* Patches by David Müller, 12 Jun 2003:

  - rewrite of the S3C24X0 register definitions stuff
  - "driver" for the built-in S3C24X0 RTC

* Patches by Yuli Barcohen, 12 Jun 2003:
  - Add MII support and Ethernet PHY initialization for MPC8260ADS board
  - Fix incorrect SIUMCR initialisation caused by wrong Hard Reset
    configuration word supplied by FPGA on some MPC8260ADS boards

* Patch by Pantelis Antoniou, 10 Jun 2003:
  Unify status LED interface

5 files changed, 130 insertions, 22 deletions

diff --git a/include/configs/MPC8260ADS.h b/include/configs/MPC8260ADS.h
index 30b72076ea..dc2c313193 100644
--- a/include/configs/MPC8260ADS.h
+++ b/include/configs/MPC8260ADS.h
@@ -26,10 +26,6 @@
  * MA 02111-1307 USA
  */
 
-/*
- * Config header file for a MPC8260ADS Pilot 16M Ram Simm, 8Mbytes Flash Simm
- */
-
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
@@ -77,23 +73,45 @@
 #undef	CONFIG_ETHER_ON_SCC		/* define if ether on SCC   */
 #define CONFIG_ETHER_ON_FCC		/* define if ether on FCC   */
 #undef	CONFIG_ETHER_NONE		/* define if ether on something else */
-#define CONFIG_ETHER_INDEX	2	/* which channel for ether  */
 
-#if (CONFIG_ETHER_INDEX == 2)
+#ifdef CONFIG_ETHER_ON_FCC
 
+#define CONFIG_ETHER_INDEX	2	/* which SCC/FCC channel for ethernet */
+
+#if (CONFIG_ETHER_INDEX == 2)
 /*
  * - Rx-CLK is CLK13
  * - Tx-CLK is CLK14
  * - Select bus for bd/buffers (see 28-13)
- * - Half duplex
+ * - Full duplex
  */
 # define CFG_CMXFCR_MASK	(CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
 # define CFG_CMXFCR_VALUE	(CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
 # define CFG_CPMFCR_RAMTYPE	0
-# define CFG_FCC_PSMR		0
+# define CFG_FCC_PSMR		(FCC_PSMR_FDE | FCC_PSMR_LPB)
 
 #endif	/* CONFIG_ETHER_INDEX */
 
+#define CONFIG_MII			/* MII PHY management		*/
+#define CONFIG_BITBANGMII		/* bit-bang MII PHY management	*/
+/*
+ * GPIO pins used for bit-banged MII communications
+ */
+#define MDIO_PORT	2		/* Port C */
+#define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
+#define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
+#define MDIO_READ	((iop->pdat &  0x00400000) != 0)
+
+#define MDIO(bit)	if(bit) iop->pdat |=  0x00400000; \
+			else	iop->pdat &= ~0x00400000
+
+#define MDC(bit)	if(bit) iop->pdat |=  0x00200000; \
+			else	iop->pdat &= ~0x00200000
+
+#define MIIDELAY	udelay(1)
+
+#endif /* CONFIG_ETHER_ON_FCC */
+
 /* other options */
 #define CONFIG_HARD_I2C		1	/* To enable I2C support	*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
@@ -172,9 +190,6 @@
 #define CFG_MEMTEST_START	0x00100000	/* memtest works on */
 #define CFG_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM	*/
 
-#define CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-					/* for versions < 2.4.5-pre5	*/
-
 #define CFG_LOAD_ADDR		0x100000	/* default load address */
 
