
-#define CONFIG_SYS_HRCW_SLAVE4		0
-#define CONFIG_SYS_HRCW_SLAVE5		0
-#define CONFIG_SYS_HRCW_SLAVE6		0
-#define CONFIG_SYS_HRCW_SLAVE7		0
-
-#define CONFIG_SYS_MALLOC_LEN		(4096 << 10)	/* Reserve 4 MB for malloc()	*/
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC8260 CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
-
-#define CONFIG_SYS_HID0_INIT		0
-#define CONFIG_SYS_HID0_FINAL		0
-
-#define CONFIG_SYS_HID2		0
-
-#define CONFIG_SYS_SIUMCR		0x02610000
-#define CONFIG_SYS_SYPCR		0xFFFF0689
-#define CONFIG_SYS_BCR			0x8080E000
-#define CONFIG_SYS_SCCR		0x00000001
-
-#define CONFIG_SYS_RMR			0
-#define CONFIG_SYS_TMCNTSC		0x000000C3
-#define CONFIG_SYS_PISCR		0x00000083
-#define CONFIG_SYS_RCCR		0
-
-#define CONFIG_SYS_MPTPR		0x0A00
-#define CONFIG_SYS_PSDMR		0xC432246E
-#define CONFIG_SYS_PSRT		0x32
-
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_SDRAM_BR		(CONFIG_SYS_SDRAM_BASE | 0x00000041)
-#define CONFIG_SYS_SDRAM_OR		0xF0002900
-
-#define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE | 0x00001801)
-#define CONFIG_SYS_OR0_PRELIM		0xFC000882
-#define CONFIG_SYS_BR4_PRELIM		(CONFIG_SYS_BCSR | 0x00001001)
-#define CONFIG_SYS_OR4_PRELIM		0xFFF00050
-
-#define CONFIG_SYS_RESET_ADDRESS	0xFFF00100
-
-#endif /* __CONFIG_H */