 #define CFG_HZ			1000	/* decrementer freq: 1 ms ticks */
@@ -239,8 +254,8 @@
 
 #ifndef CFG_RAMBOOT
 #  define CFG_ENV_IS_IN_FLASH	1
-#    define CFG_ENV_ADDR	(CFG_MONITOR_BASE + 0x40000)
-#    define CFG_ENV_SECT_SIZE	0x40000
+#  define CFG_ENV_SECT_SIZE	0x40000
+#  define CFG_ENV_ADDR		(CFG_MONITOR_BASE + CFG_ENV_SECT_SIZE)
 #else
 #  define CFG_ENV_IS_IN_NVRAM	1
 #  define CFG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
diff --git a/include/configs/VCMA9.h b/include/configs/VCMA9.h
index a73281c02f..c0103fc335 100644
--- a/include/configs/VCMA9.h
+++ b/include/configs/VCMA9.h
@@ -59,9 +59,13 @@
 #define CONFIG_COMMANDS \
 			(CONFIG_CMD_DFL	 | \
 			CFG_CMD_CACHE	 | \
+			/*CFG_CMD_JFFS2	 |*/ \
+			/*CFG_CMD_NAND	 |*/ \
 			CFG_CMD_EEPROM	 | \
 			CFG_CMD_I2C	 | \
+			/*CFG_CMD_USB	 |*/ \
 			CFG_CMD_REGINFO  | \
+			CFG_CMD_DATE	 | \
 			CFG_CMD_ELF	 | \
 			CFG_CMD_BSP)
 
@@ -111,6 +115,24 @@
  */
 #define CONFIG_SERIAL1          1	/* we use SERIAL 1 on VCMA9 */
 
+/************************************************************
+ * USB support
+ ************************************************************/
+#if 0
+#define CONFIG_USB_OHCI
+#define CONFIG_USB_KEYBOARD
+#define CONFIG_USB_STORAGE
+
+/* Enable needed helper functions */
+#define CFG_DEVICE_DEREGISTER		/* needs device_deregister */
+#endif
+
+/************************************************************
+ * RTC
+ ************************************************************/
+#define	CONFIG_RTC_S3C24X0	1
+
+
 /* allow to overwrite serial and ethaddr */
 #define CONFIG_ENV_OVERWRITE
 
@@ -138,7 +160,7 @@
 #define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
 #define CFG_MEMTEST_START	0x30000000	/* memtest works on	*/
-#define CFG_MEMTEST_END		0x33F00000	/* 63 MB in DRAM	*/
+#define CFG_MEMTEST_END		0x33F80000	/* 63.5 MB in DRAM	*/
 #define CFG_ALT_MEMTEST
 #define	CFG_LOAD_ADDR		0x33000000	/* default load address	*/
 
@@ -152,6 +174,13 @@
 /* valid baudrates */
 #define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
 
+/************************************************************
+ * Ident
+ ************************************************************/
+/*#define VERSION_TAG "released"*/
+#define VERSION_TAG "unstable"
+#define CONFIG_IDENT_STRING "\n(c) 2003 by MPL AG Switzerland, MEV-10080-001 " VERSION_TAG
+
 /*-----------------------------------------------------------------------
  * Stack sizes
  *
@@ -204,6 +233,48 @@
 #define CFG_ENV_SIZE		0x10000	/* Total Size of Environment Sector */
 #endif
 
-#define MULTI_PURPOSE_SOCKET_ADDR 0
+
+#define CFG_JFFS2_FIRST_BANK	0
+#define CFG_JFFS2_NUM_BANKS	1
+
+#define MULTI_PURPOSE_SOCKET_ADDR 0x08000000
+
+/*-----------------------------------------------------------------------
+ * NAND flash settings
+ */
+#if (CONFIG_COMMANDS & CFG_CMD_NAND)
+
+#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
+#define SECTORSIZE 512
+
+#define ADDR_COLUMN 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
+
+#define NAND_ChipID_UNKNOWN 	0x00
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+
+#define NAND_WAIT_READY(nand)	NF_WaitRB()
+
+#define NAND_DISABLE_CE(nand)	NF_SetCE(NFCE_HIGH)
+#define NAND_ENABLE_CE(nand)	NF_SetCE(NFCE_LOW)
+
+
+#define WRITE_NAND_COMMAND(d, adr)	NF_Cmd(d)
+#define WRITE_NAND_COMMANDW(d, adr)	NF_CmdW(d)
+#define WRITE_NAND_ADDRESS(d, adr)	NF_Addr(d)
+#define WRITE_NAND(d, adr)		NF_Write(d)
+#define READ_NAND(adr)			NF_Read()
+/* the following functions are NOP's because S3C24X0 handles this in hardware */
+#define NAND_CTL_CLRALE(nandptr)
+#define NAND_CTL_SETALE(nandptr)
+#define NAND_CTL_CLRCLE(nandptr)
+#define NAND_CTL_SETCLE(nandptr)
+
+#define CONFIG_MTD_NAND_VERIFY_WRITE	1
+#define CONFIG_MTD_NAND_ECC_JFFS2	1
+
+#endif	/* CONFIG_COMMANDS & CFG_CMD_NAND */
 
 #endif	/* __CONFIG_H */
diff --git a/include/configs/smdk2400.h b/include/configs/smdk2400.h
index d0ad65ef2c..a557bc6cf9 100644
--- a/include/configs/smdk2400.h
+++ b/include/configs/smdk2400.h
@@ -86,10 +86,14 @@
 
 #define	CONFIG_TIMESTAMP	1	/* Print timestamp info for images */
 
+/* Use s3c2400's RTC */
+#define CONFIG_RTC_S3C24X0	1
+
 #ifndef USE_920T_MMU
-#define CONFIG_COMMANDS_tmp	(CONFIG_CMD_DFL & ~CFG_CMD_CACHE)
+#define CONFIG_COMMANDS_tmp	((CONFIG_CMD_DFL & ~CFG_CMD_CACHE) | \
+				 CFG_CMD_DATE)
 #else
-#define CONFIG_COMMANDS_tmp	(CONFIG_CMD_DFL)
+#define CONFIG_COMMANDS_tmp	(CONFIG_CMD_DFL | CFG_CMD_DATE)
 #endif
 
 #ifdef CONFIG_HWFLOW
diff --git a/include/configs/smdk2410.h b/include/configs/smdk2410.h
index 65dd3fec25..0dcbbb063d 100644
--- a/include/configs/smdk2410.h
+++ b/include/configs/smdk2410.h
@@ -67,16 +67,29 @@
  */
 #define CONFIG_SERIAL1          1	/* we use SERIAL 1 on SMDK2410 */
 
+/************************************************************
+ * RTC
+ ************************************************************/
+#define	CONFIG_RTC_S3C24X0	1
+
 /* allow to overwrite serial and ethaddr */
 #define CONFIG_ENV_OVERWRITE
 
 #define CONFIG_BAUDRATE		115200
 
-#ifndef USE_920T_MMU
-#define CONFIG_COMMANDS		(CONFIG_CMD_DFL & ~CFG_CMD_CACHE)
-#else
-#define CONFIG_COMMANDS		(CONFIG_CMD_DFL)
-#endif
+/***********************************************************
+ * Command definition
+ ***********************************************************/
+#define CONFIG_COMMANDS \
+			(CONFIG_CMD_DFL	 | \
+			CFG_CMD_CACHE	 | \
+			/*CFG_CMD_NAND	 |*/ \
+			/*CFG_CMD_EEPROM |*/ \
+			/*CFG_CMD_I2C	 |*/ \
+			/*CFG_CMD_USB	 |*/ \
+			CFG_CMD_REGINFO  | \
+			CFG_CMD_DATE	 | \
+			CFG_CMD_ELF)
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
diff --git a/include/configs/trab.h b/include/configs/trab.h
index 2466189a8a..15b6b19251 100644
--- a/include/configs/trab.h
+++ b/include/configs/trab.h
@@ -90,6 +90,9 @@
 
 #define	CONFIG_TIMESTAMP	1	/* Print timestamp info for images */
 
+/* Use s3c2400's RTC */
+#define CONFIG_RTC_S3C24X0	1
+
 #ifdef CONFIG_HWFLOW
 #define CONFIG_COMMANDS_ADD_HWFLOW	CFG_CMD_HWFLOW
 #else
@@ -105,11 +108,13 @@
 #ifndef USE_920T_MMU
 #define CONFIG_COMMANDS		((CONFIG_CMD_DFL & ~CFG_CMD_CACHE) | \
 				 CFG_CMD_BSP			| \
+				 CFG_CMD_DATE			| \
 				 CONFIG_COMMANDS_ADD_HWFLOW	| \
 				 CONFIG_COMMANDS_ADD_VFD	)
 #else
 #define CONFIG_COMMANDS		(CONFIG_CMD_DFL			| \
 				 CFG_CMD_BSP			| \
+				 CFG_CMD_DATE			| \
 				 CONFIG_COMMANDS_ADD_HWFLOW	| \
 				 CONFIG_COMMANDS_ADD_VFD	)
 #endif